Engineering topics
Publications and source records attributed to Imbriale, William A..
None given. Paper covers the NASA Deep Space Network (DSN) Goldstone Complex in Mojave, California, and their beam-waveguide (BWG) antenna complex. They discuss system noise temperature,its major contributor, and its correction.
Various design techniques used for beam waveguide (BWG) feed systems are characterized. These include the use of gaussian beam, geometrical optics, and physical optics systems. Also introduced is a new technique based upon a conjugate phase matching focal plane technique. Advantages, disadvantages, and range of applicability of each technique is given, In addition, comparisons of computed and measured results from each type of design are presented.
Spatially periodic slots in metal plate make plate appear transparent at frequency of resonance of slots. Appears mostly reflective at high frequencies. Orthogonal slots accommodate circular polarization; one of two orthogonal slots in each pair eliminated if only one known linear polarization needed. Spectral response of plate tailored by choice of dimensions of slots.
Improved method devised for calculating gain of antenna system comprising main reflector and array of feed elements. Method involves much less computation; important advantage when necessary to compute gains repeatedly, with slight variations in design at each iteration, in effort to find optimum design.
Physical optics scattering calculations performed on the NASA Deep Space Network (DSN) 34-meter beam-waveguide antennas at Ka-band (typically five surfaces) requires approximately 12 hours CPU time on a Cray Y-MP2 computer-excessive in terms of resource utilization. The calculations are done two mirrors at a time.
POMESH is computer program capable of predicting performance of reflector antennas. Calculates both farfield patterns and gains by use of physical-optics approximation of equivalent surface currents. Intended for relatively small reflectors. Useful in situations in which surfaces described by irregular data that must be interpolated and in which surface derivatives not known. Flexible and robust. Also calculates near fields and useful for subreflector computations. Written in FORTRAN 77.
During development of a Venetian Blind polarizer, high reflections and substantial pattern deformation were noted. Analysis showed that when the polarizer was illuminated slightly off axis, a degenerate mode was excited. This mode is resonant at the design center frequency, and was the cause of the problems. A design developed using dual vanes has been shown to be free of the problem. It also has greater bandwidth.
Report presents examples to demonstrate validity and utility of method of synthesis of offset dual-shape reflectors. Method of synthesis described by the authors in previous journal article. Current report reviews derivation of partial differential equations and iterative method of numerical solution. Discusses significance of starting point of numerical integration on each reflector surface; this point could be at center, on outer rim, or at interior point. Emphasizes that one of notable attributes of partial differential equations is speed with which they can be solved.
Large beam waveguide (BWG) type ground station antennas are generally designed using analysis which ignores the presence of the metallic tube enclosing the beam waveguide mirrors. The common analysis approaches are physical optics and Gaussian mode analyses. The weakness of these analyses is that they do not shed any light with regards to the effect of the metal tube. In this paper, the first known BWG analysis which considers the presence of the metal tube is presented. Numerical results of a two-mirror system using the new analysis are compared with experiments which have verified the new analysis.
Paper addresses defocusing and diffraction effects important in design of beam waveguide. Phase center of beam waveguide at lower frequency differs from focal point of geometric optics. If antenna system optimized for higher frequency, shift in phase center causes defocusing, with loss of signal at lower frequency. Defocusing caused by diffraction at lower frequencies reduced by shaping input pattern.
Several characteristics of dual offset (DOSR) and symmetric shaped reflectors are examined. Among these is the amelioration of the added cost of manufacturing a shaped reflector antenna, particularly a doubly curved surface for the DOSR, if adjustable panels, which may be necessary for correction of gravity and wind distortions, are also used for improving gain by shaping. The scanning properties of shaped reflectors, both offset and circularly symmetric, are examined and compared to conic section scanning characteristics. Scanning of the pencil beam is obtained by lateral and axial translation of a single point-source feed. The feed is kept pointed toward the center of the subreflector. The effects of power spillover and aperture phase error as a function of beam scanning is examined for several different types of large reflector designs including DOSR, circularly symmetric large f/D and smaller f/D dual reflector antenna systems. It is graphically illustrated that the Abbe-sine condition for improving scanning of an optical system cannot, inherently, be satisfied in a dual-shaped reflector system shaped for high gain and low feed spillover.
