Engineering topics

Hurley, David H

Publications and source records attributed to Hurley, David H.

12 records

DOE OSTI2023

In-Situ Transmission Electron Microscopy Study of the Evolution of Extended Defects in Oxide Nuclear Fuels

In-situ transmission electron microscopy (TEM) with simulated extreme environments is an effective tool for understanding and tracking microstructural changes down to the atomic scale. The objective of this research is to study the effect of temperature on the evolution of extended defects in ThO2 and UO2. Here, we present in-situ TEM isochronal thermal annealing experiments using a micro-electro-mechanical-system (MEMS)-based heating holder. ThO2 and UO2 single crystal specimens were grown inside an inert silver ampoule using hydrothermal synthesis. Both samples were irradiated using 2 MeV protons at 600oC up to 0.1 dpa at Texas A&M University’s Accelerator Laboratory. Fig. 1a shows a weak-beam dark field TEM image of ThO2 after irradiation, indicating the presence of faulted 1/3 <111> type dislocation loops. This presentation will discuss the effect of annealing temperature (600oC, 800oC, 1000oC, 1100oC, etc.) on dislocation loop density, size and distribution, loop nature (interstitial/vacancies) and Burgers vector, as well as the formation of voids in both ThO2 and UO2. This work will also discuss the interaction between defects during annealing. The in-situ TEM annealing cycle is shown in Fig 1b. This research significantly improves the understanding of defect behavior in oxide nuclear fuels with temperature and will aid computational modeling efforts. This work was supported as part of the Center for Thermal Energy Transport under Irradiation (TETI) Energy Frontier Research Center, funded by the U.S. Department of Energy Office of Science.

36 MATERIALS SCIENCE↗

DOE OSTI2022

A combined theoretical-experimental investigation of thermal transport in low-dose irradiated thorium dioxide

During reactor operation, nuclear fuels are subject to extreme temperature and irradiation conditions which can significantly degrade the fuel's thermal transport properties. The reduction in thermal conductivity of the fuel as a result of irradiation-induced lattice defects is arguably the most important fuel performance metric in regard to reactor efficiency and safety. Because thorium dioxide (ThO2) is suitable as a model system for more complex materials such as UO2 and its mixed oxides, we present a theoretical investigation of thermal conductivity reduction seen in defect-bearing thorium dioxide and compare directly to experimental measurements. Phonon-mediated thermal transport of the fuel is modeled by a solution to the Boltzmann transport equation (BTE) for phonons. A cluster dynamics (CD) model for lattice defect evolution during irradiation predicts defect densities which are used as input to the BTE for modeling phonon-defect scatterings. Phonon scatterings by lattice defects include those from point defects and vacancy clusters and interstitial clusters of various sizes. The CD model is benchmarked against structural defect characterization of irradiated thorium dioxide using electron microscopy. Thermal conductivity predicted by the BTE model is compared to measured values for irradiated thorium dioxide specimens below room temperature to isolate effects of phonon-defect scattering from intrinsic 3-phonon processes, which dominate at higher temperatures. The computed conductivity values are in partial agreement at temperatures close to room temperature while slight deviations are observed at the lowest measured temperatures, suggesting that implemented phonon-defect scattering cross-section expressions may not be adequate for low temperatures. The presented work provides a necessary investigation of the influence of irradiation induced defects on fuel performance and represents a first step toward a full characterization of phonon mediated thermal transport in irradiated materials with complex defect microstructure.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Development of a Laser Ultrasonics-based Approach for Rapid Screening of High Entropy Alloys

