Engineering topics

Jensen, K. A.

Publications and source records attributed to Jensen, K. A..

18 records

NASA NTRS2004

Radiative Transfer Modeling of a Large Pool Fire by Discrete Ordinates, Discrete Transfer, Ray Tracing, Monte Carlo and Moment Methods

Five computational methods for solution of the radiative transfer equation in an absorbing-emitting and non-scattering gray medium were compared on a 2 m JP-8 pool fire. The temperature and absorption coefficient fields were taken from a synthetic fire due to the lack of a complete set of experimental data for fires of this size. These quantities were generated by a code that has been shown to agree well with the limited quantity of relevant data in the literature. Reference solutions to the governing equation were determined using the Monte Carlo method and a ray tracing scheme with high angular resolution. Solutions using the discrete transfer method, the discrete ordinate method (DOM) with both S(sub 4) and LC(sub 11) quadratures, and moment model using the M(sub 1) closure were compared to the reference solutions in both isotropic and anisotropic regions of the computational domain. DOM LC(sub 11) is shown to be the more accurate than the commonly used S(sub 4) quadrature technique, especially in anisotropic regions of the fire domain. This represents the first study where the M(sub 1) method was applied to a combustion problem occurring in a complex three-dimensional geometry. The M(sub 1) results agree well with other solution techniques, which is encouraging for future applications to similar problems since it is computationally the least expensive solution technique. Moreover, M(sub 1) results are comparable to DOM S(sub 4).

Jensen, K. A.↗

NASA NTRS1994

Measurement of the cosmic microwave background spectrum by the COBE FIRAS instrument

The cosmic microwave background radiation (CMBR) has a blackbody spectrum within 3.4 x 10(exp -8) ergs/sq cm/s/sr cm over the frequency range from 2 to 20/cm (5-0.5 mm). These measurements, derived from the Far-Infrared Absolute Spectrophotomer (FIRAS) instrument on the Cosmic Background Explorer (COBE) satellite, imply stringent limits on energy release in the early universe after t approximately 1 year and redshift z approximately 3 x 10(exp 6). The deviations are less than 0.30% of the peak brightness, with an rms value of 0.01%, and the dimensionless cosmological distortion parameters are limited to the absolute value of y is less than 2.5 x 10(exp -5) and the absolute value of mu is less than 3.3 x 10(exp -4) (95% confidence level). The temperature of the CMBR is 2.726 +/- 0.010 K (95% confidence level systematic).

Mather, J. C.↗

NASA NTRS1994

Calibration of the COBE FIRAS instrument

The Far-Infrared Absolute Spectrophotometer (FIRAS) instrument on the Cosmic Background Explorer (COBE) satellite was designed to accurately measure the spectrum of the cosmic microwave background radiation (CMBR) in the frequency range 1-95/cm with an angular resolution of 7 deg. We describe the calibration of this instrument, including the method of obtaining calibration data, reduction of data, the instrument model, fitting the model to the calibration data, and application of the resulting model solution to sky observations. The instrument model fits well for calibration data that resemble sky condition. The method of propagating detector noise through the calibration process to yield a covariance matrix of the calibrated sky data is described. The final uncertainties are variable both in frequency and position, but for a typical calibrated sky 2.6 deg square pixel and 0.7/cm spectral element the random detector noise limit is of order of a few times 10(exp -7) ergs/sq cm/s/sr cm for 2-20/cm, and the difference between the sky and the best-fit cosmic blackbody can be measured with a gain uncertainty of less than 3%.

Fixsen, D. J.↗

NASA NTRS1986

EXOSAT observations of V471 Tauri - A 9.25 minute white dwarf pulsation and orbital phase dependent X-ray dips

New results obtained from a 28 hr continuous observation of V471 Tauri with the EXOSAT satellite are reported. The detection of soft X-ray fluxes from both the white dwarf and the K dwarf, the discovery of a 9.25 minute pulsation from the white dwarf, and the discovery of orbital phase-related soft X-ray dips are discussed. The dips may be correlated with the triangular Lagrangian points of the binary orbit. The X-ray flux from the white dwarf is consistent with thermal models for a white dwarf photosphere with T(eff) of about 35,000 K, log g = 8.0-8.5, and log N(H) = 18.65 + or - 0.2.

Jensen, K. A.↗

NASA NTRS1986

Textured carbon surfaces on copper by sputtering

A very thin layer of highly textured carbon is applied to a copper surface by a triode sputtering process. A carbon target and a copper substrate are simultaneously exposed to an argon plasma in a vacuum chamber. The resulting carbon surface is characterized by a dense, random array of needle like spires or peaks which extend perpendicularly from the copper surface. The coated copper is especially useful for electrode plates in multistage depressed collectors.