The evolution of the largest antenna of the US NASA Deep Space Network (DSN) is described. The design, performance analysis, and measurement techniques, beginning with its initial 64-m operation at S-band (2295 MHz) in 1966 and continuing through the present ka-band (32-GHz) operation at 70 m, is described. Although their diameters and mountings differ, these parabolic antennas all employ a Cassegrainian feed system, and each antenna dish surface is constructed of precision-shaped perforated-aluminum panels that are secured to an open steel framework
Poorer than expected surface reflectivity was observed in an early Tracking and Data Relay Satellite System antenna utilizing a tricot mesh weave. This poor reflectivity was determined to be caused by inadequate electrical contact at wire crossover points. A proper mathematical and numerical approach to assess the impact of wire junctions on reflectivity performance is developed. A mathematical method is presented for computing the surface reflectivity of complex mesh configurations like those on unfurlable-type spacecraft antennas. The method is based on the Floquet mode expansion to establish an integral equation for mesh wire currents. The equation is solved using the method of moments with triangular basis functions. It is observed that it is necessary to give special attention to the junction treatment among different branches of the mesh configurations. A vector junction current approach that resulted in satisfactory solutions for the current is described. The results of numerical simulations are compared against measured data and excellent agreement is observed.
The application of the theory of the synthesis of offset dual-shaped reflectors to the design of compact ranges is examined. The object of the compact range is to provide a uniform plane wave with minimum amplitude and phase ripple over as large a volume as possible for a given size reflector. Ripple can be lowered by reducing the edge diffraction from the reflector producing the plane wave. This has been done either by serrating or rolling the edge. An alternative approach is to use dual offset-shaped reflector synthesis techniques to produce a reflector aperture distribution that is uniform over most of the aperture, but with a Gaussian taper near the edge. This approach can be used together with rolling and/or serration if desirable. The amount of phase and amplitude ripple obtained with two different dual-shaped reflector designs is studied as a function of position in the plane wave zone and reflector size in wavelengths. The amount of both transverse and longitudinal (z-component) cross polarization is studied.
In an earlier paper by Galindo-Israel et al. (1987), the geometrical optics (GO) principles, constraints, and requirements of the dual- and single-offset-shaped reflector synthesis problem were collected and developed into a set of nonlinear first-order PDEs. An extension of the methods by which solutions to the PDEs can be obtained is presented, together with several case examples. These examples are independently analyzed by GO and physical optics diffraction methods. The starting point for the integration over each reflector can be taken on the outer rim, at the center, or at an intermediate point-the intermediate starting point being the more general case. The utility of the speed of this synthesis method is demonstrated. For example, the program utilized completes a synthesis in less than 45 s on a 386/20 personal computer and within a fraction of a second on a mainframe Cray. This makes practical the incorporation of the synthesis into a search algorithm that can optimize one or more parameters of the reflector system. As an example, the optimization of the mapping equations for low cross polarization is discussed.
Results are presented of an investigation on improvements in a geometrical optics (GO) design of a beam-waveguide antenna for operation at multiple frequency bands. Improvements might be possible by changing the design of the lower-frequency input pattern to the beam waveguide. The effects of amplitude and phase shaping the input pattern have been studied with an aperture diffraction model. Accurate vector near-field computations were made rapidly with a spherical wave expansion of the input and scattered fields. Numerical results indicate that for aperture sizes of less than 30 wavelengths, there is insufficient control on defocusing due to amplitude and phase shaping. Design tradeoffs on spillover loss and defocusing are possible by changing the amplitude and phase distribution of the input wavefront for larger size apertures.
Report presents study of some sources of error in analysis, by geometric theory of diffraction (GTD), of performance of high-gain, dual-shaped antenna reflector. Study probes into underlying analytic causes of singularity, with view toward devising and testing practical methods to avoid problems caused by singularity. Hybrid physical optics (PO) approach used to study near-field spillover or noise-temperature characteristics of high-gain relector antenna efficiently and accurately. Report illustrates this approach and underlying principles by presenting numerical results, for both offset and symmetrical reflector systems, computed by GTD, PO, and PO/GO methods.
An algorithmic procedure for the synthesis of planar array feeds for paraboloidal reflectors is described which simultaneously provides electronic correction of systematic reflector surface distortions as well as a Vernier electronic beamsteering capability. Simple rules of thumb for the optimum chioce of planar array feed configuration (i.e., the number and type of elements) are derived from a parametric study made using the synthesis procedure. A number of f/D ratios and distortion models were examined that are typical of large paraboloidal reflectors. Numerical results are presented showing that, for the range of distortion models considered, good on-axis gain restoration can be achieved with as few as seven elements. For beamsteering to +/- 1 beamwidth (BW), 19 elements are required. For arrays with either 7 or 19 elements, the results indicate that the use of high-aperture-efficiency elements (e.g., disk-on-rod and short backfire) in the array yields higher system gain than can be obtained with elements having lower aperture efficiency (e.g., open-ended waveguides). With 37 elements, excellent gain and beamsteering performance to +/- 1.5 BW are obtained independent of the assumed effective aperture of the array element. An approximate expression is derived for the focal-plane field distribution of the distorted reflector. Contour plots of the focal-plane fields are also presented for various distortion and beam scan angle cases. The results obtained show the effectiveness of the array feed approach.