Search NASA⌕ Search

Engineering topics

Im, Kyungjae

Publications and source records attributed to Im, Kyungjae.

A new apparatus for the concurrent measurement of friction and permeability evolution in fault gouge

Here we introduce a new miniature double direct shear (mini-DDS) apparatus, housed within a standard-triaxial (TEMCO) pressure vessel, capable of concurrently measuring the evolution of frictional strength, stability, healing and along-fault permeability under in situ conditions of stress and temperature. The apparatus accommodates gouge samples (25 mm × 32 mm) and intact rock samples with confining and shear stresses and pore pressures up to ~26 MPa. Permeability may be measured with applied flow rates ranging from 1.67 × 10 -11 to 3.6 × 10 -6 m 3 /s to a flow accuracy of 0.5% representing a lower bound of permeability >2.2 × 10 -18 m 2 . Sliding velocities are in the range 0.1 μm/s to 0.67 cm/s with a frame stiffness of 0.067 kN/μm. We describe protocols and procedures for calibration and experiments and note the potential of the apparatus for both rapid and extended-duration measurements of friction-permeability evolution and healing. The apparatus returns measurements of friction and stability of reference materials of F110 quartz consistent with the literature while additionally allowing the concurrent measurement of permeability. Permeability of F110 quartz evolves in slide-hold-slide (SHS) experiments with increases during holds and decreases during subsequent slides. These observations are consistent with grain crushing and resultant wear products that reduce that permeability by clogging during slides with unclogging of the major fluid channels occurring during shearing.

58 GEOSCIENCES↗

FRICTION AND PERMEABILITY EVOLUTION OF FRACUTRES AND FAULTS DURING STATIC REPOSE AND DYNAMIC REACTIVATION

The co-evolution of fault/fracture friction and permeability represent important science/engineering challenges impacting natural and engineered systems. Friction directly controls the characteristics of natural fault slip, including inter-seismic healing, slow creep and earthquake rupture. Permeability evolution during fault slip and repose illuminates our understanding of perturbations to the earthquake-modulated natural hydraulic system and of subsurface engineering in recovering both shale gas and geothermal energy and in the safe subsurface sequestration of CO2. However, mechanisms controlling the evolution of friction and permeability during slow slip, fast rupture and inter-event repose are not clearly understood. For instance, the evolution of stick-slip amplitudes and recurrence, the role of inertia and its influence on frictional stability and the interdependence of these processes remain unclear. Furthermore, mechanisms of permeability evolution during the earthquake cycle (repose through rupture) are also poorly understood since they are influenced in a complex way by chemo-mechanical effects such as elastic/plastic compaction, shear comminution, mechanical dilation, pressure solution and stress corrosion. In this study, we explore fracture friction and permeability evolution during static and dynamic reactivation using both numerical and experimental approaches. This is described in the four chapters of this dissertation.

58 GEOSCIENCES↗

Cyclic Permeability Evolution During Repose Then Reactivation of Fractures and Faults

Abstract Cyclic growth and decay of permeability in fractures is explored during repeated reactivation and repose of saw‐cut fractures of Green River shale. These slide‐hold‐slide experiments are supported by measurements of fracture normal deformation and optical surface profilometry. Overall, we observe continuous permeability decay during repose (holds) and significant permeability enhancement during slow reactivation (slide). The permeability decay is accompanied by fault compaction. Both hydraulic aperture change (Δ b h ) and measured compaction (Δ b s ) are consistent with time‐dependent power law closure with a power exponent of ~0.2–0.4. These dual compaction magnitudes are positively correlated but Δ b h > Δ b s in late stage holds. Permeability enhancement during reactivation is typically also accompanied by fault dilation. However, we also observe some cases where hydraulic aperture change decouples from the measured deformation, conceivably driven by mobilization of wear products and influenced by the development of flow bottlenecks. Pretest and posttest surface profiles show that the surface topography of the fractures is planed down by shear removal. The shear removal is significant with initial laboratory prepared surface (~10 μm of aperture height) but less significant following consecutive reactivations (~2 μm). The flattened surfaces retain small‐scale, ~10–20 μm wavelength, roughness. Flow simulations, constrained by the surface topography and measured deformation, indicate that small‐scale roughness may control permeability at flow bottlenecks within a dominant flow channel. These results suggest cycles of permeability creation and destruction are an intrinsic component of the natural hydraulic system present in faults and fractures and provide an improved mechanistic understanding of the evolution of permeability during fault repose and reactivation.