Curren, A. N.↗

NASA NTRS1986

Process Produces Low-Secondary-Electron-Emission Surfaces

Textured carbon layer applied to copper by sputtering. Carbon surface characterized by dense, random array of needle-like spires or peaks that extend perpendicularly from local copper surface. Spires approximately 7 micrometers in height and spaced approximately 3 micrometers apart, on average. Copper substrate essentially completely covered by carbon layer, is tenacious and not damaged by vibration loadings representative of multistage depressed collector (MDC) applications. Process developed primarily to provide extremely low-secondary-electron-emission surface for copper for use as highefficiency electrodes in MDC's for microwave amplifier traveling-wave tubes (TWT's). Tubes widely used in space communications, aircraft, and terrestrial applications.

Curren, A. N.↗

NASA NTRS1985

Textured carbon on copper: A novel surface with extremely low secondary electron emission characteristics

Experimentally determined values of true secondary electron emission and relative values of reflected primary electron yield for a range of primary electron beam energies and beam impingement angles are presented for a series of novel textured carbon surfaces on copper substrates. (All copper surfaces used in this study were oxygen-free, high-conductivity grade). The purpose of this investigation is to provide information necessary to develop high-efficiency multistage depressed collectors (MDC's) for microwave amplifier traveling-wave tubes (TWT's) for communications and aircraft applications. To attain the highest TWT signal quality and overall efficiency, the MDC electrode surface must have low secondary electron emission characteristics. While copper is the material most commonly used for MDC electrodes, it exhibits relatively high levels of secondary electron emission unless its surface is treated for emission control. The textured carbon surface on copper substrate described in this report is a particularly promising candidate for the MDC electrode application. Samples of textured carbon surfaces on copper substrates typical of three different levels of treatment are prepared and tested for this study. The materials are tested at primary electron beam energies of 200 to 2000 eV and at direct (0 deg) to near-grazing (85 deg) beam impingement angles. True secondary electron emission and relative reflected primary electron yield characteristics of the textured surfaces are compared with each other and with those of untreated copper. All the textured carbon surfaces on copper substrate tested exhibited sharply lower secondary electron emission characteristics than those of an untreated copper surface.

Curren, A. N.↗

NASA NTRS1985

Soft X-rays, winds, and the cataclysmic variable boundary-layer problem

Models are presented for the effects of a stellar wind on the UV and soft X-ray spectra of cataclysmic variables (CVs). It is shown that P Cygni absorption lines observed from many CVs are consistent with the existence of a strong wind, and that such a wind can also account for the soft X-ray upper limits if the wind mass loss rate is about 10 to the -8th solar masses per yr. The implications of such a wind for the CV momentum and energy budget are discussed.

Kallman, T. R.↗

NASA NTRS1984

Secondary electron emission characteristics of ion-textured copper and high-purity isotropic graphite surfaces

Experimentally determined values of true secondary electron emission and relative values of reflected primary electron yield for untreated and ion textured oxygen free high conductivity copper and untreated and ion textured high purity isotropic graphite surfaces are presented for a range of primary electron beam energies and beam impingement angles. This investigation was conducted to provide information that would improve the efficiency of multistage depressed collectors (MDC's) for microwave amplifier traveling wave tubes in space communications and aircraft applications. For high efficiency, MDC electrode surfaces must have low secondary electron emission characteristics. Although copper is a commonly used material for MDC electrodes, it exhibits relatively high levels of secondary electron emission if its surface is not treated for emission control. Recent studies demonstrated that high purity isotropic graphite is a promising material for MDC electrodes, particularly with ion textured surfaces. The materials were tested at primary electron beam energies of 200 to 2000 eV and at direct (0 deg) to near grazing (85 deg) beam impingement angles. True secondary electron emission and relative reflected primary electron yield characteristics of the ion textured surfaces were compared with each other and with those of untreated surfaces of the same materials. Both the untreated and ion textured graphite surfaces and the ion treated copper surface exhibited sharply reduced secondary electron emission characteristics relative to those of untreated copper. The ion treated graphite surface yielded the lowest emission levels.

Curren, A. N.↗

NASA NTRS1984

Boundary layers in cataclysmic variables - The HEAO 1 X-ray constraints

The predictions of the boundary layer model for the X-ray emission from novae are summarized. A discrepancy between observations and theory in the X-ray observations is found. Constraints on the nature of the boundary layers in novae, based on the lack of detections of novae in the HEAO-1 soft X-ray survey are provided. Temperature and column densities for optically thick boundary layers in novae are estimated. Previously announced in STAR as N84-13046

Jensen, K. A.↗

NASA NTRS1984

Beam impingement angle effects on secondary electron emission characteristics of textured pyrolytic graphite

Experimentally determined values of true secondary electron emission and relative values of reflected primary electron yield for untreated and ion-textured pyrolytic graphite over a range of primary electron energy levels and electron beam impingement angles are presented. Information required to develop high efficiency multistage depressed collectors (MDC's) for microwave amplifier traveling-wave tubes for space communication and aircraft applications is provided. To attain the highest possible MDC efficiencies, the electrode surfaces must have low secondary electron emission characteristics. Pyrolytic graphite, a chemically vapor-deposited material, is a particularly promising candidate for this application. The pyrolytic graphite surfaces studied were tested over a range of primary electron beam energies and beam impingement angles from 200 to 2000 eV and direct (0 deg) to near-grazing angles (85 deg), respectively. Surfaces both parallel to and normal to the planes of material deposition were examined. The true secondary electron emission and reflected primary electron yield characteristics of the pyrolytic graphite surfaces are compared to those of sooted control surfaces.