This project utilized a laser ultrasonic technique to systematically study temperature-induced evolution of material properties in a set of interrelated binary alloys and a high entropy alloy (HEA) fabricated using arc-melting and spark plasma sintering processes. This technique involved the use of a nanosecond duration, high-intensity pulsed laser to thermo-elastically generate ultrasonic waves that propagate in the bulk of the metal alloy. Sub-nanometer-scale displacements associated with the propagating bulk ultrasonic waves were detected along the epicenter on the opposite surface of the sample using a 1 GHz bandwidth photorefractive interferometer. Phase transformations and microstructural changes were inferred from the temperature-dependent trends in the bulk acoustic velocities and features in the ultrasonic epicentral waveforms measured in the binary alloys. These inferences were then correlated with electron/optical microscopy observations and predictions using calculations of phase diagrams (CALPHAD). The results showed that the laser-generated ultrasonic pulses were strongly influenced by changes in material microstructure and could accurately track thermally driven phase transformations and detect the presence of microscale heterogeneities (grain boundaries, dendritic structures, etc.) in the set of binary alloy samples. The measurement approach was then applied to a quinary HEA sample for estimating phase transition temperature and determining microstructural heterogeneity. The rapid, non-contact and non-destructive ultrasonic testing approach demonstrated here is amenable to high throughput combinatorial investigations that can be applied to graded composition HEAs produced using advanced manufacturing methods. When paired with atomistic simulations and CALPHAD modeling, this approach can overcome the bottlenecks faced by current material characterization methods in efficiently screening the vast discovery space of HEAs that spans over a hundred million unique quinary alloy compositions.

36 MATERIALS SCIENCE↗

DOE OSTI2022

A laser ultrasonics-based approach for rapid screening of high entropy alloys

This project demonstrates a laser ultrasonics-based characterization methodology for rapid metallic materials design and discovery via in situ determination of phases, microstructures and elastic properties with respect to temperature. Ultrasonic waves are strongly affected by material microstructure, and therefore serve as a facile means to probe elastic properties, phase content and their size distributions and volume fractions. In this study, a laser ultrasonic technique is used to systematically study the evolution of properties in a set of interrelated simple binary alloys and high entropy alloys (HEA). Phase transformations and microstructural changes inferred from the ultrasonic signals will be correlated with electron microscopy data and predictions using calculations of phase diagrams (CALPHAD). The non-contact and non-destructive ultrasonic testing approach developed in this study could overcome several limitations associated with current material characterization methods for materials discovery. It is expected that laser ultrasonics-based methodology developed in this work will be utilized to evaluate novel graded composition HEAs currently being developed at the Idaho National Laboratory (INL) using advanced manufacturing methods based on direct energy deposition and spark plasma sintering processes, and contribute to accelerate the discovery of HEAs.

36 MATERIALS SCIENCE↗

DOE OSTI2022

A laser ultrasonics-based approach for rapid screening of high entropy alloys

The primary objective of this seed project is to develop a laser ultrasonics-based characterization methodology for rapid metallic materials design and discovery via in situ determination of phases, microstructures and elastic properties with respect to temperature. Ultrasonic waves are strongly affected by material microstructure, and therefore, serve as a facile means to probe elastic properties, phase content and their size distributions and volume fractions. In this study, a laser ultrasonic technique will be used to systematically study the evolution of properties in a set of interrelated simple binary alloys and high entropy alloys (HEA). Phase transformations and microstructural changes inferred from the ultrasonic signals will be correlated with electron microscopy data and predictions using calculations of phase diagrams (CALPHAD). The non-contact and non-destructive ultrasonic testing approach developed in this study could overcome several limitations associated with current material characterization methods for materials discovery. It is expected that the products of the proposed work will be utilized to evaluate novel graded composition HEAs currently being developed at the Idaho National Laboratory (INL) using advanced manufacturing methods based on direct energy deposition and spark plasma sintering processes, and contribute to accelerate the discovery of HEAs.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Impact of Irradiation-induced Lattice Defects and Dopants on Thermal Transport in Oxide Nuclear Fuels

