Search NASA⌕ Search

Engineering topics

Jared C Duensing

Publications and source records attributed to Jared C Duensing.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Comparison of Computational Predictions of the Mach 0.80 Transonic Truss-Braced Wing Configuration with Experimental Data

The NASA Langley and Ames Research Centers have teamed together for comparisons of computational predictions of the Boeing Mach 0.80Transonic Truss-Braced Wing (TTBW) configuration with a high-speed experimental dataset. The Mach 0.80 TTBW vehicle is a high wing, high aspect ratio configuration, designed for a high lift-to-drag ratio. System studies have predicted significant fuel burn and emissions benefits with the TTBW technology moving toward meeting NASA Subsonic Transport Systems-Level-Metrics. A 4.5% scale Mach 0.80 design TTBW model was recently tested at the NASA Ames Research Center 11-by 11-Foot Transonic Wind Tunnel(11-Ft TWT),providing a valuable dataset to validate computational tools and investigate best practices as risk reduction efforts continue for the development of the advanced TTBW vehicle. The NASA Computational Fluid Dynamics (CFD) team has computed free-air flow solutions on the Mach 0.80 design flight configuration and two wind tunnel configuration variants using the USM3D and LAVA flow solvers. Accurate modeling of the configuration tested in the wind tunnel environment is critical to validating the CFD tools, thus the team has included the internal cavity region and sting in their modeling of the configuration, similar to that tested in the 11-Ft TWT. Overall, the CFD simulations compared well and show similar trends as the corrected experimental data for lift and drag polars. The CFD predicted lift curve is shifted in angle of attack from what was observed in the experiment. The shift in lift also was seen in the pitching moment comparison plots. CFD solutions were computed at constant CL test point values and showed overall very good agreement when comparing constant spanwise cuts of pressure coefficient data on the wing and strut with experimental data. CFD cavity corrections were also investigated using the 11-Ft TWT cavity correction method, similar to that used to correct the wind tunnel data. Results showed some improvement in pitching moment coefficient predictions, and an increase in drag, shifting the data to the right in drag polars, further from the experimental data at lower lift conditions, good agreement near the design CL, and slight improvement at the higher lift conditions.

Transonic Truss-Braced Wing↗
NASA NTRSDate not supplied

Structured Overset and Unstructured Grid Simulations for the Third AIAA Sonic Boom Prediction Workshop

Predictions using the Launch Ascent and Vehicle Aerodynamics (LAVA) Unstructured and Structured Curvilinear solvers for the Biconvex and C608 geometries are compared in support of the 3rd AIAA Sonic Boom Prediction workshop. Description of the mesh generation techniques and numerical methods are provided along with a comparison of nearfield and far-field predictions with available experimental data as well as other workshop sub-missions. Strong consistency was observed between the Biconvex and C608 nearfield predictions across the two solvers used for this study, as well as validation and verification data. Additionally, near-field and farfield ground signature results using a combination of a truncated computational fluid dynamics (CFD) domain coupled to a mid-field space marching method and propagated to the ground using sBOOM will be discussed. This approach is shown to provide an efficient way to propagate near-field pressure signatures to the ground with the same accuracy as the near-field CFD coupled to sBOOM, but at less computational cost.

CST↗
NASA NTRSDate not supplied

High-Fidelity Aerodynamic Analysis and Optimization of the SUSAN Electrofan Concept

The Subsonic Single Aft Engine (SUSAN) Electrofan is a new single-aisle regional jet class transport aircraft being studied by NASA, which benefits from reduced fuel consumption through a reduction in the number of hydrocarbon fuel-burning engines from two to one. This is achieved through a hybrid-electric system architecture, where a series of generators are used to extract power from a fuel-consuming tail cone thruster to drive electric propulsors mounted on the wings. To support the development of these propulsion systems, which involve high levels of propulsion-airframe integration, this paper presents high-fidelity analyses through computational fluid dynamics (CFD) simulations provided by the Launch Ascent and Vehicle Aerodynamics (LAVA) framework, which also includes capabilities for modeling the effect of active propulsors. A trade space exploration is performed to investigate the advantages of several wing mounted distributed electric propulsion system configurations, including over-wing, under-wing, and trailing-edge arrangements. For the aft fuselage propulsor, focus is on the sizing of the inlet, core, and bypass ducts. High-fidelity aerodynamic shape optimization is also used to help minimize the inlet distortion intensity experienced by the aft propulsor fan through a reshaping of the fuselage.

