Search NASA⌕ Search

Engineering topics

Hwang, D. P.

Publications and source records attributed to Hwang, D. P..

18 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Flow analysis for the nacelle of an advanced ducted propeller at high angle-of-attack and at cruise with boundary layer control

An axisymmetric panel code and a three dimensional Navier-Stokes code (used as an inviscid Euler code) were verified for low speed, high angle of attack flow conditions. A three dimensional Navier-Stokes code (used as an inviscid code), and an axisymmetric Navier-Stokes code (used as both viscous and inviscid code) were also assessed for high Mach number cruise conditions. The boundary layer calculations were made by using the results from the panel code or Euler calculation. The panel method can predict the internal surface pressure distributions very well if no shock exists. However, only Euler and Navier-Stokes calculations can provide a good prediction of the surface static pressure distribution including the pressure rise across the shock. Because of the high CPU time required for a three dimensional Navier-Stokes calculation, only the axisymmetric Navier-Stokes calculation was considered at cruise conditions. The use of suction and tangential blowing boundary layer control to eliminate the flow separation on the internal surface was demonstrated for low free stream Mach number and high angle of attack cases. The calculation also shows that transition from laminar flow to turbulent flow on the external cowl surface can be delayed by using suction boundary layer control at cruise flow conditions. The results were compared with experimental data where possible.

Hwang, D. P.↗
NASA NTRS1993

Effect of a rotating propeller on the separation angle of attack and distortion in ducted propeller inlets

The present study represents an extension of an earlier wind tunnel experiment performed with the P&W 17-in. Advanced Ducted Propeller (ADP) Simulator operating at Mach 0.2. In order to study the effects of a rotating propeller on the inlet flow, data were obtained in the UTRC 10- by 15-Foot Large Subsonic Wind Tunnel with the same hardware and instrumentation, but with the propeller removed. These new tests were performed over a range of flow rates which duplicated flow rates in the powered simulator program. The flow through the inlet was provided by a remotely located vacuum source. A comparison of the results of this flow-through study with the previous data from the powered simulator indicated that in the conventional inlet the propeller produced an increase in the separation angle of attack between 4.0 deg at a specific flow of 22.4 lb/sec-sq ft to 2.7 deg at a higher specific flow of 33.8 lb/sec-sq ft. A similar effect on separation angle of attack was obtained by using stationary blockage rather than a propeller.

Boldman, D. R.↗
NASA NTRS1993

Effect of a rotating propeller on the separation angle of attack

The present study represents an extension of an earlier wind tunnel experiment performed with the P&W 17-in. Advanced Ducted Propeller (ADP) Simulator operating at Mach 0.2. In order to study the effects of a rotating propeller on the inlet flow, data were obtained in the UTRC 10- by 15-Foot Large Subsonic Wind Tunnel with the same hardware and instrumentation, but with the propellar removed. These new tests were performed over a range of flow rates which duplicated flow rates in the powered simulator program. The flow through the inlet was provided by a remotely located vacuum source. A comparison of the results of this flow-through study with the previous data from the powered simulator indicated that in the conventional inlet the propeller produced an increase in the separation angle of attack between 4.0 deg at a specific flow of 22.4 lb/sec-sq ft to 2.7 deg at a higher specific flow of 33.8 lb/sec-sq ft. A similar effect on separation angle of attack was obtained by using stationary blockage rather than a propeller.

Boldman, D. R.↗
NASA NTRS1991

Evaluation of panel code predictions with experimental results of inlet performance for a 17-inch ducted prop/fan simulator operating at Mach 0.2

An axisymmetric panel code was used to evaluate a series of ducted propeller inlets. The inlets were tested in the Lewis 9 by 15 Foot Low Speed Wind Tunnel. Three basic inlets having ratios of shroud length to propeller diameter of 0.2, 0.4, and 0.5 were tested with the Pratt and Whitney ducted prop/fan simulator. A fourth hybrid inlet consisting of the shroud from the shortest basic inlet coupled with the spinner from the largest basic inlet was also tested. This later configuration represented the shortest overall inlet. The simulator duct diameter at the propeller face was 17.25 inches. The short and long spinners provided hub-to-tip retios of 0.44 at the propeller face. The four inlets were tested at a nominal free stream Mach number of 0.2 and at angles of attack from 0 degrees to 35 degrees. The panel code method incorporated a simple two-part separation model which yielded conservative estimates of inlet separation.

Boldman, D. R.↗
NASA NTRS1991

Evaluation of panel code predictions with experimental results of inlet performance for a 17-inch ducted prop/fab simulator operating at Mach 0.2

An axisymmetric panel code was used to evaluate a series of ducted propeller inlets. The inlets were tested in the Lewis 9 by 15 Foot Low Speed Wind Tunnel. Three basic inlets having ratios of shroud length to propeller diameter of 0.2, 0.4, and 0.5 were tested with the Pratt and Whitney ducted prop/fan simulator. A fourth hybrid inlet consisting of the shroud from the shortest basic inlet coupled with the spinner from the largest basic inlet was also tested. This later configuration represented the shortest overall inlet. The simulator duct diameter at the propeller face was 17.25 inches. The short and long spinners provided hub-to-tip ratios of 0.44 at the propeller face. The four inlets were tested at a nominal free stream Mach number of 0.2 and at angles of attack from 0 degrees to 35 degrees. The panel code method incorporated a simple two-part separation model which yielded conservative estimates of inlet separation.

