Search NASA⌕ Search

Engineering topics

Jacobs, G

Publications and source records attributed to Jacobs, G.

Water-gas shift: Characterization and testing of nanoscale YSZ supported Pt catalysts

Nano-scale Y-doped zirconium oxide materials were prepared with high surface areas (150-200 m(2)/g) and small nano-crystallites (<8 nm). A combination of XANES and EXAFS was used to show that ZrO2 exhibited the tetragonal phase, while the Zr0.5Y0.5O1.75 support displayed the cubic phase. A comparison with undoped zirconia suggests that the Zr0.9Y0.1O1.95 support was tetragonal in structure. A slight increase in d-spacing observed in HR-TEM for the Zr0.9Y0.1O1.95 support relative to undoped ZrO2, along with a shift to lower 2 theta in XRD, provide evidence that Y-doping caused macrostrain. STEM imaging confirmed that the Pt clusters ranged from 0.5 to 2 nm over all three supports. Catalyst reducibility was explored by H-2-TPR, XANES at the Zr K-edge, and TPR-XANES at the Pt L-III edge. A higher concentration of surface defects for the 0.5%Pt/Zr0.9Y0.1O1.95 catalyst relative to 0.5%Pt/ZrO2 was confirmed by DRIFTS of adsorbed CO, while a greater surface mobility of surface formate was suggested based on forward formate decomposition experiments in steam. The Y-doped Pt promoted catalysts displayed higher water-gas-shift activity relative to the 0.5%Pt/ZrO2 catalyst when the Y content was at or below 50%, with the best catalyst being 0.5%Pt/Zr0.9Y0.1O1.95. (C) 2015 Elsevier B.V. All rights reserved.

Pt/YSZ↗

Fischer-Tropsch Synthesis: Influence of CO Conversion on Selectivities H2/CO Usage Ratios and Catalyst Stability for a 0.27 percent Ru 25 percent Co/Al2O3 using a Slurry Phase Reactor

The effect of CO conversion on hydrocarbon selectivities (i.e., CH{sub 4}, C{sub 5+}, olefin and paraffin), H{sub 2}/CO usage ratios, CO{sub 2} selectivity, and catalyst stability over a wide range of CO conversion (12-94%) on 0.27%Ru-25%Co/Al{sub 2}O{sub 3} catalyst was studied under the conditions of 220 C, 1.5 MPa, H{sub 2}/CO feed ratio of 2.1 and gas space velocities of 0.3-15 NL/g-cat/h in a 1-L continuously stirred tank reactor (CSTR). Catalyst samples were withdrawn from the CSTR at different CO conversion levels, and Co phases (Co, CoO) in the slurry samples were characterized by XANES, and in the case of the fresh catalysts, EXAFS as well. Ru was responsible for increasing the extent of Co reduction, thus boosting the active site density. At 1%Ru loading, EXAFS indicates that coordination of Ru at the atomic level was virtually solely with Co. It was found that the selectivities to CH{sub 4}, C{sub 5+}, and CO{sub 2} on the Co catalyst are functions of CO conversion. At high CO conversions, i.e. above 80%, CH{sub 4} selectivity experienced a change in the trend, and began to increase, and CO{sub 2} selectivity experienced a rapid increase. H{sub 2}/CO usage ratio and olefin content were found to decrease with increasing CO conversion in the range of 12-94%. The observed results are consistent with water reoxidation of Co during FTS at high conversion. XANES spectroscopy of used catalyst samples displayed spectra consistent with the presence of more CoO at higher CO conversion levels.

01 COAL, LIGNITE, AND PEAT↗

Fischer-Tropsch Synthesis: Characterization and Reaction Testing of Cobalt Carbide

Hydrogenation of carbon monoxide was investigated for cobalt carbide synthesized from Co{sub 3}O{sub 4} by CO carburization in a fixed-bed reactor. The cobalt carbide synthesized was characterized by BET surface area, X-ray diffraction, scanning electron microscopy, X-ray absorption near edge spectroscopy, and extended X-ray absorption fine structure spectroscopy. The catalysts were tested in the slurry phase using a continuously stirred tank reactor at P = 2.0 MPa, H{sub 2}/CO = 2:1 in the temperature range of 493-523 K, and with space velocities varying from 1 to 3 Nl h{sup -1} g{sub cat}{sup -1}. The results strongly suggest that a fraction of cobalt converts to a form with greater metallic character under the conditions employed. This was more pronounced on a Fischer-Tropsch synthesis run conducted at a higher temperature (523 versus 493 K).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fischer Tropsch synthesis : influence of Mn on the carburization rates and activities of Fe-based catalysts by TPR-EXAFS/XANES and catalyst testing.

