Search NASA⌕ Search

Engineering topics

Jana, Saumyadeep

Publications and source records attributed to Jana, Saumyadeep.

At least 19 records

Embedded Aluminum Nitride Sensors for Advanced Reactors

This project aims to manipulate the of growth of aluminum nitride (AlN) inclusions in an iron-chromium-aluminum (FeCrAl) alloy, using the principle of powder metallurgy and heat treatment methods. to promote the formation of AlN phase within FeCrAl for embedded sensing. This effort seeks to fill in a gap with respect to robust sensor hardware for ubiquitous structural health monitoring of advanced nuclear reactors. A systematic evaluation of various solid-state methods will be performed to understand the influence of process conditions on AlN growth and to promote the growth of desirable AlN phase. Fabricated specimens will be analyzed to investigate the AlN structures that are formed using a suite of tools to characterize the concentration, morphology, and distribution of AlN within the FeCrAl substrate.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

A comparative analysis of residual stresses from friction stir processing of aluminum cast 380 and wrought 7075 alloy sheets: experimental characterization and modeling

Residual stresses are often overlooked in friction stir processing (FSP), but their significant impact on fatigue performance necessitates their consideration in optimizing processing parameters. The first step in this effort is understanding how process conditions influence residual stress distributions, especially across different alloys. This study focuses on determining and explaining the through-thickness residual stress variations and the effect of process temperature on the residual stress magnitude in wrought AA7075 and cast AA380.0 alloys. Additionally, for AA380.0, the impact of a second FSP pass was investigated. To achieve this, hole-drilling electronic speckle pattern interferometry (ESPI) and the thermal pseudo-mechanical (TPM) model within finite element analysis were employed to study the 3D distributions of in-plane residual stresses in processed samples under various conditions. A key finding was the varying impact of process temperatures on residual stress magnitudes. Higher process temperatures reduced stresses in AA380.0 but increased them in AA7075. Additionally, the through-thickness stress distributions differed between the two alloys. Further analysis revealed that yield stresses are crucial in explaining these phenomena and the effects of additional FSP passes. Further, this fundamental understanding will be vital in guiding the efforts to mitigate residual stresses and assess their impact on the performance of FSP aluminum alloys.

36 MATERIALS SCIENCE↗

Friction stir processing: A thermomechanical processing tool for high pressure die cast Al-alloys for vehicle light-weighting

This study uses friction stir processing (FSP) for thermomechanical processing of high-pressure die-casting (HPDC) to modify microstructure and improve mechanical properties. FSP is carried out on two different HPDC aluminum alloys: (a) general-purpose, high-iron, HPDC A380 alloy and (b) premium quality, low-iron HPDC Aural-5 alloy in thin wall, flat plate geometry. Subsequent mechanical testing shows ~30 % and ~65 % enhancement in yield strength and tensile ductility. In addition, FSP leads to ~10 times improvement in fatigue life for A380 alloy and ~70 % improvement in fracture toughness for Aural-5 alloy. These findings emphasize the capability of FSP to modify the microstructure of HPDC Al-alloys-based structural components so that they can demonstrate a good combination of strength, ductility, fracture toughness, and high fatigue properties for long-term durability and reliability.

36 MATERIALS SCIENCE↗

Friction stir processing on a strontium modified, thin-wall, vacuum-assisted high-pressure die-cast Aural-5 alloy to improve tensile and fatigue performance

Here, this study explores the application of friction stir processing (FSP) to enhance the material properties of Sr-modified Aural-5 alloy, with a focus on improved tensile and fatigue properties. Aural-5 is a well-known vacuum-assisted high-pressure die-cast (HPDC) Al-Si7-Mg alloy used in the automotive industry to reduce vehicle weight, enhance fuel efficiency, and lower carbon emissions. This alloy modifies its material chemistry with Sr for fine fibrous networks of eutectic silicon and manganese (Mn) to reduce die soldering. It has significantly less iron (Fe) content resulting in the elimination of detrimental needle-shaped Fe-bearing ß-phase intermetallic and improving ductility. The initial microstructure of as-received HPDC Aural-5 exhibits shrinkage porosity in the middle section, a dendritic microstructure with fibrous Al-Si eutectic colonies, a shear-band structure beneath the die-wall, large dendritic externally solidified crystals (ESCs), needle-shaped Mg 2 Si phase and significant second-phase particulates. Some of those microstructural features, such as porosity, ESCs, needle-shaped Mg 2 Si phase, and large second-phase particles, serve as initiation sites for cracks under mechanical loading, resulting in adverse effects on tensile properties, particularly ductility. FSP effectively transforms the microstructure into a wrought configuration with uniform particle distribution by eliminating porosity and disintegrating dendrites, eutectic colonies, ESCs, second-phase particles, and shear-band structures. FSP-driven microstructure modification enhances yield strength and tensile ductility by ~30% and ~35%, respectively. The fatigue life of the material in a bending mode configuration (stress ratio R = 0.1) after FSP exhibits enhancements ranging from 2.0 to 3.9 times that of the original HPDC Aural-5 alloy, depending on the applied stress level.

