Search NASA⌕ Search

Engineering topics

Jeon, Hyeongtag

Publications and source records attributed to Jeon, Hyeongtag.

Erratum: “History of atomic layer deposition and its relationship with the American Vacuum Society” [J. Vac. Sci. Technol. A 31, 050818 (2013)]

The authors of this review article published in 20131 would like to correct some text and references relating to the first observations and publications on molecular layering. In Sec. II, “Early Years of Atomic Layer Processes” in the original article,1 the first two sentences of the fourth paragraph should instead say “The ALD principle, where surface reactions follow a binary sequence of self-limiting half-reactions, was reported under the name ‘molecular layering’ in the 1960s by S. I. Kol’tsov from Leningrad Technological Institute.2–6 These experiments were conducted under the scientific supervision of V. B. Aleskovskii. The ‘framework hypothesis,’ an antecedent to molecular layering, was proposed by V. B. Aleskovskii in 1952.6” In addition, again in this same section and paragraph, the last two sentences should instead say “In the 1969 article,3 the authors report that the initial reaction between TiCl4 and Si–OH tends to involve 3 Si–OH, forming one Ti–Cl, whereas after the first water step, the second TiCl4 exposure reacts with 2 Ti–OH, forming Ti–Cl2 groups. In the 1969 paper,3 a planar thin film was not produced or evaluated, although nanolayers were prepared by molecular layering at that time.6” These corrections do not affect other sections or the conclusions drawn in the article.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Terahertz rectification in ring-shaped quantum barriers

Tunneling is the most fundamental quantum mechanical phenomenon with wide-ranging applications. Matter waves such as electrons in solids can tunnel through a one-dimensional potential barrier, e.g. an insulating layer sandwiched between conductors. A general approach to control tunneling currents is to apply voltage across the barrier. Here, we form closed loops of tunneling barriers exposed to external optical control to manipulate ultrafast tunneling electrons. Eddy currents induced by incoming electromagnetic pulses project upon the ring, spatiotemporally changing the local potential. The total tunneling current which is determined by the sum of contributions from all the parts along the perimeter is critically dependent upon the symmetry of the loop and the polarization of the incident fields, enabling full-wave rectification of terahertz pulses. By introducing global geometry and local operation to current-driven circuitry, our work provides a novel platform for ultrafast optoelectronics, macroscopic quantum phenomena, energy harvesting, and multi-functional quantum devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Improvement of the thermal stability of nickel silicide using a ruthenium interlayer deposited via remote plasma atomic layer deposition

In this study, the effects of a thin Ru interlayer on the thermal and morphological stability of NiSi have been investigated. Ru and Ni thin films were deposited sequentially to form a Ni/Ru/Si bilayered structure, without breaking the vacuum, by remote plasma atomic layer deposition (RPALD) on a p-type Si wafer. After annealing at various temperatures, the thermal stabilities of the Ni/Ru/Si and Ni/Si structures were investigated by various analysis techniques. The results showed that the sheet resistance of the Ni/Ru/Si sample was consistently lower compared to the Ni/Si sample over the entire temperature range. Although both samples exhibited the formation of NiSi{sub 2} phases at an annealing temperature of 800 °C, as seen with glancing angle x-ray diffraction, the peaks of the Ni/Ru/Si sample were observed to have much weaker intensities than those obtained for the Ni/Si sample. Moreover, the NiSi film with a Ru interlayer exhibited a better interface and improved surface morphologies compared to the NiSi film without a Ru interlayer. These results show that the phase transformation of NiSi to NiSi{sub 2} was retarded and that the smooth NiSi/Si interface was retained due to the activation energy increment for NiSi{sub 2} nucleation that is caused by adding a Ru interlayer. Hence, it can be said that the Ru interlayer deposited by RPALD can be used to control the phase transformation and physical properties of nickel silicide phases.

