Engineering topics
Publications and source records attributed to Javadi, H. H. S..
A deep space satellite downconverter receiver was proposed by Jet Propulsion Laboratory (JPL) and NASA Lewis research Center (LeRC) for the Naval Research Laboratory's (NRL) High Temperature Superconductivity Space Experiment, phase-ii (HTSSE-II) program....
An experiment has been devised which will validate, in space, a miniature, high-performance receiver. The receiver blends three complementary technologies; high temperature superconductivity (HTS), pseudomorphic high electron mobility transistor (PHEMT) monolithic microwave integrated circuits (MMIC), and a miniature pulse tube cryogenic cooler. Specifically, an HTS band pass filter, InP MMIC low noise amplifier, HTS-sapphire resonator stabilized local oscillator (LO), and a miniature pulse tube cooler will be integrated into a complete 20 GHz receiver downconverter. This cooled downconverter will be interfaced with customized signal processing electronics and integrated onto the space shuttle's 'HitchHiker' carrier. A pseudorandom data sequence will be transmitted to the receiver, which is in low Earth orbit (LEO), via the Advanced Communication Technology Satellite (ACTS) on a 20 GHz carrier. The modulation format is QPSK and the data rate is 2.048 Mbps. The bit error rate (BER) will be measured in situ. The receiver is also equipped with a radiometer mode so that experiment success is not totally contingent upon the BER measurement. In this mode, the receiver uses the Earth and deep space as a hot and cold calibration source, respectively. The experiment closely simulates an actual cross-link scenario. Since the receiver performance depends on channel conditions, its true characteristics would be masked in a terrestrial measurement by atmospheric absorption and background radiation. Furthermore, the receiver's performance depends on its physical temperature, which is a sensitive function of platform environment, thermal design, and cryocooler performance. This empirical data is important for building confidence in the technology.
We have measured the effects of dispersion on the resonant mode frequencies of open-ended Nb-SiO(x)-Nb microstrip transmission lines over a frequency range from 50 to 800 GHz. Submicron Nb/Al-AlOx/Nb Josephson junctions were used as both voltage-controlled oscillators and detectors to sample the high order modes of the resonators. The resonator modes are equally spaced up to about 550 GHz where the mode spacing start to decrease gradually to a minimum above the gap frequency of about 700 GHz and then increases. Results are in good agreement with the expected theoretical behavior based on the Mattis-Bardeen conductivity of the superconductor line.
We have measured the dispersion in phase velocity of a Nb-SiO(x)-Nb microstrip transmission line resonator over a frequency range from 50 GHz to 800 GHz. A submicron Nb/Al-AlO(x)/Nb Josephson junction was used as a voltage-controlled oscillator to excite the high order modes in the resonator. The same junction is used as a direct detector resulting in a series of step-like structures in the DC current-voltage characteristic at the position of each mode frequency. The transmission line is dispersionless up to about 500 GHz where the phase velocity begins to decrease. This is well below the gap frequency f(sub g) approx. equals 700 GHz. Results agree qualitatively with the expected theoretical behavior near f(sub g). This onset of dispersion and loss in Nb transmission lines will have a significant impact on the design of submillimeter wave RF circuits.
Small area (less than 1 sq micron), high-current-density NbN/MgO/NbN tunnel junctions with I-V characteristics suitable for high-frequency mixers have been fabricated. Mesa-geometry junctions with an area of about 1 sq micron and critical current density of 5-10 kA/sq cm are integrated with superconducting microstrip lines designed to resonate out the junction capacitance. A study was made of the mixer gain and noise performance near 205 GHz as a function of the inductance provided by the microstrip line. This has confirmed, at a high millimeter-wave frequency, values of junction capacitance of 85 fF/sq micron and recently measured values of a magnetic penetration depth of 380 nm. Mixer noise temperatures as low as 134 K at 1.5 K have been obtained for properly tuned junctions. A significant improvement in mixer performance on cooling from 4.2 K to 1.5 K was observed. Edge-geometry junctions with an area of 0.3 sq microns and critical current density of 18-25 kA/sq cm have also been fabricated. These junctions give a mixer noise temperature of 145 K at 4.2 K without the use of integrated tuning elements. These are the best results ever achieved for NbN-based SIS mixers.