Search NASA⌕ Search

Engineering topics

Jakubowski, A. K.

Publications and source records attributed to Jakubowski, A. K..

13 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Rectangular jets in a crossflow

Rectangular jets injected from a flat plate into a crossflow at large angles have been studied. Results were obtained as surface pressure distributions, mean velocity vector plots, turbulence intensities, and Reynolds stresses in the jet plume. The length-to-width ratio of the jets was 4, and the jets were aligned streamwise as single and side-by-side dual jets. The jet injection angles were 90 and 60 deg. Surface pressure distribution results were obtained for jet-to-freestream velocity ratios of 2.2, 4, and 8. Mean flow and turbulence flowfield data were obtained for the side-by-side dual jets, mainly for the jet-to-freestream velocity ratio of 4. The jets featured strong negative pressure peaks near the front nozzle corners. The 60-deg jets produced lower magnitude negative pressures, which are distributed over a lesser area when compared to the 90-deg jets.

Kavsaoglu, M. S.↗
NASA NTRS1986

Dual rectangular jets from a flat plate in a crossflow

Wind tunnel tests were carried out in order to study the single and dual rectangular crossflow jets injected from a flat plate perpendicular to a free stream. The length-to-width ratio of the jets was 3.97, and the spacing between the center lines was 4.7 times the width of a single jet. Surface pressure distributions were obtained for jet-to-freestream velocity ratios of 2.2 and 4, respectively. The following conclusions are offered on the basis of the experimental results: (1) the downstream extension of the negative pressures is extended to the dual jets in comparison to the single jet; (2) by increasing the jet-to-freestream velocity ratio the downstream extension of negative pressures is reduced, but negative upstream pressures become larger; (3) very high peak negative pressures occur at the front side edges of the rectangular jets compared to round jets. Velocity vector plots in the flowfield of the dual jets are given.

Kavsaoglu, M.↗
NASA NTRS1983

Surface pressures induced on a flat plate with in-line and side-by-side dual jet configurations

A jet in a crossflow is of interest in numerous practical situations including jet-powered VTOL aircraft. Two aspects of the problem have received little prior study. First is the effect of the angle of the jet to the crossflow. Second is the performance of dual-jet configurations both in-line and side-by-side. The test plan for this work was designed to address these two aspects. The experiments were conducted in the 7 x 10 tunnel at NASA Ames at velocities from 14.5 - 35.8 m/sec (47.6 - 117.4 ft/sec.). Detailed pressure distributions are presented for single and dual jets over a range of velocity ratios from 3 to 8, spacings from 2 to 6 diameters and injection angles of 90, 75, and 105 degrees. The effects of the various parameters and the differences between the axisymmetric and flat plate geometries on the nature, size, shape, and strength of the interaction regions on the body surfaces are shown.

Schetz, J. A.↗
NASA NTRS1983

Jet trajectories and surface pressures induced on a body of revolution with various dual jet configurations

A jet in a cross flow is of interest in practical situations including jet-powered VTOL aircraft. Three aspects of the problem have received little prior study. First is the effect of the angle of the jet to the crossflow. Second is the performance of dual-jet configurations. The third item for further study is a jet injected from a body of revolution as opposed to a flat plate. The Test Plan for this work was designed to address these three aspects. The experiments were conducted in the 7 x 10 tunnel at NASA Ames at velocities 14.5 - 35.8 m/sec (47.6 - 117.4 ft/sec). Detailed pressure distributions are presented for single and dual jets over a range of velocity ratios from 3 to 8, spacings from 2 to 6 diameters and injection angles of 90, 75 and 60 degrees. Some flowfield measurements are also presented, and it is shown that a simple analysis is capable of predicting the trajectories of the jets.

Schetz, J. A.↗
NASA NTRS1982

Experimental study of surface pressures induced on a flat plate and a body of revolution by various dual jet configurations

The effect of the angle of a jet to a crossflow, the performance of dual jet configurations, and a jet injected from a body of revolution as opposed to a flat plate were investigated during experiments conducted in the 7x10 tunnel at NASA Ames at Velocities from 14.5 m/sec to 35.8 m/sec (47.6 to 117.4 ft/sec.). Pressure distributions are presented for single and dual jets over a range of velocity ratios from 2 to 10, spacings from 2 to 6 diameters and injection angles of 90, 75, 60, and 105 degrees. For the body of revolution tests, the ratio of the jet to body diameters was set as large (1/2) in order to be more representative of V/STOL aircraft applications. Flat plate tests involved dual jets both aligned and in side by side configurations. The effects of the various parameters and the differences between the axisymmetric and planar body geometrics on the nature, size, shape, and strength of the interaction regions on the body surfaces are shown. Some flowfield measurements are also presented, and it is shown that a simple analysis is capable of predicting the trajectories of the jets.

