Search NASA⌕ Search

Engineering topics

Jennings, C. A.

Publications and source records attributed to Jennings, C. A..

10 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Integrated simulations of premagnetized and self-magnetizing dynamic screw pinch-driven MagLIF

Magnetically driven implosions such as in magnetized liner inertial fusion (MagLIF) on the Z accelerator suffer from magneto-Rayleigh–Taylor instabilities (MRTI) that dynamically redistribute liner mass during implosion, limiting fusion fuel compression and confinement, which ultimately degrades performance. Driving the implosion with an initially helical drive field that dynamically shifts the direction of the magnetic field surrounding the liner (i.e., a dynamic screw pinch, DSP) is a method proposed to mitigate MRTI in-flight and improve target performance. In DSPs, the axial drive magnetic field component implodes the liner and diffuses through the shocked, melted liner material into the fuel throughout the implosion. Liners can be designed to enable enough axial magnetic flux to diffuse through the liner material to effectively magnetize the fuel region without the need of an initial axial magnetic field (i.e., from external field coils). We present results from three-dimensional radiation-magnetohydrodynamic simulations of MagLIF implosions employing drive magnetic fields composed of axial and azimuthal components (a helical drive field). These simulated DSP-driven MagLIF targets demonstrate improved fuel conditions and thermonuclear yield compared to a traditional MagLIF target implosion. Synthetic x-ray radiography of the imploding liner material and x-ray emission images of the fuel region at the time of peak neutron yield rate indicate superior implosion morphology for DSP-MagLIF implosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Simulated thermonuclear performance of auto-magnetizing helical liner MagLIF target implosions

Magnetized liner inertial fusion (MagLIF) implosions on the Z accelerator require magnetization of the fuel to reduce thermal conduction losses of energy from the laser-preheated deuterium fusion fuel to the surrounding liner material. While external field coils traditionally used to axially magnetize MagLIF targets are limited to 10–20 T (or perhaps ∼ 30 T with technological development), calculations suggest that higher axial magnetic fields would improve thermal insulation of the fuel and improve MagLIF target performance. We present results from three-dimensional radiation-magnetohydrodynamic simulations of MagLIF implosions employing auto-magnetizing helical liners composed of discrete metallic helical conduction paths separated by electrically insulating material. These simulated auto-magnetizing (AutoMag) liners produce axial magnetic fields >30 T inside the fusion fuel prior to implosion. Simulations indicate that higher thermonuclear yields and burn-averaged fuel ion temperatures are attained for implosions using AutoMag liners compared to standard MagLIF implosions. Comparable implosion morphology is evident in synthetic x-ray images of AutoMag–MagLIF and standard MagLIF implosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Magnetized liner inertial fusion platform development to assess performance scaling with drive parameters

Magnetized liner inertial fusion (MagLIF) experiments have demonstrated fusion-relevant ion temperatures up to 3.1 keV and thermonuclear production of up to 1.1 × 1013 deuterium–deuterium neutrons. This performance was enabled through platform development that provided increases in applied magnetic field, coupled preheat energy, and drive current. Advanced coil designs with internal reinforcement enabled an increase from 10 to 20 T. An improved laser pulse shape, beam smoothing, and thinner laser entrance foils increased preheat energy coupling from less than 1 to 2.3 kJ. A redesign of the final transmission line and load region increased peak load current from 16 to 20 MA. The wider range of input parameters was leveraged to study target performance trends with preheat energy, applied magnetic field, and peak load current. Ion temperature and neutron yield generally followed trends in two-dimensional clean Lasnex calculations. Stagnation performance improved with peak load current when other input parameters were also increased such that convergence was maintained. This dataset suggests that reducing convergence to less than 30 would improve predictability of target performance. Lasnex was used to identify a simulation-optimized scaling path, which suggests 10+ kJ of fusion yield is possible on the Z facility with achievable input parameters. This path also indicates >10 MJ could be generated through volume burn on a future facility with a path to high yield (>200 MJ) using cryogenic dense fuel layers. The newly developed MagLIF platform enables exploration of both this simulation optimized scaling path and a recently developed similarity-scaling path.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Understanding the impact of an applied axial magnetic field on efficient current coupling on the Z machine

