Search NASA⌕ Search

Engineering topics

Hwang, Inhui

Publications and source records attributed to Hwang, Inhui.

27 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Unconventional Hysteretic Transition in a Charge Density Wave

Hysteresis underlies a large number of phase transitions in solids, giving rise to exotic metastable states that are otherwise inaccessible. Here, we report an unconventional hysteretic transition in a quasi-2D material, EuTe 4 . By combining transport, photoemission, diffraction, and x-ray absorption measurements, we observe that the hysteresis loop has a temperature width of more than 400 K, setting a record among crystalline solids. The transition has an origin distinct from known mechanisms, lying entirely within the incommensurate charge density wave (CDW) phase of EuTe 4 with no change in the CDW modulation periodicity. We interpret the hysteresis as an unusual switching of the relative CDW phases in different layers, a phenomenon unique to quasi-2D compounds that is not present in either purely 2D or strongly coupled 3D systems. Furthermore, our findings challenge the established theories on metastable states in density wave systems, pushing the boundary of understanding hysteretic transitions in a broken-symmetry state.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

Enabling High-Performance NASICON-Based Solid-State Lithium Metal Batteries Towards Practical Conditions

Solid-state lithium metal batteries (SSLMBs) are promising next-generation high-energy rechargeable batteries. However, the practical energy densities of the reported SSLMBs have been significantly overstated due to the use of thick solid-state electrolytes, thick lithium (Li) anodes, and thin cathodes. Here, a high-performance NASICON-based SSLMB using a thin (60 µm) Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 (LAGP) electrolyte, ultrathin (36 µm) Li metal, and high-loading (8 mg cm -2 ) LiFePO 4 (LFP) cathode is reported. The thin and dense LAGP electrolyte prepared by hot-pressing exhibits a high Li ionic conductivity of 1 × 10 -3 S cm -1 at 80 °C. The assembled SSLMB can thus deliver an increased areal capacity of ≈1 mAh cm -2 at C/5 with a high capacity retention of ≈96% after 50 cycles under 80 °C. Furthermore, it is revealed by synchrotron X-ray absorption spectroscopy and in situ high-energy X-ray diffraction that the side reactions between LAGP electrolyte and LFP cathode are significantly suppressed, while rational surface protection is required for Ni-rich layered cathodes. This study provides valuable insights and guidelines for the development of high-energy SSLMBs towards practical conditions.

25 ENERGY STORAGE↗
DOE OSTI2021

Solid-State Synthesis of Highly Dispersed Nitrogen-Coordinated Single Iron Atom Electrocatalysts for Proton Exchange Membrane Fuel Cells

Fe–N–C with atomically dispersed Fe single atoms is the most promising candidate to replace platinum for the oxygen reduction reaction (ORR) in fuel cells. However, the conventional synthesis procedures require quantities solvents and metal precursors, sluggish adsorption process, and tedious washing, resulting in limited metal doping and uneconomical for large-scale production. Here, for the first time, Fe 2 O 3 is adopted as the Fe precursor to derive abundant single Fe atoms dispersed on carbon surfaces. The Fe–N–C catalyst synthesized by this simple method shows an excellent ORR activity with half-wave potentials of 0.82 and 0.90 V in acidic and alkaline solutions, respectively. A single fuel cell with an optimized Fe–N–C cathode shows a high peak power density of 0.84 W cm –2 . The solid-state transformation synthesis method developed in this study may shed light on mass production of single-atom-based catalysts.

25 ENERGY STORAGE↗
DOE OSTI2021

Ultra-high-voltage Ni-rich layered cathodes in practical Li metal batteries enabled by a sulfonamide-based electrolyte

By increasing the charging voltage, a cell specific energy of >400 Wh kg-1 is in principle achievable with LiNi0.8Mn0.1Co0.1O2 in lithium-metal batteries (LMBs). However, stable cycling of high-nickel cathodes at ultra-high voltages is extremely challenging. Here we report that a rationally designed sulfonamide-based electrolyte enables stable cycling of commercial LiNi0.8Co0.1Mn0.1O2 with a cut-off voltage up to 4.7 V in LMBs. In contrast to commercial carbonate electrolytes, the electrolyte not only suppresses side reactions, intergranular cracking, transition-metal dissolution, and impedance growth on the cathode side, but also enables highly reversible Li metal stripping and plating leading to compact morphology and low pulverization. Our LMB delivers a specific capacity >230 mAh g-1 and an average Coulombic efficiency >99.65% over 100 cycles. Even under harsh testing conditions, the 4.7 V LMB can retain >88% capacity for 90 cycles, demonstrating significant advances in practical LMBs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Evoking ordered vacancies in metallic nanostructures toward a vacated Barlow packing for high-performance hydrogen evolution