Boldman, D. R.↗
NASA NTRS1986

A numerical analysis applied to high angle of attack three-dimensional inlets

The three-dimensional analytical methods used to analyze subsonic high angle of attack inlets are described. The methods are shown to be in good agreement with experimental results for various three-dimensional high angle of attack inlets. The methods are used to predict aerodynamic characteristics of scarf and slotted-lip inlets.

Hwang, D. P.↗
NASA NTRS1986

A numerical analysis applied to high angle of attack three-dimensional inlets

The three-dimensional analytical methods used to analyze subsonic high angle of attack inlets are described. The methods are shown to be in good agreement with experimental results for various three-dimensional high angle of attack inlets. The methods are used to predict aerodynamic characteristics of scarf and slotted-lip inlets.

Hwang, D. P.↗
NASA NTRS1984

Analytical study of suction boundary layer control for subsonic V/STOL inlets

Analytical procedures used to evaluate the application of suction boundary-layer control (BLC) to subsonic V/STOL inlets are presented. These procedures have been used to analytically predict the optimum (minimum suction power required) location and extent for a suction slot of two different surface resistances within a subsonic V/STOL inlet. Results of this analytical study are presented.

Boles, M. A.↗
NASA NTRS1984

Analytical Study of Blowing Boundary-Layer Control for Subsonic V/STOL Inlets

The analytical methods used to study blowing boundary-layer control (BLC) for subsonic V/STOL inlets are described. The methods are then shown to give good agreement with experimental results, both with and without blowing BLC. Finally, because of this good agreement, the methods were used to determine analytically the optimum (minimum blowing power required) location and height for a blowing slot within a subsonic V/STOL inlet.

Hwang, D. P.↗
NASA NTRS1984

Boundary layer transition effects on flow separation around V/STOL engine inlets at high incidence

Numerical methods for calculating laminar and turbulent boundary layer development around vertical-short take off and landing engine inlets at high incidence angles are investigated. Various transition models were compared and evaluated in calculations off flow separation bound inside the inlet. Results of the transition effects on the boundary layer characteristics at onset of separation for two types of engine inlet geometries are presented. Some of the numerical results are compared with existing wind-tunnel test data for scaled inlet models to demonstrate the effects of transition models in the numerical scheme. The effects of transition modeling on the boundary layer development are illustrated for typical engine operating conditions.

Chou, D. C.↗
NASA NTRS1983

Analytical study of blowing boundary layer control for subsonic V/STOL inlets

The analytical methods used to study blowing boundary-layer control (BLC) for subsonic V/STOL inlets at the NASA Lewis Research Center are briefly described. The methods are then shown to give good agreement with experimental results, both with and without blowing BLC. Finally, because of this good agreement, the methods have been used to determine analytically the optimum (minimum blowing power required) location and height for a blowing slot within a subsonic V/STOL inlet. Results of this analytical study are presented.

Hwang, D. P.↗
NASA NTRS1982

Experimental and analytical results of tangential blowing applied to a subsonic V/STOL inlet

Engine inlets for subsonic V/STOL aircraft must operate over a wide range of conditions without internal flow separation. Experimental and analytical investigations were conducted to evaluate the effectiveness of tangential blowing to maintain attached flow to high angles of attack. The inlet had a relatively thin lip with a blowing slot located either on the lip or in the diffuser. The height and width of these slots was varied. Experimentally determined flow separation boundaries showed that lip blowing achieved higher angle of attack capability than diffuser blowing. This capability was achieved with the largest slot circumferential extent and either of the two slot heights. Predicted (analytical) separation boundaries showed good agreement except at the highest angles of attack.

Burley, R. R.↗
NASA NTRS1982

A summary of V/STOL inlet analysis methods

The methods used to analyze the aerodynamic performance of V/STOL inlets at the NASA Lewis Research Center are briefly described. Recent extensions and applications of the method are emphasized. They include the specification of the Kutta condition for a slotted inlet, the calculation of suction and tangential blowing for boundary layer control, and the analysis of auxiliary inlet geometries. A comparison is made with experiment for the slotted inlet and also for tangential blowing. Finally, an optimum inlet diffuser velocity distribution is developed.

Hwang, D. P.↗
NASA NTRS1981

A summary of V/STOL inlet analysis methods

Methods to analyze the aerodynamic performance of V/STOL inlets at the NASA Lewis Research Center are discussed with emphasis on recent extensions and applications. Methods include the specification of the Kutta condition for a slotted inlet, the calculation of suction and tangential blowing for boundary layer control, and the analysis of auxiliary inlet geometries at angles of attack. An optimum diffuser velocity distribution is also developed, which can result in the shortest no-boundary layer control inlet and the lowest loss for the required amount of diffusion.

Hwang, D. P.↗
NASA NTRS1981

A summary of V/STOL inlet analysis methods

Recent extensions and applications of the methods are emphasized. They include the specification of the Kutta condition for a slotted inlet, the calculation of suction and tangential blowing for boundary layer control, and the analysis of auxiliary inlet geometries at angles of attack. A comparison is made with experiment for the slotted inlet. An optimum diffuser velocity distribution was developed.

Hwang, D. P.↗