J Inness | Search NASA

NASA NTRSDate not supplied

Electric Sail Design Sensitivities

Electric Sails (E-Sails) are a promising propulsion technology that seek to enable high characteristic propellentless acceleration for spacecraft to reach distant and/or difficult to reach orbits such as rapid transit to heliopause. The E-Sail system exchanges momentum by using positively charged electrostatic tethers to repel solar wind photons to push it through space. This concept was first theorized by Pekka Janhunen in 2004 with further developments occurring including a NASA Innovative Advanced Concepts Phase 1 and Phase 2 hosted out of NASA’s Marshall Space Flight Center (MSFC). These developments led to further maturation of the overall system, and this paper is designed to help identify different design sensitivities of an integrated Electric Sail system. To approach this, a small team at MSFC took an in-house developed three degrees of freedom (3DoF) simulation tool and a trajectory modelling tool to look at different design parameters and to determine a potential ideal E-Sail configuration. An E-Sail system has different design architectures including a barbell design, hub and spoke design, and a potential hybrid solution. The barbell design features two equally massed satellites that spin around a central point in the tether system. The hub and spoke design features a large central spacecraft with small end spacecraft to aid in formation control of the overall E-Sail system. Leveraging elements from both the hub and spoke, and barbell design, a hybrid option exists where one could have a larger central mass and one or two tethers extended to a smaller end mass [2]. In summary, the hub and spoke design is the ideal configuration for E-Sail with tethers spanning kilometers to achieve the designed design characteristic acceleration of at least one mm/s2 with this architecture being the focus of this study. Different key design parameters were varied as part of this study. These parameters include the total number of tethers, the length of the tethers, spin rate, relative spacecraft mass, tether voltage, inertia per tether, and impact of slew rate changes. These results started from an internal MSFC technology demonstration mission design and then the parameters were varied with engineering judgement to ensure that the results were consistent with expected results. These were varied in the MSFC 3DoF tool and compared to baseline results to generate a candidate ideal E-Sail design system. These results were then used to help inform the mission analysis design for the system. The 3DoF trajectory optimization was performed in the Astrodynamics and Space Science Enabling Toolbox (ASSET) and utilized collocation optimization of control vector pointing with the objective function being transfer duration. A representative model of the E-Sail force was derived as a function of the Sun-pointing vector direction. This model was initialized with a zero Sun Incidence Angle (SIA) trajectory for the initial guess generation, then with a portion of the mission optimized SIA time history for fast outbound transfers. After the trajectory is hyperbolic relative to a heliocentric frame, the SIA is maintained at 0 degrees except for any needed trajectory correction maneuvers. This trajectory optimization looked at different characteristic acceleration values to analyze the impact it had on mission performance. As a result of this study, the team can best inform mission designers and technology development efforts to mature the E-Sail system. This study will allow mission designers to have defined rules-of-thumb to design an E-Sail system to meet desired mission needs as well as providing several sample mission profiles. These design drivers will inform maturation efforts on which design requirements to consider for an integrated E-Sail design.

E-Sail↗

NASA NTRSDate not supplied

Design and Applications of Tethered Spacecraft Simulators

Small, tethered spacecraft, or space tugs, are a promising space capability. They can be deployed on tethers and used for a wide variety of in-space activities; a large portion of which fall under in-space servicing, assembly, manufacturing (ISAM) functions. This includes functions such as structural mating and assembly, servicing, proximity operations, capture, docking, mating, and relocation. However, there is a great deal of work to be done to raise the Technology Readiness Level (TRL) of the capabilities needed to fully realize these capabilities. The Flat Floor Robotics Lab (FFRL) at NASA’s Marshall Spaceflight Center (MSFC) has been working on space tug development for several years. The eponymous floor is 44 by 86 feet, made from a self-leveling epoxy. This creates an extremely smooth surface that air bearings can float on with very little friction, creating a simulation of zero gravity in a two-dimensional plane. The lab has several platforms of various sizes that act as vehicle simulators for testing sensors, control algorithms, mechanisms, etc. One of these platforms is a small spacecraft simulator, which can be tethered to simulate a space tug. In the last several months, the FFRL team has been working with MSFC’s welding group to conduct a laser beam welding demonstration on air bearing platforms. This demo is utilizing a space tug simulator to fly up to a floating weld platform, where two parts are clamped together and laser welded. The space tug simulator has an air bearing to provide float, as well as several actuated air thrusters to provide propulsion and make the simulator maneuverable. Currently, flights of this simulator are completed by a human operator. An RF hand controller sends signals to both actuate and fire three sets of thrusters on the simulator. This makes any maneuvers of the space tug highly subject to human error, and operators must have dedicated practice time before being able to perform maneuvers with any sufficient reliability. For the current laser welding demonstration, human operated performance is sufficient, but future implementations of in-space welding and other ISAM efforts will require higher precision, reliability, and autonomy. MSFC has funded a project that will allow a small team in the FFRL to develop the next generation of space tug simulator, which will be automated. Closed loop control will allow a user to command a position, or set of positions, that the simulator will be able to “fly” to on its own. This Maneuverable Automated Tethered Spacecraft (MATS) simulator will have configurable design, to allow a variety of payloads and mission configurations to be demonstrated on the air bearing floor. This will be an invaluable test bed for low and mid TRL advancement for space tether mission subsystems, such as more advanced demonstrations of in-space welding. Once one MATSS is constructed and demonstrated effectively, several more can be built, enabling more advanced tether missions; Electric Sail test beds, sensor arrays, and other science-enabling missions. This paper will detail the design and test of the FFRL’s MATS simulator, including efforts to establish closed loop control and autonomous capabilities. It will also detail use cases for this technology, and how it will further develop both develop science and exploration missions.

Space Tethers↗