Search NASA⌕ Search

Engineering topics

Iyer, Venkit

Publications and source records attributed to Iyer, Venkit.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

A Wall Correction Program Based on Classical Methods for the National Transonic Facility (Solid Wall or Slotted Wall) and the 14x22-Ft Subsonic Tunnel at NASA LaRC

A Fortran subroutine CMWALL is described, which is an implementation of the collective information from classical methods-based wall corrections. These methods use established closed-form expressions which were developed based on simple linear potential-based methods. This is a simple and rapid tool to calculate corrections due to wall interference in the National Transonic Facility (Solid Wall or Slotted Wall) or the 14x22-Ft Subsonic Tunnel at NASA LaRC. It is designed to be easily implemented in the existing tunnel data reduction programs, either as real-time or post-point. It is however important to realize that the method is based on the simplifying assumptions of linearity, small model and attached flow. The computed results are thus to be viewed as first-cut estimates, to be refined further using more complex methods based on measured wall pressures (known as wall signature methods).

Hemsch, Michael J.↗
NASA NTRS2004

Wall Interference Study of the NTF Slotted Tunnel Using Bodies of Revolution Wall Signature Data

This paper is a description of the analysis of blockage corrections for bodies of revolution for the slotted-wall configuration of the National Transonic Facility (NTF) at the NASA Langley Research Center (LaRC). A wall correction method based on the measured wall signature is used. Test data from three different-sized blockage bodies and four wall ventilation settings were analyzed at various Mach numbers and unit Reynolds numbers. The results indicate that with the proper selection of the boundary condition parameters, the wall correction method can predict blockage corrections consistent with the wall measurements for Mach numbers as high as 0.95.

Iyer, Venkit↗
NASA NTRS2004

Wall Interference Study of the NTF Slotted Tunnel Using Bodies of Revolution Wall Signature Data

This paper is a description of the analysis of blockage corrections for bodies of revolution for the slotted-wall configuration of the National Transonic Facility (NTF) at the NASA Langley Research Center (LaRC). A wall correction method based on the measured wall signature is used. Test data from three different-sized blockage bodies and four wall ventilation settings were analyzed at various Mach numbers and unit Reynolds numbers. The results indicate that with the proper selection of the boundary condition parameters, the wall correction method can predict blockage corrections consistent with the wall measurements for Mach numbers as high as 0.95.

Iyer, Venkit↗
NASA NTRS2003

Improvements to Wall Corrections at the NASA Langley 14 x 22-Ft Subsonic Tunnel

The new wall pressure measurement system and the TWICS wall correction system for the 14x22-Ft subsonic tunnel are described. Results from a recent semispan test and a full-span test are presented. Comparison with existing classical methods of correction is shown. A modification of the TWICS code to treat the effect due to a deflected wake from a high-lift wing is also discussed. The current implementation of TWICS for the 14x22-Ft tunnel is shown to be an improvement over existing methods.

Iyer, Venkit↗
NASA NTRS2001

Sensitivity Study of the Wall Interference Correction System (WICS) for Rectangular Tunnels

An off-line version of the Wall Interference Correction System (WICS) has been implemented for the NASA Langley National Transonic Facility. The correction capability is currently restricted to corrections for solid wall interference in the model pitch plane for Mach numbers less than 0.45 due to a limitation in tunnel calibration data. A study to assess output sensitivity to measurement uncertainty was conducted to determine standard operational procedures and guidelines to ensure data quality during the testing process. Changes to the current facility setup and design recommendations for installing the WICS code into a new facility are reported.

Walker, Eric L.↗
NASA NTRS2001

Parameter Sensitivity Study of the Wall Interference Correction System (WICS)

An off-line version of the Wall Interference Correction System (WICS) has been implemented for the "NASA Langley National Transonic Facility. The correction capability is currently restricted to corrections for solid wall interference in the model pitch plane for Mach numbers, less than 0.45 due to a limitation in tunnel calibration data. A study to assess output sensitivity to the aerodynamic parameters of Reynolds number and Mach number was conducted on this code to further ensure quality during the correction process. In addition, this paper includes all investigation into possible correction due to a semispan test technique using a non metric standoff and all improvement to the standard data rejection algorithm.