36 MATERIALS SCIENCE↗

Enhanced toughness and tear resistance of thin-walled High-Pressure Die-Cast aluminum alloys through Friction stir processing

In this study, we investigate the toughness and resistance to tear of thin-wall high-pressure die-cast (HPDC) aluminum alloys in two different orientations following the implementation of friction stir processing (FSP). The FSP technique was applied to two different HPDC Al-Si alloys: the recyclable-grade, high iron, A380 alloy and the premium-quality, low iron, Aural-5 alloy. Our findings reveal significant tear resistance and strength enhancements for both alloys after FSP modification. Specifically, FSPed A380 alloy requires 126% higher energy to tear, and it has 49% higher tear strength than the HPDC counterpart. Similarly, the tear energy and tear strength of the Aural-5 alloy witness enhancements of 69% and 21%, respectively. In conclusion, these results highlight the potential of FSP as a viable method for augmenting the mechanical properties of HPDC aluminum alloys, thereby opening up new avenues for their utilization in diverse engineering applications for crack obstruction.

36 MATERIALS SCIENCE↗

Preliminary Characterization and Evaluation on FFF Manufactured 316H and ODS Steels

The Advanced Materials and Manufacturing Technology (AMMT) program develops cross-cutting technologies in support of a broad range of nuclear reactor technologies and maintains U.S. leadership in materials and manufacturing technologies for nuclear energy applications. The overarching vision of AMMT is to accelerate the development, qualification, demonstration, and deployment of advanced materials and manufacturing technologies to enable reliable and economical nuclear energy. Solid-state advanced manufacturing techniques can overcome some of the challenges in liquid-based additive manufacturing (AM) processes and should therefore be considered in material design and manufacturing as well. The work presented in this report forms part of a study on solid-state AM techniques of 316 stainless steels (SS) and oxide dispersion strengthened (ODS) steel components and supports the vision and goals of the AMMT program relevant to accelerate the development and deployment of advanced manufacturing processes. Achieving this can provide a safety improvement through larger safety margins, economic benefit for higher efficiency during operation, and a cost reduction through more effective manufacturing processes and less waste. This study provides preliminary information on development of the fused-filament fabrication (FFF) process using different powder types to demonstrate the sensitivity, and therefore the characterization of these sample components. The full solid-state manufacturing feasibility study will be completed and reported in a final feasibility evaluation during 2025. The study investigation used two 14YWT ODS powder batches, which provided information and the effect of different powder morphologies on manufacturability. The two 316SS powders demonstrated the effect of powder size on the manufacturability using FFF. Two product forms, namely a honeycomb structure and flat samples, were manufactured to demonstrate the flexibility of product form.

36 MATERIALS SCIENCE↗

Mitigating Corrosion in Mg Sheet in Conjunction with a Sheet-Joining Method that Satisfies Structural Requirements within Sub-assemblies

This work was undertaken as a LightMAT project funded by the DOE-Vehicles Technology Office. The goal of this work was to develop corrosion protection strategies that simultaneously mitigate corrosion and achieve Class-A surface finish for Mg components in automotive applications. While automotive metals such as steel and aluminum are protected against corrosion through a variety of coating schemes/packages, the efficacy of these existing coating schemes for Mg and Mg- joints is not clear and needs to be determined. Therefore, five commercially available coating schemes and two joining techniques (riveting and Arplas resistance spot welding) were evaluated. The corresponding individual Mg sheet coupons or Mg/Mg joint test coupons were provided by Magna that were then corrosion tested at PNNL using ASTM B117 procedure. The microstructures and mechanical properties of the coupons were analyzed to determine the effectiveness of the joining and corrosion mitigation strategies. Of the coating schemes evaluated, Henkel Bonderite MgC 2.0 pre-treatment + E-coat showed the best corrosion protection and surface finish for individual Mg coupons and Arplas resistance spot welded coupons. However, the strength of Mg/Mg welded joint was reduced after corrosion testing due to some corrosion at the weld nugget. Mg/Mg rivet joints in conjunction with Chemetall oxisilan pre-treatment + polyurethane coating showed good corrosion resistance and some discoloration on the surface finish. Coating schemes comprising pre-treatment with Alodine 5200 + E-coat or Bonderite 1455 + polyurethane coating, in conjunction with Al rivet joints, showed significant corrosion and extensive discoloration of the surface. We anticipate that the results from this work will provide useful guidance to the automotive industry in selecting the appropriate combinations of corrosion protection coatings and joining techniques to fabricate light-weight Mg-based automotive components.