Fe-based catalysts containing different amounts of Mn were tested for Fischer-Tropsch synthesis using a stirred tank reactor at 270 C, 1.21 MPa, and H{sub 2}:CO = 0.7. Catalyst activation by carburization with 10% CO/He was followed by Temperature Programmed Reduction/X-ray Absorption Spectroscopy (TPR-EXAFS/XANES) from room temperature to 300 C. {gamma}-Fe{sub 2}O{sub 3} was converted into iron carbides, whereas MnO{sub x} was reduced to oxygen deficient MnO. Mn hindered Fe carburization, such that the carburized catalyst displayed higher Fe{sub 3}O{sub 4} content than the catalyst without Mn. EXAFS fitting indicates that the carburized catalyst contained a mixture of Hgg carbide, Fe{sub 3}O{sub 4}, and Mn oxides. Increasing Mn content led to higher CH{sub 4} and light product selectivities, and lower light olefin selectivities. Higher and stable conversions were obtained with a catalyst containing an almost equimolar Fe/Mn ratio relative to the catalyst without Mn. Selectivity trends are attributed to the higher WGS rates observed on the FeMn catalysts, consistent with the structural differences observed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Studies on KIT-6 Supported Cobalt Catalyst for Fischer–Tropsch Synthesis

KIT-6 molecular sieve was used as a support to prepare cobalt catalyst for Fischer-Tropsch synthesis (FTS) using an incipient wetness impregnation method to produce cobalt loadings of 15 and 25 wt%. The catalysts were characterized by BET surface area, X-ray diffraction, scanning transmission election microscopy (STEM), extended X-ray absorption fine spectroscopy and X-ray absorption near edge spectroscopy. The catalytic properties for FTS were evaluated using a 1L CSTR reactor. XRD, pore size distribution, and STEM analysis indicate that the KIT-6 mesostructure remains stable during and after cobalt impregnation and tends to form smaller cobalt particles, probably located inside the mesopores. The mesoporous KIT-6 exhibited a slightly higher cobalt dispersion compared to amorphous SiO{sub 2} supported catalyst. With the higher Co loading (25 wt%) on KIT-6, partial structural collapse was observed after the FTS reaction. Compared to an amorphous SiO{sub 2} supported cobalt catalyst, KIT-6 supported cobalt catalyst displayed higher methane selectivity at a similar Co loading, likely due to diffusion effects.

01 COAL, LIGNITE, AND PEAT↗

Low Temperature Water–gas Shift: Differences in Oxidation States Observed with Partially Reduced Pt/MnOX and Pt/CeOX Catalysts Yield Differences in OH Group Reactivity

The Pt-ceria synergy may be described as the dehydrogenation of formate formed on the surface of the partially reducible oxide (PRO), ceria, by Pt across the interface, with H{sub 2}O participating in the transition state. However, due to the rising costs of rare earth oxides like ceria, replacement by a less expensive partially reducible oxide, like manganese oxide, is desirable. In this contribution, a comparison between Pt/ceria and Pt/manganese oxide catalysts possessing comparable Pt dispersions reveals that there are significant differences and certain similarities in the nature of the two Pt/PRO catalysts. With ceria, partial reduction involves reduction of the oxide surface shell, with Ce{sup 3+} at the surface and Ce{sup 4+} in the bulk. In the case of manganese oxide, partial reduction results in a mixture of Mn{sup 3+} and Mn{sup 2+}, with Mn{sup 2+} located at the surface. With Pt/CeO{sub X}, a high density of defect-associated bridging OH groups react with CO to yield a high density of the formate intermediate. With Pt/MnO{sub X}, the fraction of reactive OH groups is low and much lower formate band intensities result upon CO adsorption; moreover, there is a greater fraction of OH groups that are essentially unreactive. Thus, much lower CO conversion rates are observed with Pt/MnO{sub X} during low temperature water-gas shift. As with ceria, increasing the Pt loading facilitates partial reduction of MnO{sub X} to lower temperature, indicating metal-oxide interactions should be taken into account.

58 GEOSCIENCES↗

Fischer Tropsch synthesis : an in-situ TPR-EXAFS/XANES investigation of the influence of Group I alkali promoters on the local atomic and electronic structure of carburized iron/silica catalysts.

The promoting impact of alkali metals (i.e., Li, Na, K, Rb, Cs) on the carburization rate of Fe in Fe/Si catalysts was investigated by X-ray absorption spectroscopy. A multisample holder was used, allowing nearly simultaneous examination of the catalysts during activation in a CO/He mixture. With the white line intensity and shape as a fingerprint for oxidation state, TPR/XANES analysis enabled us to measure the relative composition of the different compounds as a function of the carburization time, temperature, and atomic number of the group 1 promoter. At the same time, TPR/EXAFS provided information on the changes in local atomic structure that accompanied the oxidation state changes. The rate of carburization increased in the following order: unpromoted < Li < Na < K = Rb = Cs. After 10 h of treatment the samples containing K, Rb, and Cs were completely carburized, and residual quantities of iron oxides were detected in both unpromoted and Li-promoted samples. The EXAFS spectra after carburization could be fitted well by considering a model containing Hagg carbide and Fe{sub 3}O{sub 4}. After 10 h of CO/He treatment at 290 C, the main component observed was Hagg carbide. A model containing Hagg and {var_epsilon}-carbides, and Fe{sub 3}O{sub 4}, was also investigated. However, the r-factor was not significantly impacted by including {var_epsilon}-carbide in the fitting, and the resulting contribution of {var_epsilon}-carbide in each catalyst from the model was virtually negligible. Selectivity differences are thus not likely due to changes in the carbide distribution. Rather, the alkali promoter increases the CO dissociative adsorption rate, resulting in an increase in the surface coverage of dissociated CO and an inhibition in the olefin readsorption rate. This in turn results in higher olefin selectivities, in agreement with previous catalytic tests.

01 COAL, LIGNITE, AND PEAT↗