CAS↗
NASA NTRSDate not supplied

Computational Aerodynamic Analysis in Support of the CRM Tail Cone Thruster Configuration Wind Tunnel Test

NASA’s Advanced Air Transport Technology (AATT) project is breaching the boundaries of aircraft design in pursuit of eco-friendly solutions that are compatible with urban noise comfort levels. Boundary layer ingesting (BLI) propulsion systems promise to reduce fuel burn with additional potential benefits in noise reduction. Type-II BLI systems of the STARC-ABL type are the subject of a test campaign planned for fiscal year 2022 in the National Transonic Facility (NTF), for which a CRM-based model with a retrofitted tail cone thruster (TCT) has been designed. The present work is a precursor to the NTF test, where the 240 cases planned for the experiment were simulated using the Launch, Ascent and Vehicle Aerodynamics (LAVA)computational framework. Solution sensitivity to angle of attack, engine operating conditions, and the presence of the supporting structure (sting) in the wind tunnel test are analyzed in the extensive dataset. The main flow features contributing to the inlet distortion are identified as the vertical tail wake, wing downwash and fuselage upsweep vortices, with the latter two experiencing the greatest sensitivity to angle of attack. Finally, results from an inlet-guide-vane(IGV) design/integration study are presented. The LAVA team and the turbomachinery design team at NASA’s Ames and Glenn Research Centers are collaborating in an effort to reduce flow distortion upstream of the fan by means of integrating an IGV system into the CRM-TCT model. A significant improvement in flow distortion metrics has been achieved since the initial design iteration. Results employing an actuator zone model with realistic radially-varying thrust profiles to simulate first-order fan effects within LAVA are presented.

AATT↗
NASA NTRSDate not supplied

High-Lift Common Research Model: RANS, HRLES and WMLES Perspectives for CLmax Prediction Using LAVA

A unified assessment of three turbulence treatments: Reynolds Averaged Navier-Stokes(RANS), Hybrid RANS/LES (HRLES) and Equilibrium Wall-Modelled Large Eddy Simulation(WMLES) is presented for the High-Lift Common Research Model (CRM-HL). For the free-air configuration, steady-state RANS simulations show very accurate drag polar predictions in the low-𝛼linear regime. However, strong grid sensitivity is reported near the maximum lift-state(𝐶𝐿max), with finer-grids showing larger errors and predicting erroneous flow topologies on the wing. Our RANS simulations show that several corrections for the Spalart-Allmaras (SA)turbulence model widely used in the community lead to more erroneous results compared to the baseline closure, without exception. Both scale-resolving methods (HRLES and WMLES)address these drawbacks and predict an outboard separation pattern on the main element that is in good agreement with the oil flow photographs taken from the QinetiQ wind tunnel experiments, when LES-appropriate grids and numerical discretizations are used. While RANS simulations with the baseline SA closure do not show any wing-root separation post𝐶𝐿max, both HRLES and WMLES show onset of corner flow separation with varying degrees of progression, along with a weak pitch break in the wing-contribution of the overall pitching moment. This post-𝐶𝐿max pitch break seen in the free-air simulations is weaker than the break observed in experiments, with a weaker break reported in WMLES for each iteration of grid-refinement. In-tunnel simulations using both SA-baseline RANS and WMLES show a much stronger post-𝐶𝐿max break with the WMLES predictions showing excellent agreement with the experiment in terms of both the flow-topology observed and the pressure-coefficients at various spanwise stations. Sensitivity to the tunnel wall boundary layer is characterized via comparisons between viscous and inviscid treatments for the tunnel walls. WMLES predictions show moderate sensitivity at the predicted inboard flow-state at 𝐶𝐿max along with the progression towards a post-𝐶𝐿max stall; however, this stalled state at 𝛼≈20◦(inside the tunnel) obtained with both tunnel wall treatments appears to be largely identical.