36 MATERIALS SCIENCE↗

Fast spatial atomic layer deposition of Al{sub 2}O{sub 3} at low temperature (<100 °C) as a gas permeation barrier for flexible organic light-emitting diode displays

The authors developed a high throughput (70 Å/min) and scalable space-divided atomic layer deposition (ALD) system for thin film encapsulation (TFE) of flexible organic light-emitting diode (OLED) displays at low temperatures (<100 °C). In this paper, the authors report the excellent moisture barrier properties of Al{sub 2}O{sub 3} films deposited on 2G glass substrates of an industrially relevant size (370 × 470 mm{sup 2}) using the newly developed ALD system. This new ALD system reduced the ALD cycle time to less than 1 s. A growth rate of 0.9 Å/cycle was achieved using trimethylaluminum as an Al source and O{sub 3} as an O reactant. The morphological features and step coverage of the Al{sub 2}O{sub 3} films were investigated using field emission scanning electron microscopy. The chemical composition was analyzed using Auger electron spectroscopy. These deposited Al{sub 2}O{sub 3} films demonstrated a good optical transmittance higher than 95% in the visible region based on the ultraviolet visible spectrometer measurements. Water vapor transmission rate lower than the detection limit of the MOCON test (less than 3.0 × 10{sup −3} g/m{sup 2} day) were obtained for the flexible substrates. Based on these results, Al{sub 2}O{sub 3} deposited using our new high-throughput and scalable spatial ALD is considered a good candidate for preparation of TFE films of flexible OLEDs.

36 MATERIALS SCIENCE↗

Characteristics of WN{sub x}C{sub y} films deposited using remote plasma atomic layer deposition with ({sup Me}Cp)W(CO){sub 2}(NO) for Cu diffusion barrier

Diffusion barrier characteristics of tungsten–nitride–carbide (WN{sub x}C{sub y}) thin films interposed between Cu and SiO{sub 2} layers were studied. The WN{sub x}C{sub y} films were deposited by remote plasma atomic layer deposition (RPALD) using a metal organic source, ({sup Me}Cp)W(CO){sub 2}(NO), and ammonia. Auger electron spectroscopy analysis indicated the WN{sub x}C{sub y} films consisted of tungsten, nitrogen, carbon, and oxygen. X-ray diffraction (XRD) analysis showed that the film deposited at 350 °C was nanocrystalline. The resistivity of WN{sub x}C{sub y} film deposited by RPALD was very low compared to that in previous research because of the lower nitrogen content and different crystal structures of the WN{sub x}C{sub y}. To verify the diffusion barrier characteristics of the WN{sub x}C{sub y} film, Cu films were deposited by physical vapor deposition after WN{sub x}C{sub y} film was formed by RPALD on Si substrate. The Cu/WN{sub x}C{sub y}/Si film stack was annealed in a vacuum by rapid thermal annealing at 500 °C. Cu diffusion through the barrier layer was verified by XRD. Stable film properties were observed up to 500 °C, confirming that WN{sub x}C{sub y} film is suitable as a Cu diffusion barrier in microelectronic circuits.

36 MATERIALS SCIENCE↗

Epitaxial Growth of Three-Dimensionally Mesostructured Single-Crystalline Cu 2 O via Templated Electrodeposition

Significant efforts have been made over the past few decades to realize functional three-dimensional photonic crystal devices including zero-threshold lasers, waveguides, light-emitting diodes (LEDs), and solar cells; however, progress has been limited because of difficulties in creating three-dimensional photonic crystals from single-crystal materials. Most have been formed from polycrystalline materials and thus have generally exhibited poor electronic properties. Realization of materials containing complex three-dimensional mesostructures, in single-crystal form, remains a significant challenge. Furthermore, we demonstrate the epitaxial growth of three-dimensionally mesostructured Cu 2 O by bottom-up electrodeposition through a 3D silica colloidal template. Not only is the templated Cu 2 O single crystal, but when the electrodeposition continues past the colloidal template, the crystallinity of the overlying solid Cu 2 O appears to be improved because the template blocks threading dislocations, resulting in substantial reductions in the dislocation density of the overlying solid Cu 2 O.

36 MATERIALS SCIENCE↗

Resistive switching of a TaO{sub x}/TaON double layer via ionic control of carrier tunneling

Resistance random access memory (RRAM) is an attractive candidate for future non-volatile memory due to its superior features. As the oxide thickness is scaled down, the charge transport mechanism is also subject to the transition from hopping to tunneling dominant process, which is critically related to the interfacial electronic band structure. A TaO{sub x}/TaON double layer-based RRAM is fabricated and characterized in this work. Upon TaON insertion at the lower interface, the improved switching behavior is observed. The TaON at the bottom electrode interface blocks oxygen vacancy percolation due to strong N-O bonds and also modifies interfacial band alignment to lower the injected electron energy from bottom electrode due to higher tunneling barrier height than that of TaO{sub x}/Pt. This study suggested that a defect-minimized insertion layer like TaON with a proper interfacial band alignment is pivotal in RRAM for the effective ionic control of carrier tunneling resulting in non-linear I-V behavior with improved properties.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Al{sub 2}O{sub 3} multi-density layer structure as a moisture permeation barrier deposited by radio frequency remote plasma atomic layer deposition