Im, Kyungjae↗

Geophysical and Mineralogical Controls on the Rheology of Fracture Slip and Seal Breaching (Final Report)

This work explores the geophysical and mineralogical controls on the rheology of fractures and faults to define the modes of permeability evolution and the potential for the breaching of seals for subsurface reservoirs. In particular, the work is arranged to determine the dynamic response of faults to shear reactivation (Parts I-III), their post slip and inter-seismic healing (Parts IV-V), their response to chemically reactive alteration (Parts VI-VII) and then upscaling via digital rock physics models (Parts IIX-XI). The work first defines the principal controls on frictional strength and stability in caprocks and unconventional reservoirs and their consequences for permeability evolution in shales (Part I). This linkage is extended to explore the impact of both mineralogy (Part II) and fracture roughness (Part III) on permeability evolution and to link this to the frictional and stability behavior of faults. The important impacts of post-slip healing during interseismic periods is then delineated (Part IV) and constrained using tightly controlled observations of reactivation displacements and permeability measurement (Part V). The role of corrosive fluids in both dissolving (Part VI) and transforming (Part VII) minerals within the fracture walls and cements is then explored, together with impacts on friction, stability and permeability. Finally, process-based models are applied to upscale the friction-stability-permeability response of both gouge-filled faults (Parts VIII and IX) and rough fractures (Part X) together with chemically-driven compaction impacting long-term interseismic sealing (Part XI).

58 GEOSCIENCES↗

The influence of Preslip Sealing on the Permeability Evolution of Fractures and Faults

The evolution of permeability on fractures and faults during the full earthquake cycle is shown to be sensitive to sealing during the repose phase. We explore the combined effect of static loading followed by fracture reactivation on permeability evolution via slide-hold-slide experiments. During the hold periods, permeability exhibits a slow but continuous reduction. The permeability decay is consistent with power law compaction of the aperture coupled with cubic law flow. With increasing hold periods, permeability evolves following reactivation from net reduction to net increase with the magnitude of the permeability change dependent on the hold period. This implies that the tight interlocking of asperities during interseismic repose primes the fault for permeability enhancement following reactivation. The inferred mechanism is via shear dilation with the probable involvement of unclogging. This result identifies that preslip sealing during repose is an essential component in the cyclic permeability evolution throughout the seismic cycle.

58 GEOSCIENCES↗

The Impact of Frictional Healing on Stick-Slip Recurrence Interval and Stress Drop: Implications for Earthquake Scaling: The impact of healing on stick-slip

We report that interseismic frictional healing is an essential process in the seismic cycle. Observations of both natural and laboratory earthquakes demonstrate that the magnitude of stress drop scales with the logarithm of recurrence time, which is a cornerstone of the rate and state friction (RSF) laws. However, the origin of this log linear behavior and short time “cutoff” for small recurrence intervals remains poorly understood. Here we use RSF laws to demonstrate that the back-projected time of null-healing intrinsically scales with the initial frictional state θ i . We explore this behavior and its implications for (1) the short-term cutoff time of frictional healing and (2) the connection between healing rates derived from stick-slip sliding versus slide-hold-slide tests. We use a novel, continuous solution of RSF for a one-dimensional spring-slider system with inertia. The numerical solution continuously traces frictional state evolution (and healing) and shows that stick-slip cutoff time also scales with frictional state at the conclusion of the dynamic slip process θ i (=D c /V peak ). This numerical investigation on the origins of stick-slip response is verified by comparing laboratory data for a range of peak slip velocities. Slower slip motions yield lesser magnitude of friction drop at a given time due to higher frictional state at the end of each slip event. In conclusion, our results provide insight on the origin of log linear stick-slip evolution and suggest an approach to estimating the critical slip distance on faults that exhibit gradual accelerations, such as for slow earthquakes.