36 MATERIALS SCIENCE↗

Enhanced Tensile and Tear Toughness Properties of Thin-Wall Vacuum-Assisted High-Pressure Die-Cast Aural-5 Alloy by Friction Stir Processing

Steadily rising demand for glider weight reduction has driven the development of vacuum-assisted high-pressure die-cast (HPDC) Al-alloys for automotive structural components. Aural-5 is a strontium-modified HPDC alloy utilizing manganese (Mn) to reduce die soldering, eliminating detrimental needle-shaped Fe-bearing ß-phase intermetallic and improving ductility. HPDC Aural-5 contains shrinkage porosity, dendrites with Al-Si eutectic colonies, externally solidified crystals (ESCs), shear-band structure, and large second-phase particulates. Porosity, ESCs and large second-phase particles work as crack initiation sites, negatively impacting tensile properties. In this study, friction stir processing (FSP) is employed for microstructural modification of a thin-walled HPDC Aural-5 by eliminating porosity and breaking down dendrites, second-phase particles, eutectic colonies, ESCs and shear-band structures to create wrought microstructure with homogenized particle distribution. Mechanical property characterization indicates ~30% and ~35% enhancement in yield strength and ductility and associated marked effects on ~69% improvement in tear toughness according to the ASTM B871 test.

Friction stir processing, Aural-5, Strength, Tear ↗

Friction Stir Processed Repair Welding of Dry Storage Canisters and Mitigation Strategies: Effect of Engineered Barrier Layer on Environmental Degradation

The proposed project aims to develop a friction sir based repair technique to heal cracks of stainless steel dry storage canisters (DSCs), created by the effect of stress corrosion cracking (SCC). In real service conditions, the welded parts of the canisters become prone to SCC under exposure to aggressive chemical environment. The focus of the project is on developing a mitigation strategy that can be implemented for countering SCC in DSCs following a two-pronged approach: (i) apply friction stir processing (FSP) as a crack repair technique while creating compressive residual stresses at the canister material surface, thus improving resistance against SCC; (ii) add molybdenum and/or nitrogen by friction stir based alloying process to create compositions that improve pitting resistance and thus enhance resistance against SCC. The specific project objectives are listed below: • Investigate FSW of 304L SS a potential repair welding technique of dry storage canisters; • Optimize the FSW parameters to introduce surface compressive stress profiles in the weldments; • Develop a FSP method to surface alloy the 304L with nitrogen and Mo by adding CrN and Mo powders; • Evaluate the surface compressive residual stress profile during FSW and FSP processes; • Evaluate the localized corrosion resistance of the FSW and FSP samples as a function of temperature, chloride concentration, and surface alloy composition; • Evaluate the SCC behavior of the FSW and FSP samples as a function of stress, chloride concentration, and temperature at different surface chemistries and induced residual stress profiles.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Shear assisted extrusion process

A shear assisted extrusion process for producing cladded materials wherein a cladding material and a material to be cladded are placed in sequence with the cladded material positioned to contact a rotating scroll face first and the material to be cladded second. The two materials are fed through a shear assisted extrusion device at a preselected feed rate and impacted by a rotating scroll face to generate a cladded extrusion product. This process allows for increased through wall strength and decreases the brittleness in formed structures as compared to the prior art.

Joshi, Vineet V.↗

Effect of tool design and pass strategy on defect elimination and uniform, enhanced tensile properties of friction stir processed high-pressure die-cast A380 alloy

This work reports implementation of friction stir processing (FSP) to locally modify microstructure and create a defect-free processing zone with the aid of different tool designs and altering the passing strategy for two different process parameter combinations. Here, FSP is applied on high pressure die-cast (HPDC) A380 alloy, a widely used Al-Si alloy fabricated in the die casting sector for automotive and aerospace applications. However, the presence of gas and shrinkage porosity, brittle needle-shaped Fe-containing ß-FeSiAl 5 intermetallic compounds, Al-dendrites, coarse and acicular silicon particles, and large second-phase particulates have a detrimental influence on the uniformity of tensile properties across the thickness direction of an HPDC plate. FSP is able to eliminate porosity, refine microstructure and improve tensile properties. An FSP tool design and a passing strategy are identified for the best microstructure consolidation and uniform enhanced tensile properties. This study noted the importance of tool features such as scroll design and flats on tool pin and multiple pass orientation strategy to find best combination of defect-free refined microstructure and uniform tensile strength and ductility across the processing zone of HPDC Al alloys.

