Search NASA⌕ Search

Engineering topics

Ilevbare, Gabriel O.

Publications and source records attributed to Ilevbare, Gabriel O..

Electrodialysis: An effective methodology to purify the leachate of spent Li-ion batteries

The electrification of transportation and the transition of society towards low or net-zero carbon emissions has led to a skyrocketing global demand for Li-ion batteries. After a service life of three to ten years, Li-ion batteries have less than 80 % of their initial capacities and draw near to the end of their lives for practical utilization. Due to potential supply chain shortages and the value embodied in Li-ion batteries, it is imperative to recycle them, to recover the materials, and to improve the circularity and the sustinability of the industry. How to cost-effectively purify spent batteries while reducing time, energy, and waste emissions is a challenge faced by Li-ion battery recyclers. The first electrochemical membrane reactor reported in our group hasa high selectivity towards lower Cu 2+ , Al 3+ and Fe 3+ ions (<5 ppm) and retains >95% of the Ni 2+ , Co 2+ and Mn 2+ ions in the leachate. An advanced electrochemical membrane reactor was developed in this study. Further, not only does the new reactor have the same selectivity as the original reactor, but other advantages including a faster leachate processing rate (up to 10X faster). The advanced reactor can also directly generate acid at the anode side; eliminating the reactor restoration step. The prominent advantages that this electrodialysis technology has over chemical-precipitation methods include: (1) ion recovery efficiencies do not diminish after removing the impurities, Ni 2+ , Co 2+ and Mn 2+ , even at a higher initial Ni 2+ ion concentrations; in comparison, chemical precipitation has Ni 2+ , Co 2+ and Mn 2+ ion recovery efficiencies reduced significantly when the initial Ni 2+ , Co 2+ and Mn 2+ ion concentrations increase. (2) electrodialysis does not change the concentrations of Ni 2+ , Co 2+ and Mn 2+ ions significantly, but chemical precipitation could reduce Ni 2+ and Co 2+ ions to less than half of their initial values. Through electro-dialyzing the leachate, the H 2 evolution reaction mechanism was found to switch from the Volmer-acid Heyrovsky mechanism to the Volmer-alkaline Heyrovsky mechanism at a pH of around 3.7.

25 ENERGY STORAGE↗

Methodology for Thermodynamic Analysis Coupled with Computational Fluid Dynamics Modeling for Casting a Novel Aluminum–Cerium Alloy

In this paper, we present the results of computational fluid dynamics (CFD) analysis to assess castability, porosity, molten metal fluidity and other technological properties of a new Al-Ce alloy. A thermodynamic analysis of a new Al-Ce alloy is done to obtain the physical properties as a function of temperature across both solid and liquid phases. These properties are then used to build the CFD of model the full casting process from initial pouring through to final solidification of the part, here an example of a heavy duty mor mount is used. While several excellent commercial CFD codes exists this process shows that CFD can be used to assess the capability of the alloy to properly fill the mold, as well as give predictions where scattered porosity or large-scale defects may occur in the casting. Further, unlike the commercially available software (e.g., ProCAST, SOLIDCast , MAGMASOFT®) the complex 3D-analysis of the stress / strain fields in cast parts is not performed at this time. However, the availability of free software for assessing the required thermodynamic / thermo-physical properties of new alloys (OpenCALPHAD) and CFD codes such as OpenFOAM® makes the developed option attractive and economical, especially for the analysis of new Al-Ce alloys, for which the available data does not exist.

36 MATERIALS SCIENCE↗

Concurrent Precipitation of Nb(C,N) and Metastable M 23 C 6 in Alloy 347H at 700°C and 750°C: Computer Simulations and Comparison to Experiment

Here, we present our results for the concurrent precipitation of metastable M 23 C 6 , Nb(C,N) secondary precipitates, and the Nb(C,N) primary crystals in 347H austenitic stainless steel. For precipitation modeling, we have accounted for the elastic contribution to interfacial energy, and for the Fe-spin-polarization for NbC/Fe and M 23 C 6 /Fe interfacial energy values: for NbC/Fe ~ 0.63 J/m 2 . For M 23 C 6 precipitates, an error function was used to describe the interfacial energy growth with particle size. In precipitation simulations, the average size of the primary Nb(C,N) particles remained ~ 1 μm at 700°C and ~ 0.3 μm at 750°C. The M 23 C 6 precipitates at 750°C dissolved after 120 h (our simulations) compared to 300 h (experiments). The Nb(C,N)/Fe interfacial energy was not affected by the nitrogen additions. With these modifications, reasonable agreement with the available experimental data was obtained, which allows using them in the development of the 2nd-phase particle-informed creep theory.

36 MATERIALS SCIENCE↗

Request for Information on Establishing a New Manufacturing Institute (DE-FOA-0002564)

Deep decarbonization of major industries such as metals manufacturing requires extensive process integration and controls to manage feedstocks, side reactions, heat, water, and waste streams. The scale of the energy and capital investment requires that process integration be validated to a high level of confidence with no bias. Industries such as steel production have very thin profit margins. Therefore, lack of confidence in process integration, product quality, and economics is a major deterrence to changes in manufacturing capital investment. Public sector investment in reconfigurable pilot testbeds and a first-of-a-kind plant would be necessary to de-risk technical and financial barriers prior to industry-wide buildout. DOE should consider a National Lab-led hub for the testbeds. Lab testbeds could be utilized in campaigns and allow multiple industrial partners to evaluate and validate technologies prior to making major capital investments.

08 HYDROGEN↗