Engineering topics

Ivanusa, Pavlo

Publications and source records attributed to Ivanusa, Pavlo.

5 records

DOE OSTI2024

Custom ORIGEN Libraries for Tritium Production in Discrete Burnable Absorbers

The ORIGEN module in SCALE is a common method of performing quick depletion and irradiation calculations of various materials in light-water reactors. However, these analyses depend on the neutron spectra in the ARP libraries being accurate for the situation presented. When using insertable burnable absorbers in a LWR with Li-6 in order to produce tritium, the neutron spectrum is highly different than those in the default libraries in ORIGEN, which leads to significant mispredictions in tritium production. Therefore, custom libraries are required, and when comparing to lattice physics codes (CASMO5 and WIMS10) with ORIGEN, using custom libraries is much more accurate than using the default libraries.

Ivanusa, Pavlo↗

DOE OSTI2023

Modeling Non-UO2 Fuel With UNF-ST&DARDS

The U.S. Department of Energy’s Used Nuclear Fuel-Storage, Transportation & Disposal Analysis Resource and Data System (UNF-ST&DARDS) provides an easy-to-use interface to analyze irradiated UO2 fuel by allowing all analysis to be performed within the software and being able to store and use dozens of fuel assembly, canister, and cask designs [1]. However, performing these same analyses with non-UO2 fuel, such as UN or U3Si2, requires more user intervention in the process. This work uses UN, UN-ZrO2, and U3Si2 fuel to demonstrate how to perform criticality analyses in the current versions of UNF-ST&DARDS and how a non-UO2 fuel will compare to UO2. This work is part of a larger effort that also includes shielding and thermal analyses, but they will not be discussed.

Ivanusa, Pavlo↗

DOE OSTI2021

Spent Nuclear Fuel Mechanical Loads in the General Package Drop Scenario

The US Department of Energy Spent Fuel and Waste Science and Technology program is performing research to determine the mechanical loading conditions applied to spent nuclear fuel (SNF) during normal conditions of transportation to inform mechanical tests of SNF and close an important knowledge gap related to the practical disposition of SNF in the US. A recent multi-national collaborative test campaign measured SNF assembly impact response to the 30 cm horizontal package drop scenario, which is a common regulatory basis test of SNF package design. Researchers at Pacific Northwest National Laboratory (PNNL) are using the test data to validate explicit finite element models to calculate the mechanical loads and structural response of spent nuclear fuel assemblies in the as-tested 30 cm horizontal package drop scenario. Once the as-tested package drop model is validated, the next step is to apply the model to the general 30 cm drop scenario, which includes all impact angles, all fuel assembly types, and all burnup conditions. PNNL is developing a damage model that will incorporate the results of finite element parametric studies to establish trends in SNF mechanical loading to various input parameters, like impact orientation and burnup. The damage model will have the capability to estimate mechanical loads for any single set of input parameters, but it will first be used to describe the upper bounds of potential SNF loading in the 30 cm drop scenario. This paper describes PNNL’s progress toward developing the general solution to the problem of spent nuclear fuel mechanical loads in the 30 cm package drop scenario and it describes the next steps in closing the knowledge gap.

Klymyshyn, Nicholas A.↗

DOE OSTI2021

Comparison of Irradiated TRISO Fuel Radioactivity from Multiple Advanced Reactor Designs

