Search NASA⌕ Search

Engineering topics

Ian M. Howat

Publications and source records attributed to Ian M. Howat.

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Applications of ArcticDEM for measuring volcanic dynamics, landslides, retrogressive thaw slumps, snowdrifts, and vegetation heights

Topographical changes are of fundamental interest to a wide range of Arctic science disciplines faced with the need to anticipate, monitor, and respond to the effects of climate change, including geohazard management, glaciology, hydrology, permafrost, and ecology. This study demonstrates several geomorphological, cryospheric, and biophysical applications of ArcticDEM – a large collection of publicly available, time-dependent digital elevation models (DEMs) of the Arctic. Our study illustrates ArcticDEM's applicability across different disciplines and five orders of magnitude of elevation derivatives, including measuring volcanic lava flows, ice cauldrons, post-failure landslides, retrogressive thaw slumps, snowdrifts, and tundra vegetation heights. We quantified surface elevation changes in different geological settings and conditions using the time series of ArcticDEM. Following the 2014–2015 Bárðarbunga eruption in Iceland, ArcticDEM analysis mapped the lava flow field, and revealed the post-eruptive ice flows and ice cauldron dynamics. The total dense-rock equivalent (DRE) volume of lava flows is estimated to be (1431 ± 2) million m 3 . Then, we present the aftermath of a landslide in Kinnikinnick, Alaska, yielding a total landslide volume of (400 ± 8) × 103 m 3 and a total area of 0.025 km 2 . ArcticDEM is further proven useful for studying retrogressive thaw slumps (RTS). The ArcticDEM-mapped RTS profile is validated by ICESat-2 and drone photogrammetry resulting in a standard deviation of 0.5 m. Volume estimates for lake-side and hillslope RTSs range between 40,000 ± 9000 m 3 and 1,160,000 ± 85,000 m 3 , highlighting applicability across a range of RTS magnitudes. A case study for mapping tundra snow demonstrates ArcticDEM's potential for identifying high-accumulation, late-lying snow areas. The approach proves effective in quantifying relative snow accumulation rather than absolute values (standard deviation of 0.25 m, bias of −0.41 m, and a correlation coefficient of 0.69 with snow depth estimated by unmanned aerial systems photogrammetry). Furthermore, ArcticDEM data show its feasibility for estimating tundra vegetation heights with a standard deviation of 0.3 m (no bias) and a correlation up to 0.8 compared to the light detection and ranging (LiDAR). The demonstrated capabilities of ArcticDEM will pave the way for the broad and pan-Arctic use of this new data source for many disciplines, especially when combined with other imagery products. The wide range of signals embedded in ArcticDEM underscores the potential challenges in deciphering signals in regions affected by various geological processes and environmental influences.

Chunli Dai↗
NASA NTRS2022

Quantifying mass flows at Mt. Cleveland, Alaska between 2001 and 2020 using satellite photogrammetry

Measuring eruption volume provides constraints on the magma supply rate and plumbing systems and therefore is a critical component for monitoring volcanoes. We use ArcticDEM—a large collection of time-dependent digital elevation models (DEMs) derived from satellite stereo-photogrammetry — to construct a first-of-its-kind measurement of the volumes of recent mass flows at Mount Cleveland, Alaska. We quantify the volume of the products of the 2001 eruption (the largest in the past half-century) as (54.8 ± 0.5) × 10 -6 m -3 covering a total area of 5.09 km -2 . The total volume of material loss at the summit crater is (0.67 ± 0.02) × 10 -6 m -3 , which is likely caused by later explosions and collapses of the shallow magma chamber. The total eruptive volume between 2017 and 2020 is (0.086 ± 0.002) × 10 -6 m -3 . Elevation changes associated with lahars are variable. On the upper northern slopes of the volcano, the lahar channels were almost exclusively erosive, suggesting that lahars originating at the summit eroded and entrained loose materials high on the cone. In general, lahar deposits were thickest near their toes, with some reaching ~20 m thickness.

Chunli Dai↗
NASA NTRS2020

Characterization of the 2008 Phreatomagmatic Eruption of Okmok From ArcticDEM and InSAR: Deposition, Erosion, and Deformation

Okmok volcano, one of the most active volcanoes in the Aleutian Islands, erupted between 12 July and 19 August 2008 and produced a new tephra cone (Ahmanilix) up to 253 m high. A coeruptive deposit thickness map and the posteruptive elevation change rate map are generated for this phreatomagmatic eruption using the new, high-resolution (2 m) digital elevation model (DEM) time series provided by ArcticDEM. The total dense rock equivalent (DRE) volume over the proximal deposit field classified from the elevation change map is estimated as 0.147 ± 0.001 km 3 DRE (bulk volume of 0.453 ± 0.003 km 3 ). Combined with the distal deposit volume derived from field measurements, the total DRE is 0.25 km 3 (bulk volume of 0.76 km 3 ). The estimated erosion rate is up to −15 ± 3 m/year along the flanks of Ahmanilix, and the redeposition rate is about 1 ± 0.3 m/year at the base and 6 ± 1 m/year within the center of Ahmanilix. The surface elevation change also reveals a large ground surface collapse that disrupted the old Cone D lava bench, with a total collapse area of 0.15 km2 and a volume of (7.1 ± 0.4) × 10−3 km 3 . We also produce a coeruptive deformation map from satellite interferometric synthetic aperture radar (InSAR) using topography from both ArcticDEM and the Shuttle Radar Topography Mission (SRTM) and compare the results. Finally, based on historical eruption volumes, the magma supply rate at Okmok is estimated as (1.77 ± 0.1) × 10−3 km 3 /year.

Chunli Dai↗