Search NASA⌕ Search

Engineering topics

Janke, Christopher J.

Publications and source records attributed to Janke, Christopher J..

8 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Compatibility of Fuel System Elastomers and Plastics with a Fast-Pyrolysis Oil (Bio-oil) at Room Temperature

Herein the compatibility of a fast-pyrolysis bio-oil with 17 elastomer and 21 plastic materials common to fuel storage, dispensing, and delivery systems was assessed by measuring volume and hardness. Diesel was used as the baseline for comparison. The elastomer and plastic specimens were exposed to the test fuels at 23 °C. The exposure times were 4 and 16 weeks for the elastomers and plastics, respectively. The elastomers (except for silicone and styrene butadiene) exhibited pronounced swelling in the bio-oil. This was especially true for the fluorocarbons and acrylonitrile rubbers. For the elastomers, a strong correlation between polarity and volume swell was observed. Compositional and structural analysis on one of the fluorocarbon materials showed that the bio-oil was less effective at extracting phthalate additives than the diesel. However, the crystallinity of a fluorocarbon was altered by the bio-oil. Unlike the elastomers, the plastic materials were less impacted by exposure to the bio-oil. This finding is attributed to their denser and more rigid molecular structures (compared to the elastomers). Notable swelling did occur in the nylons, but this swelling was attributed to water absorption rather than polarity. Comparison with previous studies showed that the observed swelling was lower for both the elastomers and the plastics. Solubility (and hence swell) increases with temperature, and because this study was conducted at 23 °C rather than 50 °C, the reduced temperature is responsible for the lower swell levels.

09 BIOMASS FUELS↗
DOE OSTI2022

Amidoxime-functionalized materials and their use in extracting metal ions from liquid solutions

A method of producing a functionalized material that extracts metal ions from solution, the method comprising: (i) providing a precursor material having nitrile groups appended to its surface; and (ii) reacting said nitrile groups with hydroxylamine or a derivative thereof in the presence of a polar aprotic solvent at a temperature of 60-80° C. for at least 1 hour, to convert at least a portion of said nitrile groups to amidoxime and imide dioxime groups, followed by reaction with a base capable of hydrolyzing any remaining nitrile groups to carboxylic acid groups; wherein said functionalized material has a higher uranium absorption capacity than a functionalized material produced under same conditions except that the nitrile groups are reacted with hydroxylamine in only a protic solvent. The invention is also directed to functionalized materials produced by the above-described method, and methods for using the functionalized material for extracting metal ions from metal-containing solutions.

Janke, Christopher J.↗
DOE OSTI2022

On the Mechanism of the Steady-State Gamma Radiolysis-Induced Scissions of the Phenyl-Vinyl Polyester-Based Resins

The major societal problem of polymeric waste necessitates new approaches to break down especially challenging discarded waste streams. Gamma radiation was utilized in conjunction with varying solvent environments in an attempt to discern the efficacy of radiolysis as a tool for the deliberate degradation of model network polyesters. Our EPR results demonstrated that gamma radiolysis of neat resin and in the presence of four widely used solvents induces glycosidic scissions on the backbone of the polyester chains. EPR results clearly show the formation of alkoxy radicals and C-centered radicals as primary intermediate radiolytic products. Despite the protective role of the phenyl groups on the backbone of the radiation-induced polyester chains, the radiolytic-glycosidic scissions predominate. Among the following three solvents used in this study (water, isopropyl alcohol, and dichloromethane), the highest radiolytic yield of glycosidic scission was achieved using water. The •OH radicals produced in the radiolysis of phenyl unsaturated polyester aqueous suspensions very rapidly abstract H atoms from the methylene group, which is followed by a very rapid glycosidic scission. The lowest glycosidic yield was found in the dichloromethane solutions of these polyester resins due to scavenging by the fast electron capture reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

The compatibility performance of fuel system elastomers with two dioxolane molecules as blends with diesel

The compatibility of 17 elastomers with two dioxolane molecules was assessed by volume change and hardness measurements. Each molecule was blended with diesel in concentrations of 0, 10, 20 and 30 wt.%. The elastomers included two fluorocarbons, six acrylonitrile butadiene rubbers (NBRs), and one each of fluorosilicone, chloroprene rubber (CR), polyurethane, styrene butadiene rubber (SBR), hydrogenated NBR (HNBR), a blend of NBR and PVC (OZO), epichlorohydrin/ ethylene oxide (ECO), ethylene propylene diene monomer (EPDM), and silicone. Specimens of each elastomer were immersed in the test fuels for a period of 4 weeks and measured for property change. Afterwards they were dried at 60°C for 20 h and remeasured. The results showed that the dioxolanes were suitable with many of the elastomers and that the performances were essentially the same for both molecules. The dioxolanes were found to either have negligible impact beyond neat diesel or they produced a small increase in swell. This minimal impact is attributed to the fact that the solubility parameters (especially those associated with polarity and hydrogen bonding) of the dioxolanes are similar to those of diesel. As a result, little change in solubility and hence swell occurred when dioxolane was added to the diesel.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Amidoxime-functionalized materials and their use in extracting metal ions from liquid solutions

A method of producing a functionalized material that extracts metal ions from solution, the method comprising: (i) providing a precursor material having nitrile groups appended to its surface; and (ii) reacting said nitrile groups with hydroxylamine or a derivative thereof in the presence of a polar aprotic solvent at a temperature of 60-80° C. for at least 1 hour, to convert at least a portion of said nitrile groups to amidoxime and imide dioxime groups, followed by reaction with a base capable of hydrolyzing any remaining nitrile groups to carboxylic acid groups; wherein said functionalized material has a higher uranium absorption capacity than a functionalized material produced under same conditions except that the nitrile groups are reacted with hydroxylamine in only a protic solvent. The invention is also directed to functionalized materials produced by the above-described method, and methods for using the functionalized material for extracting metal ions from metal-containing solutions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A highly efficient uranium grabber derived from acrylic fiber for extracting uranium from seawater

Acrylic fiber can be chemically converted to an am- idoxime and carboxylate containing chelating adsorbent for extraction of uranium from seawater. At an optimized ratio of amidoxime:carboxylate, the chelating fiber in real seawater shows a higher uranium, shorter saturation time and lower vanadium adsorption capacity relative to similar high-surface area chelating fibers developed recently using a radiation-induced grafting method. This simple and low-cost synthesis method can be scaled up to mass produce the chelating fiber for recovering metals from aquatic environments including production of uranium from seawater.

Pan, H B.↗
NASA NTRS1997

Electron Beam Cured Epoxy Resin Composites for High Temperature Applications

Electron beam curing of Polymer Matrix Composites (PMC's) is a nonthermal, nonautoclave curing process that has been demonstrated to be a cost effective and advantageous alternative to conventional thermal curing. Advantages of electron beam curing include: reduced manufacturing costs; significantly reduced curing times; improvements in part quality and performance; reduced environmental and health concerns; and improvement in material handling. In 1994 a Cooperative Research and Development Agreement (CRADA), sponsored by the Department of Energy Defense Programs and 10 industrial partners, was established to advance the electron beam curing of PMC technology. Over the last several years a significant amount of effort within the CRADA has been devoted to the development and optimization of resin systems and PMCs that match the performance of thermal cured composites. This highly successful materials development effort has resulted in a board family of high performance, electron beam curable cationic epoxy resin systems possessing a wide range of excellent processing and property profiles. Hundreds of resin systems, both toughened and untoughened, offering unlimited formulation and processing flexibility have been developed and evaluated in the CRADA program.

Janke, Christopher J.↗