Experimental Investigation and Characterization of the Thermal Insulating Behavior of Municipal Solid Waste and its Constituents
Not Available
Saha, Nepu (ORCID:0000000340049864)↗
Engineering topics
Islam, Md Tahmid
Publications and source records attributed to Islam, Md Tahmid.
Advanced biorefinery feedstock from non-recyclable municipal solid waste by mechanical preprocessing
Because of accelerated urbanization and the development of a global economy, a large quantity of municipal solid waste (MSW) has been collected and disposed of by the municipalities. Due to this drastic increase in the disposal of MSW, the need for its management is a must to preserve the environment. Currently, approximately 50% of the total MSW generated in the United States has been utilized through various recycling, combustion, and composting technologies, which means the remaining 50% is sent to landfill; this is often known as non-recyclable MSW (nMSW). As this nMSW is physically and chemically heterogenous and contains very high amounts of inorganic material, processing is required prior to using it as a biorefinery feedstock. Thus, this study focused on how mechanical preprocessing advanced the physical and chemical properties of nMSW. The physical and chemical properties were investigated in terms of particle size distribution, bulk density, ultimate and proximate analysis, and the higher heating value (HHV). The combustion properties were examined in terms of ignition temperature, peak heat release rate, and combustion efficiency. Results showed that the variability of physical and chemical properties of nMSW can be reduced by mechanical preprocessing. For example, the variability of the bulk density of the as-received nMSW was approximately 17.3% while it reduced to 5.8% when the sample size was reduced to 2 mm. Similarly, the variability of ash and HHV reduced from 49.2% to 11.0% and 13.4%–4.2%, respectively. Combustion thermograms showed that the size reduction positively improved the combustion properties. For example, 2 mm of spec sample started to ignite approximately 4 times earlier and took 6.5 folds less time to reach the peak heating rate compared to as-received nMSW. Overall, the mechanical preprocessing reduced the variability of physical and chemical properties in addition to the improvement of combustion behavior of the nMSW which is one step forward toward the biorefinery feedstock.
09 BIOMASS FUELS↗
Recent Progress on Emerging Applications of Hydrochar
Hydrothermal carbonization (HTC) is a prominent thermochemical technology that can convert high-moisture waste into a valuable product (called hydrochar) at a relatively mild treatment condition (180–260 °C and 2–10 MPa). With rapidly growing research on HTC and hydrochar in recent years, review articles addressing the current and future direction of this research are scarce. Hence, this article aims to review various emerging applications of hydrochars, e.g., from solid fuel to soil amendment, from electron storage to hydrogen storage, from dye adsorption, toxin adsorption, heavy metal adsorption to nutrient recovery, and from carbon capture to carbon sequestration, etc. This article further provides an insight in the hydrochar’s working mechanism for various applications and how the applications can be improved through chemical modification of the hydrochar. Finally, new perspectives with appropriate recommendations have been made to further unveil potential applications and its improvement through hydrochar and its modified version.
09 BIOMASS FUELS↗
Pretreatment of Biomass by Selected Type-III Deep Eutectic Solvents and Evaluation of the Pretreatment Effects on Hydrothermal Carbonization
Hydrothermal carbonization (HTC) is a novel thermochemical conversion that converts wet biomass into energy dense solid fuel. Residual moisture under subcritical conditions reacts with a lignin-cellulose-hemicellulose matrix with the major reactions being identified as dehydration and decarboxylation. Among other reaction parameters (e.g., temperature, time, pressure), biomass morphology often plays a key role in HTC. The hypothesis of this study was enhancing the porous structure of biomass without significantly affecting biopolymer composition would augment hydrothermal carbonization (HTC). To prove the hypothesis, two type-III deep eutectic solvents (DESs), namely choline chloride:urea (ChCl:Urea, 1:2 mol/mol) and methyltriphenylphosphonium bromide:ethylene glycol (MTPB:EG, 1:4 mol/mol), were studied to pretreat loblolly pine at room temperature and ambient pressure for 1 h. DES pretreatment shows swelling of the biomass, increasing the surface fiber-to-fiber gap length by 52% and 185% for ChCl:Urea and MPTB:EG pretreatments, respectively. The total pore volume remained intact (2.6 × 10 –3 cm 3 /g), although new small pores evolved, and existing pores were abated with DES pretreatment. Hydrochars prepared from DES pretreated loblolly pine showed a high O/C and H/C ratio resulting in a significant increase of energy content (up to 42%) and a decrease of mass yield (up to 50 wt %), indicating an enhancement of HTC severity due to the alteration of surface morphology by DES. Finally, a preliminary process economics revealed that integrated DES pretreatment-HTC would increase fixed capital investment but decrease the cost of operation and manufacturing than the standalone HTC process.
09 BIOMASS FUELS↗
Integration of Air Classification and Hydrothermal Carbonization to Enhance Energy Recovery of Corn Stover
Air classification (AC) is a cost-effective technology that separates the energy-dense light ash fraction (LAF) from the inorganic-rich high ash fraction (HAF) of corn stover. HAF could be upgraded into energy-dense solid fuel by hydrothermal carbonization (HTC). However, HTC is a high-temperature, high-pressure process, which requires additional energy to operate. In this study, three different scenarios (i.e., AC only, HTC only, and integrated AC–HTC) were investigated for the energy recovery of corn stover. AC was performed on corn stover at an 8 Hz fan speed, which yielded 84.4 wt. % LAF, 12.8 wt. % HAF, and 2.8 wt. % below screen particles. About 27 wt. % ash was reduced from LAF by the AC process. Furthermore, HTC was performed on raw corn stover and the HAF of corn stover at 200, 230, and 260 °C for 30 min. To evaluate energy recovery, solid products were characterized in terms of mass yield, ash yield, ultimate analysis, proximate analyses, and higher heating value (HHV). The results showed that the energy density was increased with the increase in HTC temperature, meanwhile the mass yield and ash yield were decreased with the increase in HTC temperature. Proximate analysis showed that fixed carbon increased 18 wt. % for original char and 27 wt. % for HAF char at 260 °C, compared to their respective feedstocks. Finally, the hydrochar resulting from HAF was mixed with LAF and pelletized at 180 bar and 90 °C to densify the energy content. An energy balance of the integrated AC–HTC process was performed, and the results shows that integrated AC with HTC performed at 230 °C resulted in an additional 800 MJ/ton of energy recovery compared to the AC-only scenario.
09 BIOMASS FUELS↗