Schetz, J. A.↗
NASA NTRS1981

Flow separation in inlets at incidence angles

Wind-tunnel pressure data and flow pictures obtained for two two-dimensional inlet models have been examined to study the internal flow structure and separation at large incidence angles. The inlet models were 12-in. high (diffuser exit height) and had internal contraction ratio of 1.21 and 1.17. They were tested at low forward speeds over a wide range of throat Mach numbers (inlet mass flow rates) and angles of incidence. Characteristic features of the internal flow such as a drastic change of pressure gradient near the highlight, local separation bubbles and shock/boundary-layer interactions have been indicated and discussed. For a few specific cases, the experimental surface pressure distributions have been compared with theoretical predictions.

Jakubowski, A. K.↗
NASA NTRS1975

Internal cowl-separation at high incidence angles

Internal flow separation at large incidence angles is studied on the basis of wind-tunnel pressure data for six axisymmetric inlet geometries. The inlet geometric variables investigated are the angle of incidence, the throat Mach number, the internal lip contraction ratio, 'sharpness' of the external shape, and freestream velocity. It is shown that an increase in lip contraction ratio delays internal flow separation, while an increase in the sharpness of the external profile tends to reduce the angle of incidence at which complete flow separation occurs. It is also shown that inlet flow separation is subject to scale effects associated with the boundary layer on the cowl surface. The scale effects are particularly pronounced at very high throat Mach numbers.

Jakubowski, A. K.↗
NASA NTRS1974

Heat-transfer and pressure distributions for laminar separated flows downstream of rearward-facing steps with and without mass suction

Heat-transfer and pressure distributions were measured for laminar separated flows downstream of rearward-facing steps with and without mass suction. The flow conditions were such that the boundary-layer thickness was comparable to or larger than the step height. For both suction and no-suction cases, an increase in the step height resulted in a sharp decrease in the initial heat-transfer rates behind the step. Downstream, however, the heat transfer gradually recovered back to less than or near attached-flow values. Mass suction from the step base area increased the local heat-transfer rates; however, this effect was relatively weak for the laminar flows considered. Even removal of the entire approaching boundary layer raised the post-step heat-transfer rates only about 10 percent above the flatplate values. Post-step pressure distributions were found to depend on the entrainment conditions at separation. In the case of the solid-faced step, a sharp pressure drop behind the step was followed by a very short plateau and relatively fast recompression. For the slotted-step connected to a large plenum but without suction, the pressure drop at the base was much smaller and the downstream recompression more gradual than that for solid-faced step.

Brown, R. D.↗
NASA NTRS1974

Rearward-facing steps in laminar supersonic flows with and without suction

An experimental investigation of heat-transfer and pressure distributions within regions of laminar separated flows produced by two-dimensional rearward-facing steps has been carried out at freestream Mach numbers of around 4 in the range of step height-to-boundary layer thickness varying from 0.1 to 2.4. With no suction from the separated area, the ratio of the maximum post-step heat transfer to the attached-flow values was less than unity. The maximum heating-rate region was located far downstream of the reattachment plate stagnation point. Mass suction from the separated area increased the local heating rates, this effect was however relatively weak for purely laminar flow conditions and the competing effect of the step height clearly predominated. At step heights comparable with boundary-layer thickness, even removing the entire approaching boundary layer was not sufficient to raise the post-step heating rates above the flat-plate values.

Jakubowski, A. K.↗
NASA NTRS1973

Experimental study of supersonic laminar base flow with and without suction

Heat-transfer and pressure distributions in laminar separated flows downstream of rearward-facing steps with and without mass suction were investigated at Mach numbers around 4 for the conditions when the boundary-layer thickness was comparable to or larger than the step height. In both suction and no-suction cases, an increase of the step height resulted in a sharp drop of the base heating rates, which then gradually recovered to less than or near attached-flow values obtained with flat-plate configuration. Mass suction from the step base area increased the local heating rates; this effect, however, was relatively weak for laminar flows tested, and the competing effect of the step height clearly predominated. It was found that even removal of the entire incoming boundary layer was not sufficient to raise the poststep heating rates above the flat-plate values. The base pressure in the no-suction, solid-step case correlated reasonably well with the step height-to-boundary-layer thickness ratio and with the Reynolds number based on the step height.

Jakubowski, A. K.↗
NASA NTRS1973

Rearward-facing steps in laminar supersonic flows with and without suction.

It was found in the experimental study conducted that, for both suction and no-suction cases, an increase in the step height caused a sharp drop in the initial heating rates which then gradually recovered to less or near the attached-flow values. The height of the step controlled the heating rates at the step base. Mass suction from the separated area increased the local heating rates, the relative increase being most significant immediately behind the step. In general, however, the effect of mass suction on heat-transfer at all laminar flows was relatively weak.

Jakubowski, A. K.↗