Curren, A. N.↗

NASA NTRS1983

Boundary layers in cataclysmic variables: The HEAO-1 X-ray constraints

Jensen, K. A.↗

NASA NTRS1983

The correlated X-ray and optical time variability of TT Arietis

The results of Einstein X-ray observation and simultaneous optical observations of the cataclysmic variable TT Arietis extending over several binary orbits are reported. Evidence is found for correlations between the X-ray and optical variability of TT Ari on three distinct time scales: the 3.3 hour variability that has been associated with the orbital period of the star, the about 1000 s time scale of the irregular flickering activity, and the time scale of quasi-coherent oscillations which have periods of order 10 s. There is a modulation of the X-ray flux with a period consistent with the orbital period of approximately 200 minutes, but there is no apparent modulation of the X-ray spectrum. The optical flux is modulated with a similar period and may lag the X-ray modulation by about 0.1 in phase. The X-ray spectrum is well fitted by a thermal bremsstrahlung plus Gaunt factor model. The results suggest that the hard X-ray emission may be produced in a corona above and below the inner accretion disk.

Jensen, K. A.↗

NASA NTRS1983

Optical identification of the X-ray source E1405-451 - A 101.5 minute binary system with extremely rapid quasi-periodic variability

Explore the source record for details and available documents.

Mason, K. O.↗

NASA NTRS1983

HEAO A-2 soft X-ray source catalog

The HEAO A-2 low energy X-ray detectors have surveyed over 95% of the sky in the spectral bands 0.18-0.44 and 0.44-2.8 keV, down to a typical limiting sensitivity of 1 x 10 to the -11th and 3 x 10 to the -11th ergs per sq cm per sec in each band, respectively. Using a significance criterion of 6 sigma for existence, 114 sources are cataloged, of which 54 were previously undiscovered and 32 remain unidentified. The catalog contains a listing of all counterpart identifications and a cross-reference to all HEAO 1 A-2 low energy detector team publications on the catalog sources complete through the end of 1981. Supplementary material allows the estimation of spectral parameters for the spectral models from the observed intensities. Simple graphs allow the extraction of energy fluxes at the earth, both with and without the effects of interstellar absorption. The angular distribution of the cataloged sources in the 0.44-2.8 keV band is concentrated toward the galactic plane and resembles that seen at higher energy. The distribution in the 0.18-0.44 keV band is more uniform and contains many more newly discovered and unidentified sources.

Nugent, J. J.↗

NASA NTRS1982

H1409-45 - A recurrent soft X-ray transient

Satellite observations of the soft X-ray variable H1409-45 and observations of a promising optical counterpart are reviewed. It is shown that the source appears to have several types of X-ray variability, ranging from rapid flickering on time scales of seconds to changes between states of different intrinsic luminosity on time scales of months to years, and that the source's X-ray spectrum appears to be softer in its high-luminosity state. The observations indicate that H1409-45 may be a white dwarf accreting mass from a close binary companion and that the X-ray and optical properties most closely resemble the AM Her variables.

Jensen, K. A.↗

NASA NTRS1981

The HEAO-1 soft X-ray survey of cataclysmic variable stars

A survey of the soft X-ray emission from 206 cataclysmic variable stars, including dwarf novae in optically quiescent states, classical novae, recurrent novae, nova-like objects and polars, is reported. This is an extension of a previous survey of dwarf novae in outbursts by Cordova et al. (1980). The number of surveyed stars that correspond to features greater than 2 sigma is not in excess of the number of chance coincidences expected on the basis of a random sample of positions distributed over the entire sky. While a few cataclysmic variables have been previously identified as X-ray sources, the results of this survey imply that cataclysmic variables as a class must be, at best, low-luminosity X-ray sources with fluxes below the HEAO-1 A2 detector's sensitivity limit of a few times 10 to the -11th erg/sq cm-s in the energy range 0.1-3 keV. The X-ray luminosities of the cataclysmic variables are consistent with predictions from disk accretion models, provided that a wide range of accretion rates apply.

Cordova, F. A.↗

NASA NTRS1972

Amplifier for signal from thin film transducer

Electronic circuitry is devised to raise low level signal from platinum film type transducer to sufficient amplitude to trigger oscilloscope or time interval counter. Circuit can be used wherever it is necessary to raise level of low amplitude, low impedance positive polarity pulse source to a 5 or 6 volt level.

Jensen, K. A.↗