Search NASA⌕ Search

Engineering topics

Hurricane, O.

Publications and source records attributed to Hurricane, O..

6 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Hohlraum Reheating from Burning NIF Implosions

As fusion experiments at the National Ignition Facility (NIF) approach and exceed breakeven, energy from the burning capsule is predicted to couple to the gold walls and reheat the hohlraum. For example, on December 5, 2022, experiment N221204 exceeded target breakeven, historically achieving 3.15 MJ of fusion energy from 2.05 MJ of laser drive; for the first time, energy from the igniting capsule reheated the hohlraum beyond the peak laser-driven radiation temperature of 313 eV to a peak of 350 eV, in less than half a nanosecond. This reheating effect has now been unambiguously observed by the two independent Dante calorimeter systems across multiple experiments, and is shown to result from reheating of the remnant tungsten-doped ablator by the exploding core, which is heated by alpha deposition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Diagnosing the origin and impact of low-mode asymmetries in ignition experiments at the National Ignition Facility

Inertial confinement fusion ignition requires high inflight shell velocity, good energy coupling between the hotspot and shell, and high areal density at peak compression. Three-dimensional asymmetries caused by imperfections in the drive symmetry or target can grow and damage the coupling and confinement. Recent high-yield experiments have shown that low-mode asymmetries are a key degradation mechanism and contribute to variability. Here we show the experimental signatures and impacts of asymmetry change with increasing implosion yield given the same initial cause. This letter has implications for improving robustness to a key degradation in ignition experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Model validation for inferred hot-spot conditions in National Ignition Facility experiments

Progress toward ignition requires accurately diagnosing current conditions and assessing proximity metrics for implosion experiments on the National Ignition Facility. Hot-spot conditions are not directly measured, but rather inferred, often using simple 0- and 1D models [P. Patel et al., Phys. Plasmas 27, 050901 (2020)]. In this work, we present a detailed accuracy validation exercise using a set of ~20,000 2D simulations encompassing a variety of performance and degradation levels. We find good agreement between the model-inferred pressure and the simulated burn-weighted pressure at peak neutron production and also present results on the precision of inferred quantities using a Markov-Chain Monte Carlo algorithm.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Fill tube dynamics in inertial confinement fusion implosions with high density carbon ablators

Plasma jets, such as γ-ray burst jets, Herbig–Haro jets, μ-quasar jets, and active galactic nuclei jets, are found throughout the universe [S. Mendoza et al., Rev. Mex. Astron. Astrofis. 41, 453 (2005)]. Plasma jets are also present in indirect drive inertial confinement fusion experiments originating from the capsule's fill tube and occasionally from divots and voids in the capsules, particles on the exterior of the capsule, or from the tent holding the capsule in the target. This paper looks at two different gas-filled capsule implosions containing a plasma jet resulting from a capsule fill tube and fill channel, both of which utilized high density carbon ablators. Two models were developed, a drag and a snowplow model, which use the time-dependent motion of the injected mass through the hotspot to estimate the mass injected into the hotspot from the fill tube and channel, arriving at an average injected mass of ~84.5 ± 25.5 ng for the first experiment and 91 ± 20 ng for the second experiment. Furthermore, unlike previous methods to estimate fill tube injected mass, these techniques do not assume that the mixed mass is in thermal equilibrium with the hotspot or that the x-ray emission is only coming from within the hotspot itself. This paper also discusses the features seen in these experiments which include limb brightening in the shell for undoped ablators and flattening in the ablator from shadowing by the fill tube.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Measurements of enhanced performance in an indirect drive inertial confinement fusion experiment when reducing the contact area of the capsule support

Experimental results from indirectly driven inertial confinement fusion experiments testing the performance gained from using an alternate capsule tent support are reported. The polar tent describes an alternate geometry for the thin membrane used to support the Deuterium–Tritium (DT) filled capsule. In this work, the contact area is reduced by 23 times by locating the tent support close to the poles of the capsule. The polar tent experiments are repeats of previous 3 shock 1.63 MJ, 400 TW high foot experiments and use a 165 μm thick silicon doped carbon hydrogen plastic (CH) shell. Using the polar tent support, we report a DT neutron yield of 1.07 ×1016, 76% higher than the expected Y DT ∝V 7.7 scaling. This is, at the time of writing, the highest neutron yield to date from a CH shell implosion. Furthermore, we find that the inferred pressure when using the polar tent is significantly above the model based on analytic scaling even when accounting for tent effects. Analysis of x-ray and neutron images shows the reduction of lobes produced by nominal tent features. The reduction of these features in the polar tent experiments leads to decreased low mode (P2 and P4) asymmetry compared to the nominal tent results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