36 MATERIALS SCIENCE↗

Room temperature corrosion behaviour of plastically deformed AISI 304 stainless steel by friction stir welding in neutral and acidified chloride solutions

Severe plastic deformation of 304L stainless steel plate was carried out by friction stirring under an isothermal tool temperature at 825°C. The friction stirred zone showed extensive grain refinement, high fraction of low angle grain boundaries due to dislocation rearrangement, Σ3 and Σ9 special grain boundaries and discrete Fe–Cr–Mn-rich particles. Electrochemical polarisation measurements were done on the base metal (BM) and friction stir welded (FSW) specimens in the neutral and acidified 3.5% NaCl solutions. The BM showed marginally better pitting resistance in the neutral chloride solution than the FSW because of a larger fraction of special grain boundaries, and larger grain size. Whereas in acidified 3.5% NaCl solution, the FSW showed better corrosion resistance than the BM. Furthermore, the surface film of the FSW had a lower impedance and a lower defect concentration than the BM indicating higher diffusivity of point defects in the FSW.

36 MATERIALS SCIENCE↗

Delayed onset of discontinuous precipitation-based phase transformation in U10Mo alloys doped with Silicon

A uranium-10 wt% molybdenum (U-10Mo) alloy is one of the primary candidates for metallic fuels that would use low-enriched uranium in place of highly enriched uranium, to support nuclear nonproliferation efforts. Optimal performance of a U-based metallic nuclear fuel can be achieved by retaining the high-temperature, body-centered cubic (bcc) allotrope (γ-U) at room temperature, which can be accomplished in the U-10Mo alloy. However, presence of minor alloying elements can influence the final constitution of room-temperature phases in the U10Mo alloy, specifically, formation of α-U phase which results in anisotropic behavior of the fuel in reactor. Further, through a detailed transmission electron microscopy analysis, the present study reports the constituent phases that are present in a U10Mo alloy containing ~0.1 wt% Si after it is subjected to homogenization heat treatment and thermomechanical processing. For comparison, results from an undoped U10Mo alloy are also included. The experimental results reveal that γ-UMo solid solution is the major phase in a hot-rolled, Si-doped U10Mo alloy metallic fuel foil, along with U 2 MoSi 2 C, UC, and U 2 Mo, after isothermal annealing at 460 °C for 10h. In contrast, after the same heat treatment, the undoped U10Mo alloy metallic fuel had formed a noticeable amount of α-U along prior γ-UMo grain boundaries through discontinuous precipitation (DP, area fraction: ~27.9%) with characteristic lamellar morphology, together with γ-UMo, UC, and U 2 Mo. This result indicates that doping with Si could mitigate the DP reaction in U10Mo alloy and prevent formation of undesirable α-U. This work sheds light on optimizing Si-doping–dominated microstructure in U10Mo fuels and facilitates designing and tuning of microstructures of U10Mo alloys for tailoring the final designed performance of the fuel under irradiation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructure-refinement–driven enhanced tensile properties of high-pressure die-cast A380 alloy through friction stir processing

This work employs friction stir processing (FSP), a well-known severe plastic deformation technique, to selectively modify the microstructure of thin-walled, high-pressure die-cast (HPDC) aluminum alloy A380, a major HPDC alloy fabricated in the die casting sector. FSP effectively breaks down Al dendrites and acicular Si particles, creating a homogenized distribution of equiaxed Si particles in the aluminum matrix. After FSP, the refined Si particles (~1.5 µm) are smaller than the eutectic Si particles (3–8 µm) in HPDC condition. In addition, interparticle distance has decreased almost 50% compared to dendritic arm spacing, and FSP has reduced the aspect ratio of Si particles to ~2. Furthermore, FSP eliminates porosity, and breaks down needle-like second-phase Fe-Mn and Cu-rich particles, yielding a refined, homogeneous distribution. The FSP-induced microstructural refinement and porosity reduction improve bulk yield strength and ductility by 23% and 66%. Tensile properties are enhanced beyond those of the die skin of the HPDC plate, and the alloy possesses lower defect density and a highly refined microstructure. This study establishes the viability of FSP as a tool for microstructure modification and mechanical property improvement for HPDC Al alloys for the light-weighting goal of the automotive industries.