The SCALE code system was used to model, deplete, and compare several different TRISO-fueled reactor designs: a helium-cooled prismatic reactor, a helium-cooled pebble-bed reactor (PBR), and a Fluoride-Lithium-Beryllium (FLIBE) molten-salt-cooled PBR. The purpose of this comparison was to understand how differences in the reactor designs affect the radioactivity of the fuel after discharge and whether those differences are significant. First, the various reactor designs were build and depleted in the TRITON module for each design and fuel enrichment. Then, the TRITON outputs were used to create burn-up dependent reactor libraries. These libraries were then used by ORIGEN to determine the activities of discharged fuel for each reactor, which were compared to generic Westinghouse 17x17 fuel. Overall, the results showed that short term decays are dominated by reactors with higher operating powers, and the reactor type, initial fuel enrichment, and maximum burn-up are of only secondary importance. Although this analysis only focuses on activities in becquerels, these dependencies are consistent with the expected behavior of decay heat. However, analysis of long- term time periods post-irradiation shows that the reactor type and maximum burn-up have strong impacts on the activities; initial fuel enrichment has a secondary impact while operating power is inconsequential. These results would be useful for analyses, such as dose assessment and modeling in post- release scenarios; normal fuel handling operations; and spent fuel transport, storage and disposal. Of particular interest, the results in this report show that analyses that focus on spent nuclear fuel of advanced reactors need to consider each parameter carefully. Unsurprisingly, if the correct operating power is not used in short term analyses, the results will not be correct. Perhaps unexpectedly, however, if the correct reactor type is not used, then the long term results will also be incorrect, especially for areas such as permanent disposal. Even though this report focuses on the total activity of nuclear fuel, it provides initial results on the effects of various input parameters and also provides a framework to extend the work into other analyses of spent fuel from advanced reactors, especially those employing TRISO fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Modeling and Analysis for Spent Nuclear Fuel Seismic Testing

Note: This is the final public release version of PNNL-31671 Draft, which was previously released to the sponsor for review. The intent is the public release version will be PNNL-31671. There are no significant changes from the earlier draft version. This unlimited distribution report is the deliverable for M3SF-21PN010202014: Modeling and Analysis for Spent Nuclear Fuel Seismic Testing. This report summarizes the modeling, analysis, and test plan support completed by Pacific Northwest National Laboratory for the spent nuclear fuel dry storage system seismic test plan through May of 2021. Test plan preparation is planned to continue until the seismic test is completed in July of 2022. This report covers preliminary structural dynamic model development and computer-aided design of test hardware. Based on preliminary modeling, the strongest earthquakes under consideration in this test program provide mechanical loading on the spent nuclear fuel that is comparable to the 30 cm cask drop scenario, although the loads do not appear to be strong enough to cause significant permanent deformation of the fuel assembly spacer grids. The potential for grid deformation during the test will be assessed when the proposed shake table motion becomes available. The weakest earthquakes considered in this test are expected to be comparable to the mechanical loads witnessed in the multimodal transportation test of 2017. The horizontal canister system is predicted to provide nearly-uniform loading condition on the fuel assemblies it contains, while the vertical cask system is predicted to cause non-uniform dynamic loads on the fuel assemblies. In the horizontal case, gravity keeps the fuel assemblies in contact with one basket wall surface unless the loads are strong enough to cause a separation. In the vertical case, the fuel assemblies are relatively long and slender, and seismic motion in the anticipated test range is predicted to cause the assemblies to lean, tilt, and impact the basket walls throughout the seismic event. These gap closures are a nonlinear force transmission condition, so the vertical system is expected to have more variation and variability than the horizontal system. While the horizontal system is expected to have a relatively more linear response than the vertical system, there is still the potential for nonlinear behavior in the horizontal system because the fuel assemblies are free to slide, bounce, and impact the basket walls if the seismic loads are strong enough. One major conclusion of this study is that the use of mixed fuel assemblies in the canister will be acceptable. There are differences in overall system response when the mass, center of gravity, or gaps are changed, but the changes in response are within the bounds of a system that contains completely homogeneous fuel assemblies. One important observation is that the loading for each individual fuel assembly within the vertical canister is expected to be different from that of the others because of nonlinearities in the system. The horizontal canister system is expected to have a more uniform and more predictable response than the vertical canister, making variations in fuel assembly characteristics easier to account for. One important recommendation that comes from this modeling work is to repeat some of the strongest shake tests at different angles, particularly for the vertical cask system. Modeling predicts that strong seismic motion will cause the fuel assemblies to close initial gaps and impact the fuel basket walls when the canister is in the vertical cask configuration. Each shake test will impose a pre-defined three-dimensional time history on the cask system.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