Engineering topics

Hunt, L. Roane

Publications and source records attributed to Hunt, L. Roane.

5 records

NASA NTRS1992

Computational method to predict thermodynamic, transport, and flow properties for the modified Langley 8-foot high-temperature tunnel

The Langley 8 foot high temperature tunnel (8 ft HTT) is used to test components of hypersonic vehicles for aerothermal loads definition and structural component verification. The test medium of the 8 ft HTT is obtained by burning a mixture of methane and air under high pressure; the combustion products are expanded through an axisymmetric conical contoured nozzle to simulate atmospheric flight at Mach 7. This facility was modified to raise the oxygen content of the test medium to match that of air and to include Mach 4 and Mach 5 capabilities. These modifications will facilitate the testing of hypersonic air breathing propulsion systems for a wide range of flight conditions. A computational method to predict the thermodynamic, transport, and flow properties of the equilibrium chemically reacting oxygen enriched methane-air combustion products was implemented in a computer code. This code calculates the fuel, air, and oxygen mass flow rates and test section flow properties for Mach 7, 5, and 4 nozzle configurations for given combustor and mixer conditions. Salient features of the 8 ft HTT are described, and some of the predicted tunnel operational characteristics are presented in the carpet plots to assist users in preparing test plans.

Venkateswaran, S.↗

NASA NTRS1991

Aerothermal study in an axial compression corner with shock impingement at Mach 6

An experimental study of an axial-compression interior-corner region with shock impingement was conducted in the NASA Langley 20-inch Mach 6 Tunnel to obtain aerodynamic heating rate distributions. The model, a generic hypersonic engine inlet, had a sharp leading edge forebody, cowl, and interchangeable struts with sharp and blunt leading edges. Experiments were conducted at free-stream unit Reynolds numbers of 1.68 x 10 to the 6th and 3.35 x 10 to the 6th per foot for the blunt and sharp-strut configurations, respectively. For the sharp-strut configuration, with and without trips, the peak heating occurred on the cowl, near the compression corner, downstream of the forebody oblique shock impingement region. The peak heating levels, for both the tripped and untripped boundary-layer flows were about 45 and 50 times the reference laminar heating levels, respectively. The peak heating for the blunt leading edge strut model, which was 30 times the reference value, occurred on the cowl, away from the corner, where the bow shock from the strut leading edge intersected the cowl surface.

Venkateswaran, S.↗

NASA NTRS1990

Aerodynamic pressure and heating-rate distributions in tile gaps around chine regions with pressure gradients at a Mach number of 6.6

Surface and gap pressures and heating-rate distributions were obtained for simulated Thermal Protection System (TPS) tile arrays on the curved surface test apparatus of the Langley 8-Foot High Temperature Tunnel at Mach 6.6. The results indicated that the chine gap pressures varied inversely with gap width because larger gap widths allowed greater venting from the gap to the lower model side pressures. Lower gap pressures caused greater flow ingress from the surface and increased gap heating. Generally, gap heating was greater in the longitudinal gaps than in the circumferential gaps. Gap heating decreased with increasing gap depth. Circumferential gap heating at the mid-depth was generally less than about 10 percent of the external surface value. Gap heating was most severe at local T-gap junctions and tile-to-tile forward-facing steps that caused the greatest heating from flow impingement. The use of flow stoppers at discrete locations reduced heating from flow impingement. The use of flow stoppers at discrete locations reduced heating in most gaps but increased heating in others. Limited use of flow stoppers or gap filler in longitudinal gaps could reduce gap heating in open circumferential gaps in regions of high surface pressure gradients.

Hunt, L. Roane↗

NASA NTRS1988

Aerodynamic pressures and heating rates on surfaces between split elevons at Mach 6.6

An aerothermal study was performed in the Langley 8-Foot High Temperature Tunnel at Mach number 6.6 to define the pressures and heating rates on the surfaces between split elevons similar to those used on the Space Shuttle. Tests were performed with both laminar and turbulent boundary layers on the wing surface upstream of the elevons. The flow in the chordwise gap between the elevons was characterized by flow separation at the gap entrance and flow reattachment at a depth into the gap inversely proportional to the gap width. The gap pressure and heating rate increased significantly with decrease of elevon gap width, and the maximum gap heating rate was proportional to the maximum gap pressure. Correlation of the present results indicate that the gap heating was directly proportional to the elevon windward surface pressure and was not dependent upon whether the boundary layer on the windward elevon surface was laminar or turbulent.

Hunt, L. Roane↗

NASA NTRS1988

Aerothermal tests of quilted dome models on a flat plate at a Mach number of 6.5

Aerothermal tests were conducted in the NASA Langley 8 Foot High Temperature Tunnel (8'HTT) at a Mach number of 6.5 on simulated arrays of thermally bowed metallic thermal protection system (TPS) tiles at an angle of attack of 5 deg. Detailed surface pressures and heating rates were obtained for arrays aligned with the flow and skewed 45 deg diagonally to the flow with nominal bowed heights of 0.1, 0.2, and 0.4 inch submerged in both laminar and turbulent boundary layers. Aerothermal tests were made at a nominal total temperature of 3300 R, a total pressure of 400 psia, a total enthalpy of 950 Btu/lbm, a dynamic pressure of 2.7 psi, and a unit Reynolds number of 400,000 per foot. The experimental results form a data base that can be used to help protect aerothermal load increases from bowed arrays of TPS tiles.

Glass, Christopher E.↗