Magnetized liner inertial fusion (MagLIF) is an attractive concept for producing thermonuclear fusion reactions. The MagLIF platform involves the operation of Helmholtz coils to apply a 15 Tesla axial magnetic field to the load region, where a cylindrical, fuel-filled metal liner is imploded by a ∼ 2 0 MA current pulse. The fringe field from these coils extends into the transmission line that delivers the current to the target. We investigated the extent to which this applied field disturbs the nominal power flow within that transmission line. A simplified model of the geometry shows that adding the applied magnetic field results in magnetic field lines that connect the cathode to the anode, suggesting electrons may not be magnetically insulated in this region. Particle-in-cell simulations indicated the addition of the applied magnetic field would not significantly impact the current delivery to the load. Velocimetry was used to experimentally assess the current delivery with and without the applied magnetic field. We find no measurable effects of the applied field on current delivery in the configuration investigated in this study. Published by the American Physical Society 2024

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Development of a high performance MagLIF target platform using high aspect ratio coated liners and low-mix laser preheat

We report on a series of Magnetized Liner Inertial Fusion (MagLIF) experiments conducted on the Z pulsed power facility that utilized high aspect ratio (ratio of outer radius to wall thickness) liners with dielectric coatings and low-mix laser preheat configurations. The liners consisted of an aspect ratio of 10.6 beryllium tube coated with 75 μm of epoxy on the outside that have been shown to maintain a better implosion stability than uncoated beryllium and have demonstrated consistent stagnation performances in previous experiments [Ampleford et al., Phys. Plasmas 31, 022703 (2024)]. Two-dimensional HYDRA simulations were used to design three different “co-injection” laser configurations, whereby a second laser is used to provide an early prepulse before the main pulse, to reduce LEH foil mix while increasing the fuel density and coupled energy. The laser preheat energy for each configuration was constrained using dedicated laser experiments before being applied to the integrated MagLIF experiments on Z. The DD neutron yield for experiments using co-injection preheat configurations is found to increase with the specific preheat energy in line with simulations. The highest neutron yield achieved in this study of 1.1 × 10 13 matches the highest reported in a MagLIF experiment to date and is a factor 3.5 times higher than similar experiments using preheat with no phase plate smoothing. We attempt to assess the effects of mix and morphology to explain the improved performance; however, neither factor is found to be conclusive within the uncertainty of the measurements.

Harvey-Thompson, A. J.↗
DOE OSTI2024

Radiatively cooled magnetic reconnection experiments driven by pulsed power

We present evidence for strong radiative cooling in a pulsed-power-driven magnetic reconnection experiment. Two aluminum exploding wire arrays, driven by a 20 MA peak current, 300 ns rise time pulse from the Z machine (Sandia National Laboratories), generate strongly driven plasma flows (MA≈7) with anti-parallel magnetic fields, which form a reconnection layer (SL≈120) at the mid-plane. The net cooling rate far exceeds the Alfvénic transit rate (τcool−1/τA−1≫1), leading to strong cooling of the reconnection layer. We determine the advected magnetic field and flow velocity using inductive probes positioned in the inflow to the layer, and inflow ion density and temperature from analysis of visible emission spectroscopy. A sharp decrease in x-ray emission from the reconnection layer, measured using filtered diodes and time-gated x-ray imaging, provides evidence for strong cooling of the reconnection layer after its initial formation. X-ray images also show localized hotspots, regions of strong x-ray emission, with velocities comparable to the expected outflow velocity from the reconnection layer. These hotspots are consistent with plasmoids observed in 3D radiative resistive magnetohydrodynamic simulations of the experiment. X-ray spectroscopy further indicates that the hotspots have a temperature (170 eV) much higher than the bulk layer (≤75 eV) and inflow temperatures (about 2 eV) and that these hotspots generate the majority of the high-energy (>1 keV) emission.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Plasmoid Formation and Strong Radiative Cooling in a Driven Magnetic Reconnection Experiment