Walker, Eric L.↗
NASA NTRS2001

Sensitivity Study of the Wall Interference Correction System (WICS) for Rectangular Tunnels

An off-line wall version of the Wall Interference Correction System (WICS) has been implemented for the NASA Langley National Transonic Facility. The correction capability is currently restricted to corrections for solid wall interference in the model pitch plane for MAch numbers less than 0.45 due to limitation in tunnel calibration data. A study to assess output sensitivity to measurement uncertainty was conducted to determine standard operational procedures and guidelines to ensure data quality during the testing process.

Walker, Eric L.↗
NASA NTRS2000

Implementation of the WICS Wall Interference Correction System at the National Transonic Facility

The Wall Interference Correction System (WICS) is operational at the National Transonic Facility (NTF) of NASA Langley Research Center (NASA LaRC) for semispan and full span tests in the solid wall (slots covered) configuration, The method is based on the wall pressure signature method for computing corrections to the measured parameters. It is an adaptation of the WICS code operational at the 12 ft pressure wind tunnel (12ft PWT) of NASA Ames Research Center (NASA ARC). This paper discusses the details of implementation of WICS at the NTF including, tunnel calibration, code modifications for tunnel and support geometry, changes made for the NTF wall orifices layout, details of interfacing with the tunnel data processing system, and post-processing of results. Example results of applying WICS to a semispan test and a full span test are presented. Comparison with classical correction results and an analysis of uncertainty in the corrections are also given. As a special application of the code, the Mach number calibration data from a centerline pipe test was computed by WICS. Finally, future work for expanding the applicability of the code including online implementation is discussed.

Iyer, Venkit↗
NASA NTRS2000

Implementation of the WICS Wall Interference Correction System at the National Transonic Facility

The Wall Interference Correction System (WICS) is operational at the National Transonic Facility (NTF) of NASA Langley Research Center (NASA LaRC) for semispan and full span tests in the solid wall (slots covered) configuration. The method is based on the wall pressure signature method for computing corrections to the measured parameters. It is an adaptation of the WICS code operational at the 12 ft pressure wind tunnel (12ft PWT) of NASA Ames Research Center (NASA ARC). This paper discusses the details of implementation of WICS at the NTF including tunnel calibration, code modifications for tunnel and support geometry, changes made for the NTF wall orifices layout, details of interfacing with the tunnel data processing system, and post-processing of results. Example results of applying WICS to a semispan test and a full span test are presented. Comparison with classical correction results and an analysis of uncertainty in the corrections are also given. As a special application of the code, the Mach number calibration data from a centerline pipe test was computed by WICS. Finally, future work for expanding the applicability of the code including online implementation is discussed.

Iyer, Venkit↗
NASA NTRS1995

Computer program BL2D for solving two-dimensional and axisymmetric boundary layers

This report presents the formulation, validation, and user's manual for the computer program BL2D. The program is a fourth-order-accurate solution scheme for solving two-dimensional or axisymmetric boundary layers in speed regimes that range from low subsonic to hypersonic Mach numbers. A basic implementation of the transition zone and turbulence modeling is also included. The code is a result of many improvements made to the program VGBLP, which is described in NASA TM-83207 (February 1982), and can effectively supersede it. The code BL2D is designed to be modular, user-friendly, and portable to any machine with a standard fortran77 compiler. The report contains the new formulation adopted and the details of its implementation. Five validation cases are presented. A detailed user's manual with the input format description and instructions for running the code is included. Adequate information is presented in the report to enable the user to modify or customize the code for specific applications.

Iyer, Venkit↗
NASA NTRS1993

Transition prediction and control in subsonic flow over a hump

The influence of a surface roughness element in the form of a two-dimensional hump on the transition location in a two-dimensional subsonic flow with a free-stream Mach number up to 0.8 is evaluated. Linear stability theory, coupled with the N-factor transition criterion, is used in the evaluation. The mean flow over the hump is calculated by solving the interacting boundary-layer equations; the viscous-inviscid coupling is taken into consideration, and the flow is solved within the separation bubble. The effects of hump height, length, location, and shape; unit Reynolds number; free-stream Mach number, continuous suction level; location of a suction strip; continuous cooling level; and location of a heating strip on the transition location are evaluated. The N-factor criterion predictions agree well with the experimental correlation of Fage; in addition, the N-factor criterion is more general and powerful than experimental correlations. The theoretically predicted effects of the hump's parameters and flow conditions on transition location are consistent and in agreement with both wind-tunnel and flight observations.