TTT↗
NASA NTRSDate not supplied

Brief Overview of Subsonic Single Aft Engine (SUSAN) Transport Aircraft Concept and Trade Space Exploration

The SUSAN concept uses a 20-megawatt Electrified Aircraft Propulsion system to enable advance Propulsion Airframe Integration in transport category aircraft. Alternative fuels will be used to reduce the amount of emissions per energy used. By combining these features there is the potential to reduce aircraft emissions by 50 percent per passenger/mile while retaining the size, speed, and range of large regional jets. The SUSAN is has a 750-mile economic mission, a 2500-mile design range and a maximum capacity of 180 passengers. The SUSAN configuration utilizes a single aft mounted engine and distributed electric wing-mounted thrusters on a tube and wing arrangement with a T-tail empennage. The SUSAN Electrofan employs a hybrid powertrain to enable: single turbofan operation on a large transport category aircraft; increased aerodynamic and propulsive efficiency through placement of electric engines; optimized turbofan sizing and efficiency through control and electric boosting, reduced control surface sizing through thrust augmentation. A single use battery is employed as the power source in case of turbofan failure. The design study also considers the constraints of operating within the current airport, airspace, and economic constraints. Forward work includes optimizing the overall aircraft configuration and including certain hard to model features like boundary layer ingestion or natural laminar flow across all appliable subsystems. Additional work forward work is a more extensive analysis of the configuration using alternative fuels.

Ralph Jansen↗
NASA NTRSDate not supplied

A Reynolds-Averaged Navier-Stokes Perspective for the High Lift Common Research Model Using the LAVA Framework

An in-depth assessment of the High Lift-Common Research Model (HL-CRM) aerodynamic performance is made using a Reynolds-Averaged Navier-Stokes (RANS) methodology. Results presented here were produced in support of the 4th AIAA High Lift Prediction Workshop(HLPW-4), with additional simulation results and analysis used to support findings from the workshop. Mesh resolution, RANS closure models, and tunnel effects were among the sources of simulation sensitivity addressed, all in the pursuit of evaluating best-practice simulation methods for complex high-lift configurations. In general, free-air simulations using RANS yield accurate predictions of integrated loads in the pre-stall regime for the HL-CRM, while strong sensitivity to simulation method is observed near CLmax. Additionally, a study assessing changes in aerodynamic performance due to flap deflection angle indicated strong sensitivity to turbulence model closure and mesh resolution, particularly at the highest deflection setting. Several available corrections for the Spalart-Allmaras (SA) turbulence model were tested and generally introduced more error relative to the experiment in comparison to the baseline SA closure model. The Standard Menter Baseline Two-Equation (k-ωBSL) turbulence model was also explored, which arguably yielded results highly consistent with experiment, but at a substantially higher computational cost. Therefore, as a compromise between computational cost and accuracy, the baseline SA closure model was selected for additional HL-CRM studies that assess alternative solution methods. These strategies include “warm start” approaches, which initialize the simulation from a previously converged solution at a nearby angle of attack, unsteady calculations, and simulations that model the experimental wind tunnel. Results from these studies would reinforce the shortcomings of RANS in predicting aircraft performance at high-lift conditions, namely at high-αand highly loaded flap conditions, while also answering questions about appropriate modeling techniques to minimize the errors associated with RANS where possible

TTT↗
NASA NTRSDate not supplied

Validation of Actuator Disk, Actuator Line and Sliding Mesh Methods within the LAVA Solver