Advanced nuclear reactor concepts aim to use fuels that must withstand unprecedented temperature and radiation extremes. In these fuels, thermal energy transport under irradiation is directly related to fuel longevity, reactor safety, and is arguably one of the most important performance metrics. Here we provide a comprehensive, first-principles-informed treatment of phonon mediated thermal transport in a defect-bearing actinide oxide with direct comparison to experimental measurements. Pristine and proton irradiated thorium dioxide was chosen as a model system to treat the complexity of thermal transport in the presence of lattice defects. A thermal transport model is implemented using the linearized Boltzmann transport equation (LBTE) with input from first principles calculations and defect evolution models. The output of the LBTE is compared directly to mesoscopic measurements of thermal conductivity on length scales commensurate with defect accumulation. Parametric measurements of conductivity with irradiation dose and temperature reveal a monotonic decrease in conductivity with irradiation dose, in the range of 0.001 dpa to 0.1 dpa. Besides radiation-induced defects, doping the thorium dioxide crystal with small quantities of uranium atoms also results in a drastic reduction in thermal conductivity. Temperature-dependent measurements of thermal conductivity in uranium-doped thorium dioxide single crystals suggests a resonant scattering mechanism is responsible for the observed reduction. This comprehensive, atomistic- to meso-scale treatment provides the necessary basis to investigate thermal transport under irradiation in more complex systems that exhibit strong electron correlation. This is a poster presentation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Probing Microstructure-induced Swelling & Thermal Property Changes in Ion-Irradiated Oxide Fuels using Laser-generated Surface Acoustic Waves

Radiation of fuel rods with neutrons during a fission reaction in a nuclear reactor is known to affect the material microstructure of the fuel as a result of fission fragment damage, and lead to the formation of atomic-level defects such as voids, dislocation loops, and lattice swelling from fission-gas release. A consequence of the radiation-induced damage in nuclear fuels is the drastic alteration of material properties, in particular, the reduction of the thermal conductivity – a key parameter that governs the transport of thermal energy released from fissile fuel atoms to the surrounding coolant. Swelling can induce high stresses and ultimate failure of the cladding. A fundamental understanding of the role of radiation-induced damage on the thermal transport and mechanical properties of nuclear fuels is therefore critical for efficient, reliable and safe operation of a nuclear power plant. As opposed to conventional post-irradiation examination techniques that are often time-consuming and require significant sample preparation, laser-based characterization methods have emerged as promising non-contact, non-destructive tools to measure the evolution of microstructure-induced material property changes. Moreover, laser methods offer the promise of in-situ characterization while the material is being irradiated. This project aims to develop an improved understanding of the impact of radiation-induced changes to material microstructure on the thermal and elastic properties of nuclear materials. A laser ultrasonic technique, known as the transient grating (TG) spectroscopy method, is used to simultaneously measure thermal diffusivity and elastic properties in unirradiated and ion-irradiated oxide nuclear fuel samples. The results will complement on-going investigations on electron- and phonon-mediated thermal transport in nuclear materials and will provide foundational work for incorporating the influence of defects in fuel performance codes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

FY20 Status Report on Photothermal Radiometry Development

This report documents FY20 progress in the development of a benchtop photothermal radiometry (PTR) instrument for the measurement of thermal diffusivity. A PTR system incorporating Off-Axis Parabolic (OAP) mirrors was designed and tested. Additionally, a novel analysis technique that accounts for systematic errors that affect measurement accuracy was implemented. Measurements on samples with a range of thermal diffusivities using the PTR setup along with the new analysis technique resulted in improved accuracy and repeatability. Areas for future development work are set forth.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Investigation of Exciton Delocalization and Exciton Coherence in Chromophores and Acoustic Nanostructures

Quantum materials have a rich potential for providing transformative energy technologies ranging from new energy efficient computation paradigms to lossless energy transport across the national grid. The field of quantum materials, however, is still in its infancy with many quantum materials systems requiring cyrogenic temperatures to be viable. Few viable, room-temperature quantum materials systems have been identified; therefore, identifying additional such systems is vitally important. This state of the science combined with the low number of potential systems that exhibit room-temperature quantum character make this field of research fertile ground for EPSCoR states (states eligible for funding under the Established Program to Stimulate Competitive Research program) such as Idaho to compete on a national level. As a result, this project proposed and accomplished two main goals in advancing two room-temperature quantum materials systems: (1) advance the science for demonstrating room temperature exciton delocalization in two excitonic systems and (2) build capacity and expertise in developing and understanding quantum materials at both Boise State University and Idaho National Laboratory. The work at Boise State focused mainly on the use of nucleic acid self-assembled chromophore molecule networks that offer a much easier and mature approach to construct aggregates of chromophores that can be tailored to specific two-dimensional and three-dimensional geometries and allow exciton manipulation towards achieving room-temperature quantum computation. A second complementary effort performed at Boise State and INL focused on confining excitons on quantum length scales using coherent surface acoustic phonons