36 MATERIALS SCIENCE↗

Microstructural modification of a high-pressure die-cast A380 alloy through friction stir processing and its effect on mechanical properties

Aluminum alloy A380 is one of the major high-pressure die-cast (HPDC) alloys fabricated in the die casting sector. However, microstructural features such as shrinkage and gas porosity, entrapped oxide inclusions, change in the morphology of eutectic Si particles as a function of casting location, and the presence of multiple second phase particulates, especially Fe-bearing phases in HPDC A380 alloy results in limited ductility, thus, affecting its structural application. However, through proper modification of the as-cast microstructure, it is possible to improve the mechanical performance of alloy A380. In this study, we report the effect of friction stir processing (FSP), a well-known severe plastic deformation (SPD) and thermomechanical processing tool for selective microstructural modification, on A380. FSP effectively refines the as-cast microstructure and breaks down the coarse Si particles, creating a homogenized distribution of equiaxed Si particles in the aluminum matrix. Additionally, FSP eliminates porosity that acts as crack initiation sites, leading to improved mechanical strength and ductility.

Friction stir processing, Aluminum alloys, Mechani↗

Microstructure and mechanical properties of friction stir welded Haynes 282

Advanced ultrasupercritical (A-USC) steam plants are designed to operate at high temperatures and pressures due to the necessity for higher operational efficiency. The extreme operating conditions of A-USC requires the deployment of precipitation strengthened Ni-base alloys that exhibit elevated temperature strength and good fabricability. Fusion welding of precipitation strengthened nickel alloys lead to solidification cracking in fusion zone and/or liquation cracking in heat affected zone. Therefore, an alternative non-melting welding technique is a necessity to efficiently join nickel alloys. In the current study, friction stir welding, a solid state joining technique was implemented on a precipitation strengthened nickel-based superalloy, Haynes 282. Detailed microstructural and mechanical properties characterization was carried out. The processed region exhibited wrought, fine-grained microstructure, absence of weld defects such as voids and cracks and absence of elemental segregation. Both hardness and cross-weld tensile tests demonstrated that the weld region was stronger than the base material. And the cross-weld tensile samples failed in the base material. Based on joint efficiency analysis, friction stir welded Haynes 282 outperformed fusion welds.

36 MATERIALS SCIENCE↗

Evaluation of residual stresses in isothermal friction stir welded 304L stainless steel plates

Friction stir welding was performed on 304L SS plates in order to heal simulated cracks created by electrical discharge machining. Two different tool temperatures (825 and 725 °C) were chosen for this study. Both neutron diffraction and X-ray diffraction techniques were employed to evaluate the residual stresses along two orthogonal reference directions, longitudinal (syy) and transverse (sxx). The former technique was also used to measure residual stresses at various depths. It was found that, at 1 mm depth from the top surface inside the stir zone (SZ), the longitudinal component was tensile in nature while the transverse component was compressive. The nature and magnitude of the residual stress fields, and the position of the peak residual stresses were found to vary with the weld depth. The SZ of the 725 °C weld exhibited higher peak stress than 825 °C weld mainly due to a lack of stress relief at the lower temperature.

Friction stir welding, Steel↗

Microstructural basis for improved corrosion resistance of laser surface processed AZ31 Mg alloy

Despite their excellent strength to weight ratio, wider use of Mg alloys for light weighting applications is limited by their poor corrosion resistance, especially in chloride ion-containing environments. The present study shows improved corrosion resistance imparted by laser surface processing (LSP) of a commercial AZ31 (Mg-3Al-1Zn) alloy. Nanosecond laser processing at three different power settings was carried out on the surface of a 1 mm thick rolled AZ31 sheet. Corrosion testing based on ASTM B117 method and several other electrochemical tests indicates substantial enhancement of corrosion resistance in LSP-treated AZ31. The underlying reason behind improved corrosion resistance of LSP-AZ31 surface has been identified using a variety of characterization tools (SEM, TEM, XPS). Formation of a ~0.5 µm thick mixed metal (Mg, Al) oxide surface film together with refinement in the size and number density of Al-Mn intermetallic particles appear to be playing a major role towards improved corrosion resistance after LSP treatment of AZ31 alloy.

Jana, Saumyadeep↗