Engineering topics

Jarred M Wilhite

Publications and source records attributed to Jarred M Wilhite.

4 records

NASA NTRSDate not supplied

Thermal Environments and Margin Guidelines for NASA’s X-57 “Maxwell” Flight Demonstrator

NASA’s X-57 project includes development and flight demonstration of new electrified propulsion systems and equipment. The system components are designed to operate without active thermal management, which places increased emphasis on the ambient conditions as well as environmental stress screening for the newly designed equipment. Since the X-57 will not be operated outside of the Dryden Aeronautical Test Range at NASA’s Armstrong Flight Research Center, the X-57 team developed a series of reference atmospheres, described in this paper, based on the 2019 Edwards Range Reference Atmosphere to guide system development and testing. These four reference atmospheres include a standard day reference atmosphere that is identical to the 1976 U. S. Standard Atmosphere, a mean operational day atmosphere based on the mean 2019 Edwards Range Reference Atmosphere, and hot and cold day atmospheres based on the ±2σ yearly temperature variations in the Edwards Range Reference Atmosphere. As described herein, these reference atmospheres were then used to develop anticipated operational extremes for thermal cycle testing for the X-57 systems, which were developed from an amalgamation of two standards:SMC-S-016 and DO-160G. The project also adopted thermal margin guidance from SMC-S-016 to set requirements for the development of new electrified propulsion system components.

Thermal environments↗

NASA NTRSDate not supplied

Hybrid Electric Turboprop Commercial Freighter Opportunity

As the era of electric and hybrid electric aviation is dawning, we have the opportunity to reduce cost, energy use, and emissions of air transportation. In this paper, the case is made for the potential efficiency benefits that can be gained with hybrid electric propulsion. Initial economic, mission profile, and propulsion system concepts for a large turboprop aircraft we designate as the Hybrid Electric Turboprop Commercial Freighter (HETCOF) are presented. Market analysis shows HETCOF has the potential to serve a large market share, but the cost requirements for a new purpose built are challenging relative to the repurposed narrow body aircraft currently operating in the market. Comparing HETCOF to a genericized large turboprop freighter the payload capacity is reduced by 40% for the TRL 5+ configuration but is equivalent to the baseline for the TRL 1-2 configuration. All HETCOF configurations result in increased efficiency and subsequent block fuel, block energy, and block emissions reductions. An integrated power/thermal/and energy storage system is presented and analyzed using key performance parameters to estimate weights and losses at three technology readiness levels. Analysis shows that for a concept like this to have economic and energy benefits, many TRL 1-2 level technologies would be needed. Relevant ARPA-E programs and NASA technologies being developed to enable the benefit are also described. The most significant result of this paper is that the HETCOF concept can close with reduced fuel burn, energy use, and emissions while retaining some or all of the cargo capability of the baseline aircraft across TRL level assumptions, which enables this platform to be used for near term introduction with increasing benefits as technology matures.

Ralph H Jansen↗

NASA NTRSDate not supplied

Selecting an Encapsulant for an Aerospace Superconducting Machine

Achieving larger benefits from electrified propulsion in single aisle aircraft (the largest commercial aircraft market segment) necessitates that a significant fraction of their 20 MW or greater propulsion system be electrified. 5 to possibly 20 of the MW-scale electric machines investigated by NASA would be required to meet this need. Approximately 10-20 of NASA’s MW-scale electric machines would be required to reach the necessary power levels. Therefore, electric machines of 5 MW or greater are of interest. However, conventionally cooled high power density MW-scale electric machines still produce a significant amount of waste heat, which makes obtaining these power levels problematic. Highly efficient fully superconducting electric machines (or those with a cryogenically cooled, high purity copper or aluminum stator) are a possible solution but have multiple barriers to be overcome. One such barrier is the durability of superconducting windings. Superconductors are typically brittle, and encapsulants used to hold windings in place are a significant source of stress because of the mismatches in coefficient of thermal expansion at temperatures between room temperature and operational temperatures (20 to 77 K). These encapsulants also form a thermal barrier that can be detrimental to cooling the superconductors. This paper describes an initial study of commercially available encapsulants as it relates to superconducting machine applications along with initial modeling of thermal stress in superconducting windings for a superconducting or cryogenically cooled stator in a 5 MW electric machine.

encapsulant↗

NASA NTRSDate not supplied

Selecting an Encapsulant for an Aerospace Superconducting Machine

Achieving larger benefits from electrified propulsion in single aisle aircraft (the largest commercial aircraft market segment) necessitates that a significant fraction of their 20 MW or greater propulsion system be electrified. These aircraft would require up to 10-20 of today’s state-of-the art machines, which have been demonstrated up to 2.5 MW for aerospace use, and could benefit further from 5 MW+ designs. However, when conventionally cooled, high power density machines still produce a significant amount of waste heat, translating into heavy thermal management and detracting from system benefits. Highly efficient fully superconducting electric machines (or those with a cryogenically cooled, high purity copper or aluminum stator) are a possible solution but have multiple barriers to overcome. One such barrier is the durability of superconducting windings. Superconductors are typically brittle, and encapsulants used to hold windings in place are a significant source of stress due to mismatches in coefficient of thermally induced contraction between ambient and operational temperatures (20 to 77 K). Lack of compliance between the materials at operational temperatures also adds significant stress. These encapsulants also form a thermal barrier that can be detrimental to cooling the superconductors. This work describes an initial study of commercially available encapsulants as it relates to superconducting machine applications, along with initial modeling of thermal stress in superconducting windings for a superconducting or cryogenically cooled stator in a 5 MW electric machine.

encapsulant↗