In this study the implementation of actuator-disk, actuator-line and sliding-mesh methodologies in the Launch Ascent and Vehicle Aerodynamics (LAVA) solver is described and validated against several test-cases. The different models are validated against available numerical as well as experimental data. Both steady and unsteady Reynolds-Averaged Navier-Stokes (RANS) simulations using the Spallart Allmaras (SA) turbulence model are performed for several different configurations representative of aeroscience applications. The first part of the paper is focused on the verification and validation of the implemented propulsor models. The first validation case is a theoretical rotor in hover, compared with the 1D analytical solution derived from momentum theory. The second validation is the Rotor-Airframe Interaction Model of Georgia Institute of Technology (GIT), representing the application of actuator disks to top-mounted rotorcraft vehicles or unmanned aerial vehicles (UAVs). The third case is a representative configuration for tip-mounted rotor-craft vehicles such as NASA’s X57 airplane. The second part of the paper shows the implemented models applied to realistic engineering configurations such as NASA’s X57 airplane and the R4 Advanced Ducted Propellor (ADT). A modification to the actuator line method in order to represent the blade geometry more closely is proposed and comparisons with simulations modeling the blade utilizing a sliding-mesh approach are made.

ARMD↗
NASA NTRSDate not supplied

Noise Prediction of Multi-stream Internally Mixed Jets with External and Internal Plugs using Large-Eddy Simulation

This paper presents results from ongoing research on jet noise prediction using wall-modeled large eddy simulations (WMLES) conducted within the Launch Ascent and Vehicle Aerodynamics (LAVA) computational framework. The study primarily focuses on the aeroacoustic implications of multi-stream nozzle configurations with internal mixing and both internal and external plugs, at a Reynolds number of 1×10 6 based on the nozzle exit diameter. While internal mixing nozzles have long been considered for jet noise reduction, the complexities of their impact on overall noise levels remain insufficiently understood. This research applies established best practices for WMLES to these complex nozzle configurations, aiming to assess their efficacy and identify limitations in accurately predicting noise behaviors. Through detailed comparisons with experimental data obtained from NASA’s Glenn Research Center, initial findings underscore the challenges inherent in current simulation practices when confronted with intricate geometric and operational conditions. Responding to these challenges, the study explores innovative computational approaches to rectify discrepancies noted between experimental outcomes and CFD predictions. Once example is the introduction of a resonating sound source in the simulation environment to mimic potential unobserved acoustic phenomena.A second example is the strategic modifications to the geometry of external plugs to account for real-world deformations caused by heating and gravity. These novel strategies aim to enhance the accuracy and reliability of noise predictions from supersonic jets, advancing our understanding and capability to effectively reduce jet noise in commercial supersonic aircraft

CST↗
NASA NTRSDate not supplied

Wall-Modeled Large-Eddy Simulations of a Swept Wing with Leading-Edge Ice

The aerodynamic performance of a swept wing derived from the Common Research Model wing with high-fidelity and smooth leading-edge ice shapes is evaluated using wall-modeled large-eddy simulations. Two mesh paradigms are considered within the Launch, Ascent, and Vehicle Aerodynamics framework: structured hybrid curvilinear body-fitted/immersed-boundary and unstructured Voronoi. The curvilinear approach models the effect of the ice on the flow through penalty terms and the Voronoi strategy includes the ice representation directly in the mesh.Aerodynamic loads, surface pressure profiles, and skin-friction streamlines are compared against experimental results collected at the Wichita State University wind tunnel at a Mach number of 0.18 and a Reynolds number per mean aerodynamic chord of 1.6 million. For the curvilinear simulations with high-fidelity ice, results are sensitive to spanwise mesh resolution near the leading edge, where insufficient spanwise resolution leads to a spanwise running vortexaft of the high-fidelity ice, which is partially removed with increasing spanwise resolution. For the Voronoi simulations with high-fidelity ice, refining the mesh led to good convergence towards the experimental results with the best case demonstrating a maximum discrepancy of three lift counts relative to the experiment across a range of angles of attack from about 5 to 24 degrees, validating the shrink-wrapping procedure used for the ice. For the smooth ice, the curvilinear approach consistently under-predicted the upper surface suction leading to an under-prediction in lift, but did not demonstrate the pronounced over-prediction in upper surface suction near the leading edge observed in the Voronoi simulations.

AATT↗