Al{sub 2}O{sub 3} films deposited by remote plasma atomic layer deposition have been used for thin film encapsulation of organic light emitting diode. In this study, a multi-density layer structure consisting of two Al{sub 2}O{sub 3} layers with different densities are deposited with different deposition conditions of O{sub 2} plasma reactant time. This structure improves moisture permeation barrier characteristics, as confirmed by a water vapor transmission rate (WVTR) test. The lowest WVTR of the multi-density layer structure was 4.7 × 10{sup −5} gm{sup −2} day{sup −1}, which is one order of magnitude less than WVTR for the reference single-density Al{sub 2}O{sub 3} layer. This improvement is attributed to the location mismatch of paths for atmospheric gases, such as O{sub 2} and H{sub 2}O, in the film due to different densities in the layers. This mechanism is analyzed by high resolution transmission electron microscopy, elastic recoil detection, and angle resolved X-ray photoelectron spectroscopy. These results confirmed that the multi-density layer structure exhibits very good characteristics as an encapsulation layer via location mismatch of paths for H{sub 2}O and O{sub 2} between the two layers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Significant electrical control of amorphous oxide thin film transistors by an ultrathin Ti surface polarity modifier

We demonstrate an enhanced electrical stability through a Ti oxide (TiO{sub x}) layer on the amorphous InGaZnO (a-IGZO) back-channel; this layer acts as a surface polarity modifier. Ultrathin Ti deposited on the a-IGZO existed as a TiO{sub x} thin film, resulting in oxygen cross-binding with a-IGZO surface. The electrical properties of a-IGZO thin film transistors (TFTs) with TiO{sub x} depend on the surface polarity change and electronic band structure evolution. This result indicates that TiO{sub x} on the back-channel serves as not only a passivation layer protecting the channel from ambient molecules or process variables but also a control layer of TFT device parameters.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Radio frequency plasma power dependence of the moisture permeation barrier characteristics of Al{sub 2}O{sub 3} films deposited by remote plasma atomic layer deposition

In the present study, we investigated the gas and moisture permeation barrier properties of Al{sub 2}O{sub 3} films deposited on polyethersulfone films (PES) by capacitively coupled plasma (CCP) type Remote Plasma Atomic Layer Deposition (RPALD) at Radio Frequency (RF) plasma powers ranging from 100 W to 400 W in 100 W increments using Trimethylaluminum [TMA, Al(CH{sub 3}){sub 3}] as the Al source and O{sub 2} plasma as the reactant. To study the gas and moisture permeation barrier properties of 100-nm-thick Al{sub 2}O{sub 3} at various plasma powers, the Water Vapor Transmission Rate (WVTR) was measured using an electrical Ca degradation test. WVTR decreased as plasma power increased with WVTR values for 400 W and 100 W of 2.6 × 10{sup −4} gm{sup −2}day{sup −1} and 1.2 × 10{sup −3} gm{sup −2}day{sup −1}, respectively. The trends for life time, Al-O and O-H bond, density, and stoichiometry were similar to that of WVTR with improvement associated with increasing plasma power. Further, among plasma power ranging from 100 W to 400 W, the highest power of 400 W resulted in the best moisture permeation barrier properties. This result was attributed to differences in volume and amount of ion and radical fluxes, to join the ALD process, generated by O{sub 2} plasma as the plasma power changed during ALD process, which was determined using a plasma diagnosis technique called the Floating Harmonic Method (FHM). Plasma diagnosis by FHM revealed an increase in ion flux with increasing plasma power. With respect to the ALD process, our results indicated that higher plasma power generated increased ion and radical flux compared with lower plasma power. Thus, a higher plasma power provides the best gas and moisture permeation barrier properties.

