Engineering topics

Hurst, N. C.

Publications and source records attributed to Hurst, N. C..

6 records

DOE OSTI2024

Tokamak Plasmas with Density up to 10 Times the Greenwald Limit

Current-carrying, toroidal laboratory plasmas typically cannot be sustained with an electron density above the empirical Greenwald limit. Presented here are tokamak experiments in the Madison Symmetric Torus with a density up to an unprecedented level about ten times this limit. This is thought to be made possible in part by a thick, stabilizing, conductive wall, and a high-voltage, feedback-controlled power supply driving the plasma current. The radial profile of the toroidal current flattens around twice the limit, without the edge collapse routinely observed in other experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

MST resistive wall tearing mode simulations

Here, the Madison Symmetric Torus (MST) is a toroidal device that, when operated as a stan dard tokamak, does not have major disruptions. Unlike most tokamaks, the MST plasma is surrounded by a close fitting highly conducting wall, with a resistive wall penetration time two orders of magnitude longer than in JET or DIII-D, and three times longer than in ITER. The MST can operate with edge q a &LessSlantEqual; 2, unlike standard tokamaks. Simulations presented here indicate that the MST is unstable to resistive wall tearing modes (RWTMs) and resistive wall modes (RWMs). They could in principle cause disruptions, but the predicted thermal quench time is much longer than the experimental pulse time. If the MST thermal quench time were comparable to measurements in JET and DIII-D, theory and simulations predict that disruptions would have been observed in MST. This is consistent with the modeling herein, predicting that disruptions are caused by RWTMs and RWMs. In the low q a ~ 2 regime of MST, the RWTM asymptotically satisfies the RWM dispersion relation. The transition from RWTM to RWM occurs smoothly at q a = m/n, where m, n are poloidal and toroidal mode numbers.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Self-organized magnetic equilibria in tokamak plasmas with very low edge safety factor

Tokamak plasmas often exhibit self-organizing behavior in which internal modes shape the toroidal current density profile, a common example being the sawtooth instability. However, such behavior has not been studied in detail for edge safety factor below 2 due to disruptive kink instabilities that typically prevent operation in this regime. Now, steady tokamak plasmas with an edge safety factor down to 0.8 have been created in the Madison Symmetric Torus, where disruptions are prevented due to a thick, conductive wall and a feedback power supply that sustains the plasma current. Internal measurements and nonlinear magnetohydrodynamic modeling reveal a family of safety factor profiles with a central value clamped near unity as the edge safety factor decreases, indicating current profile broadening through a relaxation process. Furthermore, as the safety factor decreases, the magnetic fluctuations become irregular, and the electron energy confinement time decreases.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Inviscid damping of an elliptical vortex subject to an external strain flow

Inviscid spatial Landau damping is studied experimentally for the case of oscillatory motion of a two-dimensional vortex about its elliptical equilibrium in the presence of an applied strain flow. Here, the experiments are performed using electron plasmas in a Penning–Malmberg trap. They exploit the isomorphism between the two-dimensional Euler equations for an ideal fluid and the drift-Poisson equations for the plasma, where plasma density is the analog of vorticity. Perturbed elliptical vortex states are created using E x B strain flows, which are generated by applying voltages to electrodes surrounding the plasma. Measurements of spatial Landau damping (also called critical-layer damping) are in agreement with previous studies in the absence of an applied strain, where the damping is due to a resonance between the local fluid motion and the vortex oscillations. Interestingly, the damping rate does not change significantly over a wide range of applied strain rates. This can be accurately predicted from the initial vorticity profile, even though the resonant frequency is reduced substantially due to the applied strain. For higher amplitude perturbations, nonlinear trapping oscillations also exhibit behavior similar to the strain-free case. In principle, higher-order effects of the applied strain, such as separatrix crossing of peripheral vorticity and interactions with harmonics of the fundamental resonance, are expected to change the damping rate. However, this occurs only for conditions that are not realized in the experiments described here. Vortex-in-cell simulations are used to investigate the possible roles of these effects.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Adiabatic behavior of an elliptical vortex in a time-dependent external strain flow

The adiabatic behavior of two-dimensional (2D) fluid vortices subject to slowly varying, time-dependent external strain flows is studied theoretically, and experimentally using magnetized non-neutral electron plasmas. Here the E × B drift dynamics of the electrons perpendicular to the magnetic field are analogous to the motion of fluid vorticity under the 2D Euler equations describing ideal fluids. A low-dimensional elliptical vortex patch model is used along with a WKB approximation to derive a formula for the breaking of an adiabatic invariant due to the changing external flow. The invariant is interpreted as the amplitude of a perturbative oscillation about a stable fixed point corresponding to a steady elliptical vortex. Smooth, hyperbolic tangent and piecewise linear ramp functions are considered for the external strain time dependence. Standard exponential breaking is observed in the former case, whereas the latter exhibits a power-law breaking curve with periodic modulation. It is found that a driving term in the equations of motion contributes the majority of the breaking whereas the frequency variation plays a weaker, but significant role. The experimental data agree closely with the theoretical model. The most significant deviation is due to inviscid damping behavior associated with the smooth edges of the experimental vortices, which tends to reduce the amplitude of the oscillation. Finally, the results are compared and contrasted with other related experimental, numerical, and theoretical work.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Instability of an electron-plasma shear layer in an externally imposed strain flow

The E x B shear instability of a two-dimensional (2D) filament (i.e., a thin, rectangular strip perpendicular to the magnetic field) of magnetized pure electron plasma is investigated experimentally in the presence of an externally imposed strain flow. Data are acquired using a specialized Penning–Malmberg trap in which strain flows can be applied in 2D by biasing segmented electrodes surrounding the plasma. The E x B drift dynamics are well-described by the Drift-Poisson equations, which are isomorphic to the 2D Euler equations describing ideal fluids. Thus, the experimental results correspond to the Rayleigh instability of a shear layer in a 2D ideal fluid, where the electron density is analogous to the fluid vorticity. Shear layers are prepared by stretching initially axisymmetric electron vortices using a strong, applied strain flow. The data at early times are in quantitative agreement with a linear model which extends Rayleigh’s work to account for the influence of an external strain flow. In the presence of weak strain, the system approximately maintains a phase relationship that corresponds to an instantaneous Rayleigh eigenmode. The instability develops into the nonlinear regime later in time and at smaller spatial scales as the strain rate is increased. A secondary vortex pairing instability is observed, but it is suppressed when the strain-to-vorticity ratio exceeds roughly 0.025. In this way, vorticity transport perpendicular to the filament is diminished due to the applied strain.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