58 GEOSCIENCES↗

Geodetic imaging of thermal deformation in geothermal reservoirs - production, depletion and fault reactivation

Here, we investigate thermally induced surface deformation in geothermal systems. To define source mechanisms at depth, we assess the mechanical process of subsurface deformation by assuming a spherically cooled fractured reservoir in an infinite medium and derive relations that define magnitudes of thermal contraction, stress change and permeability evolution. The magnitude of thermal deformation in typical geothermal system is larger than anticipated and suggests two different modalities of surface subsidence – thermal contraction and fault reactivation. Here, surface deformation (vertical displacement, surface tilt and horizontal strain) induced by the two different modalities are assessed with Mogi (contraction) and Okada (slip) models and compared with instrumental sensitivity of high precision surface geodetic tools. Here, we show that 1 year of geothermal operation at 10 MW with a power plant conversion efficiency of 12% can yield ~ 3.0 × 10 4 m 3 of subsurface volume change. For a reservoir at 2000 m depth, this induces ~ 1.7 mm of vertical surface displacement, ~ 800 nano-radians of surface tilt and ~ 900 nano-strains of surface strain. This result implies that typically observed magnitudes of surface subsidence (order of cm/year) are naturally expected in massive (100 MW scale) geothermal operations and observed surface subsidence may largely be the result of thermal contraction. Conversely, thermal unloading can trigger fault reactivation. Analysis with an Okada slip model shows these shear offsets on pre-existing faults can also result in surface deformations of considerable magnitude. Our analysis of field operational data from various geothermal projects suggests that both thermal contraction and slow fault reactivation may contribute to the observed large surface deformation. Comparison of predicted deformation with instrumental sensitivity of high precision surface tools confirms that geodetic signals, especially tilt and strain, are indeed sufficiently large to describe reservoir evolution and to potentially deconvolve reservoir parameters of interest, such as permeability.

15 GEOTHERMAL ENERGY↗

Benchmark Problems of the Geothermal Technologies Office Code Comparison Study

A diverse suite of numerical simulators is currently being applied to predict or understand the performance of enhanced geothermal systems (EGS). To build confidence and identify critical development needs for these analytical tools, the United States Department of Energy, Geothermal Technologies Office has sponsored a Code Comparison Study (GTO-CCS), with participants from universities, industry, and national laboratories. A principal objective for the study was to create a community forum for improvement and verification of numerical simulators for EGS modeling. Teams participating in the study were those representing U.S. national laboratories, universities, and industries, and each team brought unique numerical simulation capabilities to bear on the problems. Two classes of problems were developed during the study, benchmark problems and challenge problems. The benchmark problems were structured to test the ability of the collection of numerical simulators to solve various combinations of coupled thermal, hydrologic, geomechanical, and geochemical processes. This class of problems was strictly defined in terms of properties, driving forces, initial conditions, and boundary conditions. Study participants submitted solutions to problems for which their simulation tools were deemed capable or nearly capable. Some participating codes were originally developed for EGS applications whereas some others were designed for different applications but can simulate processes similar to those in EGS. Solution submissions from both were encouraged. In some cases, participants made small incremental changes to their numerical simulation codes to address specific elements of the problem, and in other cases participants submitted solutions with existing simulation tools, acknowledging the limitations of the code. The challenge problems were based on the enhanced geothermal systems research conducted at Fenton Hill, near Los Alamos, New Mexico, between 1974 and 1995. The problems involved two phases of research, stimulation, development, and circulation in two separate reservoirs. The challenge problems had specific questions to be answered via numerical simulation in three topical areas: 1) reservoir creation/stimulation, 2) reactive and passive transport, and 3) thermal recovery. Whereas the benchmark class of problems were designed to test capabilities for modeling coupled processes under strictly specified conditions, the stated objective for the challenge class of problems was to demonstrate what new understanding of the Fenton Hill experiments could be realized via the application of modern numerical simulation tools by recognized expert practitioners.

15 GEOTHERMAL ENERGY↗

Surface and Subsurface Geodesy Combined with Active Borehole Experimentation for the Advanced Characterization of EGS Reservoirs

We explore the utility of combining active downhole experimentation with borehole and surface geodesy to determine both the characteristics and evolving state of EGS reservoirs during stimulation through production. The study is divided into two parts. We demonstrate the feasibility of determining in situ reservoir characteristics of reservoir size, strain and fracture permeability and their dependence on feedbacks of stress and temperature using surface and borehole geodetic measurements (Part I). We then define the opportunity to apply the unique hydraulic pulse protocol (HPP) borehole tool to evaluate reservoir state. This can be accomplished by monitoring and co-inverting measured reservoir characteristics (from the HPP tool) with surface geodetic measurements of deformation, tilt and strain with continuous measurements of borehole-wall strain (via optical fiber and fiber Bragg gratings) and measured flow rates (Part II).

15 GEOTHERMAL ENERGY↗