36 MATERIALS SCIENCE↗

Charge trapping characteristics of Au nanocrystals embedded in remote plasma atomic layer-deposited Al{sub 2}O{sub 3} film as the tunnel and blocking oxides for nonvolatile memory applications

Remote plasma atomic layer deposited (RPALD) Al{sub 2}O{sub 3} films were investigated to apply as tunnel and blocking layers in the metal-oxide-semiconductor capacitor memory utilizing Au nanocrystals (NCs) for nonvolatile memory applications. The interface stability of an Al{sub 2}O{sub 3} film deposited by RPALD was studied to observe the effects of remote plasma on the interface. The interface formed during RPALD process has high oxidation states such as Si{sup +3} and Si{sup +4}, indicating that RPALD process can grow more stable interface which has a small amount of fixed oxide trap charge. The significant memory characteristics were also observed in this memory device through the electrical measurement. The memory device exhibited a relatively large memory window of 5.6 V under a 10/-10 V program/erase voltage and also showed the relatively fast programming/erasing speed and a competitive retention characteristic after 10{sup 4} s. These results indicate that Al{sub 2}O{sub 3} films deposited via RPALD can be applied as the tunnel and blocking oxides for next-generation flash memory devices.

36 MATERIALS SCIENCE↗

Effects of Ar plasma treatment for deposition of ruthenium film by remote plasma atomic layer deposition

Ruthenium thin films were deposited on argon plasma-treated SiO{sub 2} and untreated SiO{sub 2} substrates by remote plasma atomic layer deposition using bis(ethylcyclopentadienyl)ruthenium [Ru(EtCp){sub 2}] as a Ru precursor and ammonia plasma as a reactant. The results of in situ Auger electron spectroscopy (AES) analysis indicate that the initial transient region of Ru deposition was decreased by Ar plasma treatment at 400 deg. C, but did not change significantly at 300 deg. C The deposition rate exhibited linearity after continuous film formation and the deposition rates were about 1.7 A/cycle and 0.4 A/cycle at 400 deg. C and 300 deg. C, respectively. Changes of surface energy and polar and dispersive components were measured by the sessile drop test. The quantity of surface amine groups was measured from the surface nitrogen concentration with AES. Furthermore, the Ar plasma-treated SiO{sub 2} contained more amine groups and less hydroxyl groups on the surface than on untreated SiO{sub 2}. Auger spectra exhibited chemical shifts by Ru-O bonding, and larger shifts were observed on untreated substrates due to the strong adhesion of Ru films.

36 MATERIALS SCIENCE↗

Investigation of the surface chemical and electronic states of pyridine-capped CdSe nanocrystal films after plasma treatments using H{sub 2}, O{sub 2}, and Ar gases

Surface chemical bonding and the electronic states of pyridine-capped CdSe nanocrystal films were evaluated using x-ray photoelectron spectroscopy and ultraviolet photoelectron spectroscopy before and after plasma treatments using H{sub 2}, O{sub 2}, and Ar gases from the viewpoint of studying the effects of surface capping organic molecules and surface oxidation. Surface capping organic molecules could be removed during the plasma treatment due to the chemical reactivity, ion energy transfer, and vacuum UV (VUV) of the plasma gases. With O{sub 2} plasma treatment, surface capping organic molecules were effectively removed but substantial oxidation of CdSe occurred during the plasma treatment. The valence band maximum energy (E{sub VBM}) of CdSe nanocrystal films mainly depends on the apparent size of pyridine-capped CdSe nanocrystals, which controls the interparticle distance, and also on the oxidation of CdSe nanocrystals. Cd-rich surface in O{sub 2} and H{sub 2} plasma treatments partially would compensate for the decrease in E{sub VBM}. After Ar plasma treatment, the smallest value of E{sub VBM} resulted from high VUV photon flux, short wavelength, and ion energy transfer. The surface bonding states of CdSe had a strong influence on the electronic structure with the efficient strip of capping molecules as well as different surface oxidations and surface capping molecule contents.

36 MATERIALS SCIENCE↗

The reaction pathways of the oxygen plasma pulse in the hafnium oxide atomic layer deposition process

The plasma enhanced atomic layer deposition process for the HfO{sub 2} thin film is modeled as simple reactions between Hf(OH){sub 3}NH{sub 2} and reactive oxygen species. The density functional theory calculation was performed for plausible reaction pathways to construct the reaction profile. While the triplet molecular oxygen is unlikely to form a reactive complex, the singlet molecular oxygen forms the stable adduct that goes through the transition state and completes the reaction pathway to the products. Either two singlet or two triplet oxygen atoms make the singlet adduct complex, which follows the same pathway to the product as the singlet molecular oxygen reacts.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