Masad, Jamal A.↗
NASA NTRS1993

Three-Dimensional Boundary-Layer program (BL3D) for swept subsonic or supersonic wings with application to laminar flow control

The theory, formulation, and solution of three-dimensional, compressible attached laminar flows, applied to swept wings in subsonic or supersonic flow are discussed. Several new features and modifications to an earlier general procedure described in NASA CR 4269, Jan. 1990 are incorporated. Details of interfacing the boundary-layer computation with solution of the inviscid Euler equations are discussed. A description of the computer program, complete with user's manual and example cases, is also included. Comparison of solutions with Navier-Stokes computations with or without boundary-layer suction is given. Output of solution profiles and derivatives required in boundary-layer stability analysis is provided.

Iyer, Venkit↗
NASA NTRS1992

Inviscid and viscous flow calculations for the F16XL configuration

The viewgraphs and discussion of the ongoing activity at NASA Langley Research Center (LaRC) in support of Supersonic Laminar FLow Control (SLFC) research, presented at the High-Speed Research Workshop, May 14-16, 1991, are provided. Details of the computation involved in obtaining the meanflow around bodies in high-speed flow and interfacing the results to a stablilty analysis is presented. Particular attention is given to the F-16XL configuration, which is the test-bed for the supersonic LFC experiment. Meanflow solutions for two geometries are discussed. The first one is for the F-16XL wing, with emphasis on the flow near the attachment line and the upper surface. Calculations were done with and without suction. The results were processed using an interface program and fed into a stability analysis program. The second geometry is a scale model of a swept wing leading edge at M = 3.5. Experimental measurements on transition on this model are planned at NASA LaRC. The computations are in support of this effort.

Iyer, Venkit↗
NASA NTRS1992

Computational study of transition front on a swept wing leading-edge model

The e(N) method is employed with Navier-Stokes calculations to study 3D supersonic boundary layers at the leading-edge region of swept wings with attention given to the conditions for linear stability. Mean-flow profiles are computed as solutions to the Navier-Stokes equations, and the e(N) method is used to identify the onset of the transition. Specific treatment is given to the identification of parameters which affect the transition such as free-stream Reynolds number, wall cooling, and boundary-layer suction levels. The boundary layer can be stabilized to below N=10 levels in all locations by utilizing distributed suction, and enhanced stabilization can also be achieved by employing wall cooling and reduced free-stream Reynolds numbers. This study presents key calculations for corresponding experimental investigations by shedding light on requirements for test conditions and measurement requirements.

Iyer, Venkit↗
NASA NTRS1991

Application of linear stability theory in laminar flow design

The linear stability of fully three-dimensional supersonic boundary layers formed over swept-wing configurations is investigated using a modified version of the linear stability code COSAL. Configurations studied include a highly swept leading-edge model to be utilized for transition studies in the LARC Low-disturbance Mach 3.5 Pilot Tunnel. The model is a representation of the leading edge of a laminar flow control wing for the F-16XL aircraft. In addition, the region over a laminar flow control glove fitted on the midportion of an F-16XL wing was studied. For each configuration, estimates of the location of the onset of transition were computed using linear stability theory and the e exp N method. The effectiveness of suction in stabilizing the boundary layer over the F-16XL wing glove was also investigated.

Iyer, Venkit↗
NASA NTRS1991

Assessment of meanflow solutions for instability analysis of transitioning flows

Meanflow solutions of 3D supersonic flow past a cone at incidence and a swept leading edge wing have been obtained by thre methods, viz., boundary-layer, parabolized Navier-Stokes, and thin shear-layer Navier-Stokes solvers. The smoothness and accuracy of the solution profiles are compared with a view to applying the meanflow solution to boundary-layer stability analysis.

Iyer, Venkit↗
NASA NTRS1991

Testing of transition-region models: Test cases and data

Mean flow quantities in the laminar turbulent transition region and in the fully turbulent region are predicted with different models incorporated into a 3-D boundary layer code. The predicted quantities are compared with experimental data for a large number of different flows and the suitability of the models for each flow is evaluated.

Singer, Bart A.↗