36 MATERIALS SCIENCE↗

DOE OSTI2020

MESOSCALE THERMAL TRANSPORT MEASUREMENTS OF MULTI-PHASE AND POROUS NUCLEAR FUELS USING A SQUARE-WAVE PULSE THERMOREFLECTANCE TECHNIQUE

The safe and efficient operation of nuclear reactors require accurate knowledge of peak temperatures in the fuel assemblies. The temperature profiles are governed by the thermal transport properties of the fuel, namely the thermal conductivities (k) and thermal diffusivities (D). These values can be very difficult to measure as they are known to vary considerably from the measured bulk values of the fresh fuel, and quickly degrade with increasing burnup [1 -3] . Laser-based techniques have been effectively used for non-destructive and non-contact thermal transport measurements of a wide variety of materials, including nuclear materials [4-6] that would otherwise prove too hazardous or difficult to measure otherwise. In this study, a new thermoreflectance technique known as square-pulse transient thermoreflectance (SPTR) is described and used to determine the mesoscale thermal diffusivity of both uranium sesquisilicide (U3Si2) and uranium nitride (UN) phases in a composite fuel with micron level spatial resolution [7]. This technique employs a rapid train of square-wave pulses from an excitation laser to create a periodic heat flux on a gold coated sample surface. Surface adsorption results in transient film temperatures and hence rapid fluctuations in thermoreflectance that can be measured via a detection laser coupled with a digital oscilloscope. The lasers are coaxially focused on the sample surface, allowing for a sample measurement area of a single convolved laser spot size (~2 µm). A sensitivity analysis was conducted to identify key measurement parameters of this technique using reference materials with a range of thermal conductivities comparable to those of both ceramic, composite, and metal nuclear fuel types (1.4 – 27.2 W/m-K). The reference materials were measured using the new technique as well as a spatial-domain thermoreflectance technique (SDTR) previously reported for a comparison [8]. Additionally, measurements of several U3Si2 and UN phase regions of a polished UN/U3Si2 (70/30 vol.%) sample were taken, and the resulting calculated D values are reported, with both techniques showing excellent agreement between samples. This technique was used to scan a multiphase region at 5 micron increments to generate a local diffusivity map, demonstrating the utility of the techniques for measuring thermal transport properties in specimens with precipitates and secondary phases. Furthermore, the technique is currently being applied to measure thermal properties of Fast Flux Test Reactor (FFTR) irradiated metal fuel specimens whose porous microstructure make it very difficult to measure using other techniques. Comparison of the local scale measurements are compared with the pre-irradiated fuel samples to show the degradation of thermal transport in fuels due to pores from fission gas bubbles and other irradiation induced defects.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Influence of Irradiation-induced Microstructural Defects on Thermal Transport in Single Crystal Thorium Dioxide

Microstructural defects formed as a result of fission fragment damage are known to drastically alter thermal conductivity, a fuel property that governs the efficiency of a nuclear reactor. A fundamental understanding of radiation-induced effects on thermal transport is critical for the development of advanced fuels. Ion-irradiation has widely been used to simulate the effects of neutron-irradiation by seeding atomic-to-nanoscale defects of controllable size and density. In this work, we investigate the influence of microstructural defects, induced by ion-irradiation, on the thermal properties of single crystal thorium dioxide samples grown using the hydrothermal technique. The samples were irradiated using 2 MeV protons at room temperature. A laser-based modulated thermoreflectance technique was used to measure the thermal diffusivity and conductivity within the damaged ThO2 region. The experimentally measured thermal properties were compared with Boltzmann Transport Equation predictions, to determine the impact of various defect types on the thermal properties of ThO2.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Scoping Studies to ascertain the change in the phase transition temperature of metallic fuels

Microstructure evolution due to irradiation in a nuclear reactor can have a dramatic effect on material properties. A better understanding of this evolution is necessary for developing improved nuclear fuels and materials. In the current scoping study we evaluate the influence of irradiation induced defects on the recrystallization temperature of a single component fuel surrogate.

36 MATERIALS SCIENCE↗