Engineering topics

Isbill, Sara

Publications and source records attributed to Isbill, Sara.

5 records

DOE OSTI2024

Product-specific kinetics reveal effect of epoxy crystallization on thermoset thermal degradation

Crystallization is a common problem for epoxy resins, which are ubiquitous in industrial and commercial use. Integration of crystallized epoxy monomers into cured thermosets has been shown to alter the thermosets’ final mechanical properties. However, no studies have investigated the impact of these crystals on the thermal stability of the thermoset. Here we investigate the degradation kinetics of a bisphenol F–based epoxy thermoset with and without crystallized monomers using Product-Specific Kinetic (PSK) analysis coupled with Evolved Gas Analysis-Mass Spectrometry (EGA-MS). PSK analysis revealed significant differences in evolved product ion kinetics, suggesting changes in the degradation kinetics between thermoset configurations. Further, it was concluded that early stages of degradation are influenced most by crystal presence due to the high concentration of unreacted epoxy monomers and lower cross-linking density of the cured network. After post-cure annealing, significant changes are observed in the degradation kinetics of thermosets without crystal inclusions. Conversely, post-cure annealing procedures of crystal integrated thermosets showed little change in the thermoset degradation kinetics across all conversion extents. These findings suggest that post-cure annealing of thermosets with crystals present at the onset does not alter the cross-linking density of the polymer network enough to significantly change the degradation kinetics. We hypothesize this is because the excess monomers from the melted crystals are unable to find suitable reaction sites for complete binding into the polymer network, which has direct implications for the material properties and final thermal stability of the thermoset.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Fluorescent aggregate structure revealed in bisphenol F epoxy thermoset

Bisphenol F (BPF) epoxy resin is a prepolymer component of thermosets used in construction of reinforced carbon fiber composites (RCFC). The fluorescence of this resin can provide information about chemical and structural alterations of the thermoset from thermal or mechanical damage. While some work has investigated the fluorescence spectra of bisphenol A epoxy resin, a structural analog of BPF, none have studied BPF. The purpose of this study is to investigate the baseline fluorescence spectra of the BPF epoxy resin for features that could be utilized for monitoring damage and structural alterations. Bisphenol F epoxy resin was found to have two emission peaks with a broad peak centered at 410 nm and a sharp peak centered at 550 nm. The broad emission peak was identified as the fluorescence from BPF epoxy monomer while the sharp emission peak was found to be from an aggregate structure present in the epoxy resin. It is hypothesized that this structure is an H-aggregate based on the emission features and structural stability of the aggregate compared to the alternative J-aggregate which was determined via density functional theory calculations. The H-aggregate was found to persist into one of the cured thermoset formulations evaluated but was lost when exposed to elevated temperatures below thermal degradation of the thermoset. This loss of aggregate structure was due to polymer network rearrangement. This new fluorescence signature can be used as an indicator of polymer network rearrangement from thermal exposure which may alter the expected material performance and precede thermal degradation.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Thermally Induced Structural Transitions in Epoxy Thermoset Polymer Networks and Their Spectroscopic Responses

The polymer network structure of epoxy thermosets plays a significant role in its final material properties. However, the effects of mild thermal exposure on these network structures are poorly studied. In this work, wide-angle X-ray scattering was used to investigate the polymer network structure of two epoxy thermosets: homopolymerized bisphenol A (BPA) epoxy resin and BPA epoxy resin cured with a polyether amine hardener (BPA/T-403). Using density functional theory and wide-angle X-ray scattering, insights into the polymer network structure were obtained. Diffraction features were determined to originate from hardener-to-hardener molecular distance, perpendicular π–π stacking of aromatic p-phenylene rings, and the average carbon–carbon distance in the polymer. Thermal exposure was found to permanently alter these structural features for both thermosets, with an increase in the π–π stacking distance. Homopolymerized BPA had an additional decrease in the hardener-to-hardener distance. These structural alterations were found to be detectable using Fourier transform infrared spectroscopy and Raman spectroscopy, with changes in the hardener-to-hardener distance having the largest variations in the resulting spectra specifically at the aromatic and ether frequencies.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Computational investigations of Dienes defect- and vacancy-induced changes in the electronic and vibrational properties of carbon fiber structural units

Carbon fiber (CF) is a promising lightweight alternative to steel and is of significant interest for energy applications. As CF continues to find new uses and is exposed to new external conditions, a noninvasive method of monitoring its structural integrity is critical. Raman spectroscopy is a commonly used method for this monitoring; however, it is highly inferential, and the interpretation of the data is not always straightforward. In this work, we perform density functional theory (DFT) calculations to investigate changes in the vibrational properties of CF structural units (i.e., graphene and graphite) caused by monovacancy and Dienes defects as a foundation for modeling more complex defects that move our model toward that of realistic CF. Using large computational supercells, we can understand how these defects change the electronic structure and vibrational properties of graphene and graphite for interdefect distances near those of the lower experimental limit. The monovacancy opens an electronic bandgap at the K point. Although no such electronic gap is opened by the Dienes defect, both defects introduce flat defect bands near the Fermi energy. The Dienes defect creates long-range deviations of the phonons, leading to substantial broadening of the highest frequency optical modes in the band structure compared to that of the pristine material. In contrast, the phonon changes caused by the monovacancy are short range, and only minor changes in the band structure or phonon density of states were observed. These findings can assist in the interpretation of experimental results by providing atomic-scale insight into key electronic and vibrational features.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Inelastic Neutron Spectra of Uranium Tetrafluoride Hydrate, UF 4 (H 2 O) 2.5

Uranium tetrafluoride hydrate (UFH) is formed by immersing anhydrous UF4 under water for 12 h. UFH is therefore clearly a chemical species of environmental concern, as anhydrous UF4 is an intermediate uranium form in the nuclear fuel cycle. We use inelastic neutron scattering (INS) to probe the full vibrational spectra of UFH and its deuterated analogue in an effort to improve the fundamental understanding of its vibrational spectra. Coupled with density functional theory (DFT) calculations, the first for this compound, and full spectral modeling, we generate the complete vibrational spectra of UFH and compare them to prior optical spectroscopic results. In particular, the combination of DFT with INS allows us to identify multiple distinct chemical environments in the water bending and OH stretching regions. Whereas the water molecules directly bound to the U atoms execute OH stretching around 3600 cm –1 , a second class of H-bonded waters vibrate below 3000 cm –1 , an indicator of strong H bonding. In addition, a class of librational water modes are observed between 400 and 900 cm–1, which themselves can be separated in energy according to their chemical environments. Furthermore, measurements presented herein directly assist in the assignment of certain spectral features in the infrared spectrum and will inform future investigations of UFH for environmental or forensics purposes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