Search NASA⌕ Search

Engineering topics

Jan-renee Carlson

Publications and source records attributed to Jan-renee Carlson.

7 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Identification of Best Practices for Predicting Inlet Performance Using FUN3D Part 2: Installed Inlets.

A series of studies were performed to assess the impacts of boundary condition type and placement, grid refinement, and modeling parameters such as turbulence model and flux limiter on the predicted inlet performance for installed inlet configurations using the FUN3D flow solver. Two configurations were considered for the study; a wall-mounted Boundary Layer Ingestion (BLI) inlet and the C607 propulsion model tested in the 8x6 Supersonic Wind Tunnel at the NASA Glenn Research Center. The results of the studies were to be used to recommend best practices, as well as to assess the accuracy of FUN3D for inlet predictions. The results of BLI inlet stud-ies showed a minimal impact of grid refinement on the predicted inlet performance for a constant mass flow rate through the inlet. For the C607 propulsion model, the results showed that while the FUN3D predictions at the Aerodynamic Inter-face Plane (AIP) qualitatively agree with the experimental data, FUN3D showed a tendency to overpredict the circumferential distortion metric (IDCmax) and un-derpredict both the radial distortion metric (IDRmax) and the pressure recovery at the AIP (PRAIP ), with the differences between FUN3D and the experimental data increasing with increasing grid refinement and Mach number. Additionally, the outflow boundary location studies performed for both geometries showed that the solution at the AIP was not significantly impacted by the outflow boundary location as long as it was not placed at the location of the AIP. The modeling parameter studies did not indicate a path forward for improved predictions for either inlet con-figuration. Finally, comparisons between the mass flow plug and outflow geometry versions of the C607 propulsion model illustrated favorable agreement, which indi-cates that the differences observed are not caused by the outflow boundary model for this problem. This problem poses significant challenges to Reynolds-averaged Navier-Stokes (RANS) solvers due to the presence of shocks and flow separation in the inlet.

FUN3D↗
NASA NTRSDate not supplied

Mars Sample Return, Sample Retrieval Lander, Reaction Control System Jet Interaction Supersonic Wind Tunnel Test Overview with CFD Predictions

NASA's Mars Sample Return campaign will be launching several missions over the next decade that will work together to return rock samples from Mars back to Earth. The Sample Retrieval Lander (SRL) will deliver the Mars Ascent Vehicle and fetch rover to the surface of Mars in 2006. Rock samples collected by the Mars 2020 Perseverance rover, landing in early 2021, will be loaded on the the ascent vehicle to be launched into Mars orbit for retrieval by yet another spacecraft. The Sample Retrieval Lander will be a blunt entry capsule similar to past Mars entry vehicles like Mars Science Laboratory and Viking. The vehicle will fly a guided entry, using a small lift vector produced by a non-zero trim angle of attack to eliminate downrange and crossrange position errors at the point of parachute deploy. This energy and heading management is achieved with a reaction control system (RCS) that directs the bank angle of the vehicle and also minimizes unwanted capsule dynamics. The reaction control system and control design is based on the Mars Science Laboratory and Mars 2020 RCS systems. However, due to packaging constraints, the backshell of this new entry vehicle has a different geometry than those earlier designs. To certify the RCS system for flight the project must characterize the jet plume interactions with the capsule backshell that could impair or significantly augment the RCS control authority. This characterization will be done through a combination of computational fluid dynamics (CFD) analysis and wind tunnel test. Two candidate arrangements of the RCS jets have been identified for the SRL vehicle and are currently under evaluation before final selection. The aero/RCS plume interactions of these candidate configurations have been measured in a supersonic wind tunnel test in NASA Langley's Unitary Plan Wind Tunnel. The test was conducted in the fall of 2020 and data is currently being reduced. An overview of the candidate RCS configurations are presented here with an overview of the wind tunnel model design, jet scaling and scaled nozzle design, and the test matrix. Preliminary CFD runs are presented with an assessment of the predicted plumes and their interaction with the wake flow of the vehicle. The predicted effects of the model sting is provided as well. This high fidelity wind tunnel test is being conducted much earlier in the SRL project than would normally be done. The test was funded as part of a CFD evaluation task funded by NASA's Aerosciences Evaluation and Test Capabilities Project. The objective of the evaluation task was to compare the ability of CFD to predict complex flows with data that can be measured in the Langley Unitary Plan Wind Tunnel. RCS Jet interactions were selected as a type of complex flow that is important to NASA missions. In addition to providing useful data to the SRL project, there was added emphasis on quantifying the accuracy of the CFD predictions and wind tunnel test data. An overview of the uncertainty quantification methodologies for computational and experimental portions of this test is presented.

blunt body↗
NASA NTRSDate not supplied

Computational Investigation of Retropropulsion Operating Environments with a GPU-Enabled Detached Eddy Simulation Approach

Human exploration of the surface of Mars will require an extended powered descent phase of flight, during which aerodynamic-propulsive interference effects can be significant. Characterization of these environments to enable implementation of this technology into a flight vehicle will rely heavily on computational simulation. This work advances the understanding of retropropulsion aerodynamics through application of a massively parallel detached eddy simulation approach on a GPU-accelerated computational framework, yielding data that are largely unachievable with conventional high-performance computing resources. This work includes time-dependent and time-averaged forces and moments on a conceptual, full-scale vehicle in environments and operating conditions relevant to human Mars exploration. Conditions are examined where the engine exhaust flow transitions between over-expanded and under-expanded flow structures, and flight operation will require the ability to maintain control of the vehicle during such a transition. These transitions occur as the vehicle decelerates, and as such, this investigation includes supersonic, transonic, and subsonic flight conditions. Options for vehicle control during powered flight include differential throttling of the engines. This paper provides an overview of the computational campaign, approach, and discussion of results in characterizing the resulting aerodynamics for differential throttling with retropropulsion in atmospheric environments.

EDL↗
NASA NTRSDate not supplied

Wall-Modeled Large-Eddy Simulations for High-Lift Configurations using FUN3D

Wall-modeled large-eddy simulation (WMLES) capability has recently been implemented into FUN3D, an unstructured, node-centered, finite-volume solver developed at the NASA Langley Research Center. In this paper, WMLES is assessed for two configurations that are representative for high-lift applications. The first configuration is a nominal two-dimensional multielement airfoil that has been extensively studied in the literature. WMLES solutions are computed for four angles of attack and compared with previously reported solutions. Good agreement of integrated forces, surface pressures, and boundary-layer velocity profiles is shown with available experimental data especially at lower angles of attack. WMLES solutions are also computed for the NASA High-Lift Common Research Model over a large range of angles of attack. Forces, pitching moments, and pressure distributions are favorably compared with the experimental data up to the maximum lift, including the angle of attack where the maximum lift is obtained experimentally. Eddy visualization techniques of q-criterion and density-gradient magnitude illustrate the resolved content.

High-Lift flows↗