Metallic nanostructures are commonly densely packed into a few packing variants with slightly different atomic packing factors. The structural aspects and physicochemical properties related with the vacancies in such nanostructures are rarely explored because of lack of an effective way to control the introduction of vacancy sites. Highly voided metallic nanostructures with ordered vacancies are however energetically high lying and very difficult to synthesize. Here, we report a chemical method for synthesis of hierarchical Rh nanostructures (Rh NSs) composed of ultrathin nanosheets, composed of hexagonal close-packed structure embedded with nanodomains that adopt a vacated Barlow packing with ordered vacancies. The obtained Rh NSs exhibit remarkably enhanced electrocatalytic activity and stability toward the hydrogen evolution reaction (HER) in alkaline media. Theoretical calculations reveal that the exceptional electrocatalytic performance of Rh NSs originates from their unique vacancy structures, which facilitate the adsorption and dissociation of H 2 O in the HER.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A high-energy and long-cycling lithium–sulfur pouch cell via a macroporous catalytic cathode with double-end binding sites

Lithium-sulfur batteries are attractive alternatives to lithium-ion batteries because of their high theoretical specific energy and natural abundance of sulfur. However, the practical specific energy and cycle life of Li-S pouch cells are significantly limited by the use of thin sulfur electrodes/flooded electrolytes and polysulfides shuttle/Li metal degradation, respectively. In this work we propose a cathode design concept to achieve good Li-S pouch cell performances. The cathode is composed of uniformly embedded ZnS nanoparticles and Co-N-C single-atom catalyst to form double-end biding sites inside a highly oriented macroporous host, which can effectively immobilize and catalytically convert polysulfides intermediates during cycling, thus eliminating the shuttle effect and lithium metal corrosion. The ordered macropores enhance ionic transport under high sulfur loading by forming sufficient catalyst/conductive support/electrolyte triple-phase boundaries. This prevents the formation of inactive sulfur (dead sulfur). Our cathode structure shows improved performances in a pouch cell configuration under high sulfur loading and lean electrolyte operation. An Ah-level pouch cell with only 100% lithium excess can deliver a cell specific energy of > 300 Wh kg –1 with a Coulombic efficiency >95% for 80 cycles.

25 ENERGY STORAGE↗
DOE OSTI2020

Probing the Thermal-Driven Structural and Chemical Degradation of Ni-Rich Layered Cathodes by Co/Mn Exchange

The intrinsic poor thermal stability of layered LiNi x Co y Mn 1-x-y O 2 (NCM) cathodes and the exothermic side reactions triggered by the associated oxygen release are the main safety threats for their large-scale implantation. In NCM family, it is widely accepted that Ni is the stability troublemaker, while Mn has long been considered as a structure stabilizer, whereas the role of Co remains elusive. Here, via Co/Mn exchange in Ni-rich LiNi 0.83 Co 0.11 Mn 0.06 O 2 cathode, we demonstrate that, the chemical and structural stability of the deep delithiated NCM cathodes are significantly affected by Co, rather than the widely reported Mn. Operando synchrotron X-ray characterization coupling with in situ mass spectrometry reveal that the Co 4+ reduces prior to the reduction of Ni 4+ , and could thus prolong the Ni migration by occupying the tetrahedra sites, and hence postpone the oxygen release and thermal failure. In contrast, the Mn itself is stable, but barely stabilizes the Ni 4+ . Our results highlight the importance of evaluating the intrinsic role of compositional tuning on Ni-rich/Co-free layered oxide cathode materials to guarantee the safe operation of high-energy Li-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Durable hybrid electrocatalysts for proton exchange membrane fuel cells

The low durability of carbon-based non-precious metal electrocatalysts hinders their practical applications in proton exchange membrane fuel cells (PEMFCs). In this study, we rationally design a hybrid Pt-Fe-N-C electrocatalyst with unprecedented durability. It consists of abundant Pt and Fe single atoms homogeneously dispersed on the nitrogen-doped carbon support and a small amount of Pt-Fe alloy nanoparticles. A PEMFC with Pt-Fe-N-C as the cathode shows a larger peak power density (0.75 W cm -2 ) than that with Fe-N-C as the cathode (0.50 W cm -2 ). The remarkable durability of Pt-Fe-N-C is reflected from no noticeable drop in the half-wave potential after 70000 potential cycles between 0.6 and 1.0 V in the liquid cell, and 80% current retention after 85 h of potential hold at 0.4 V in the fuel cell. This work demonstrates the feasibility of improving the durability of Fe-N-C material via ultra-low Pt doping and makes non-precious metal electrocatalysts be close to achieving commercial metrics.

25 ENERGY STORAGE↗