Herein we present the first experimental study of plasmoid formation in a magnetic reconnection layer undergoing rapid radiative cooling, a regime relevant to extreme astrophysical plasmas. Two exploding aluminum wire arrays, driven by the Z machine, generate a reconnection layer (S L ≈ 120) in which the cooling rate far exceeds the hydrodynamic transit rate (τ hydro =τ cool > 100). The reconnection layer generates a transient burst of >1 keV x-ray emission, consistent with the formation and subsequent rapid cooling of the layer. Time-gated x-ray images show fast-moving (up to 50 km s –1 ) hotspots in the layer, consistent with the presence of plasmoids in 3D resistive magnetohydrodynamic simulations. X-ray spectroscopy shows that these hotspots generate the majority of Al K-shell emission (around 1.6 keV) prior to the onset of cooling, and exhibit temperatures (170 eV) much greater than that of the plasma inflows and the rest of the reconnection layer, thus providing insight into the generation of high-energy radiation in radiatively cooled reconnection events.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Controlling morphology and improving reproducibility of magnetized liner inertial fusion experiments

X-ray imaging indicates magnetized liner inertial fusion (MagLIF) stagnation columns have a complicated quasi-helical structure with significant variations in x-ray brightness along the column. In this work, we describe MagLIF experiments aimed at controlling these stagnation structures by varying the initial liner geometry and composition. First, by varying the initial aspect ratio of the liner, we demonstrate a change in the stagnation structures that is consistent with helical magneto Rayleigh–Taylor (MRT) instabilities feedthrough from the outer-to-inner surfaces of the liner. Second, to minimize the seed for such instabilities, we incorporate a dielectric coating on the outer surface of the beryllium liner, which has previously been shown to reduce the growth of the electrothermal instability, a likely seed for MRT growth. Using this coating, we achieve a stagnation column with significantly reduced helical structure and axial variation in x-ray brightness. We discuss how this coating changes the evolution of structures through stagnation along with the spatial uniformity of neutron production. Finally, we show that these more uniform stagnations also result in improved reproducibility in stagnation temperatures and primary DD neutron yield.

Ampleford, D. J. (ORCID:0000000237422421)↗
DOE OSTI2024

Numerical study of implosion instability mitigation in magnetically driven solid liner dynamic screw pinches

Magnetized liner inertial fusion experiments on the Z accelerator suffer from magneto-Rayleigh–Taylor instabilities (MRTI) that compromise integrity of the imploding cylindrical liner, limiting achievable fusion fuel conditions and ultimately reducing magneto-inertial fusion target performance. Dynamic screw pinches (DSP) provide a method to reduce MRTI in-flight via application of magnetic field line tension to the imploding liner outer surface. In contrast with z-pinches that drive implosions with an azimuthal magnetic field, dynamic screw pinches enforce an additional axial drive magnetic field component, making the overall drive magnetic field helical. As the liner implodes, cumulative MRTI development is reduced by dynamically shifting the orientation of the fastest growing instability modes. Three-dimensional magnetohydrodynamic simulations show that the DSP mechanism effectively stabilizes initially solid cylindrical liner implosions driven by Z-scale current pulses, indicating that MRTI mitigation increases with the ratio of axial to azimuthal drive magnetic field components (i.e., the drive field ratio). We also performed a spectral analysis of the simulated imploding density distributions, extracting wavelength and pitch angle of the simulated MRTI structures to study their dynamics during the implosion. Simulations of liners initially perturbed with drive-field-aligned sinusoidal structures indicate that MRTI mitigation in DSP implosions decreases with perturbation wavelength, once again suggestive of magnetic field line tension effects.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