Non-linear MHD Modelling of ELM Triggering by Pellet Injection in DIII-D and implications for ITER
Abstract not provided
Engineering topics
Publications and source records attributed to Jernigan, T C.
Abstract not provided
Recent experiments in the DIII-D tokamak have demonstrated real-time control and dissipation of post-disruption runaway electron (RE) beams. In the event that disruption avoidance, control, and mitigation schemes fail to avoid or suppress RE generation, active control of the RE beam may be an important line of defense to prevent the rapid, localized deposition of RE beam energy onto vulnerable vessel sections. During and immediately after the current quench, excessive radial compression of the runaway beams is avoided by a combination of techniques, improving the likelihood of the beams surviving this dynamic period without a fast termination. Once stabilized, the runaway beams are held in a steady state (out to the ohmic flux limit) with the application of active plasma current and position controls. Beam interaction with the vessel wall is minimized by avoiding distinct thresholds for enhanced wall interaction at small and large radii, corresponding to inner wall and outer limiter interaction, respectively. Staying within the 'safe zone' between those radial thresholds allows for the sustainment of long-lived, quiescent runaway beams. The total beam energy and runaway electron population are then dissipated gradually by a controlled ramp-down of the runaway current.
The spatial distribution of runaway electron (RE) strikes to the wall during argon pellet-initiated rapid shutdown of diverted and limited plasma shapes in DIII-D is studied using a new array of hard x-ray (HXR) scintillators. Two plasma configurations were investigated: an elongated diverted H-mode and a low-elongation limited L-mode. HXR emission from MeV level REs generated during the argon pellet injection is observed during the thermal quench (TQ) in diverted discharges from REs lost into the divertor. In limiter discharges, this prompt TQ loss is reduced, suggesting improved TQ confinement of REs in this configuration. During the plateau phase when the plasma current is carried by REs, toroidally symmetric HXR emission from remaining confined REs is seen. Transient HXR bursts during this RE current plateau suggest the presence of a small level of wall losses due to the presence of an unidentified instability. Eventually, an abrupt final loss of the remaining RE current occurs. This final loss HXR emission shows a strong toroidal peaking and a consistent spatiotemporal evolution that suggests the development of a kink instability.
Large relativistic runaway electron currents (0.1-0.5 MA) persisting for similar to 100 ms are created in the DIII-D tokamak during rapid discharge shut down caused by argon pellet injection. Slow upward and downward ramps in runaway currents were found in response to externally applied loop voltages. Comparison between the observed current growth/decay rate and the rate expected from the knock-on avalanche mechanism suggests that classical collisional dissipation of runaways alone cannot account for the measured growth/damping rates. It appears that a fairly constant anomalous dissipation rate of order 10 s(-1) exists, possibly stemming from radial transport or direct orbit losses to the vessel walls, although the possibility of an apparent loss due to current profile shrinking cannot be ruled out at present.
We describe results from recent experiments studying interaction of solid polystyrene pellets with a runaway electron current channel generated after cryogenic argon pellet rapid shutdown of DIII-D. Fast camera imaging shows the pellet trajectory and continuum emission from the subsequent explosion, with geometric calibration providing detailed explosion analysis and runaway energy. Electron cyclotron emission also occurs, associated with knock-on electrons broken free from the pellet by RE which then accelerate and runaway, and also with a short lived hot plasma blown off the pellet surface. In addition, we compare heating and explosion times from observations and a model of pellet heating and breakdown by runaway interaction. (C) 2011 Elsevier B.V. All rights reserved
Experiments have been performed in the DIII-D tokamak [J. L. Luxon, Nucl. Fusion 42, 614 (2002)] toward understanding runaway electron formation and amplification during rapid discharge shutdown, as well as toward achieving complete collisional suppression of these runaway electrons via massive delivery of impurities. Runaway acceleration and amplification appear to be well explained using the zero-dimensional (0D) current quench toroidal electric field. 0D or even one-dimensional modeling using a Dreicer seed term, however, appears to be too small to explain the initial runaway seed formation. Up to 15% of the line-average electron density required for complete runaway suppression has been achieved in the middle of the current quench using optimized massive gas injection with multiple small gas valves firing simultaneously. The novel rapid shutdown techniques of massive shattered pellet injection and shell pellet injection have been demonstrated for the first time. Experiments using external magnetic perturbations to deconfine runaways have shown promising preliminary results.
Pellet injection is planned to be the main fuelling method on ITER. The high temperature of the plasma during a fusion burn will limit the penetration of the pellet to the outer third of the minor radius. This limited penetration is expected to be compensated by a polarization drift, which will deposit the particles deeper in the plasma for the pellets injected from the high field side. In order to evaluate the expected depth of the fuelling on ITER, a good understanding of this drift effect is important. Experimental data acquired on the DIII-D (USA) and Tore Supra (France) tokamaks show that the polarization drift is influenced by the low order rational q surfaces. These surfaces appear to attenuate the polarization mechanism as the drifting particles cross them. In this paper, a correlation between the maximum of the pellet mass deposition profile and the positions of the q = 2 and q = 3 surfaces on DIII-D and Tore Supra is shown for high field side and low field side injection. A model is proposed to explain this effect and compared with the experimental results. To conclude, the possible consequences of this phenomenon on the fuelling in ITER are described.
On DIII-D, the H-mode power threshold has been determined for hydrogen, deuterium and helium plasmas heated by neutral beam injection and/or by electron cyclotron heating and as a function of the applied torque plasmas for plasma configurations in the favourable ion grad-B drift direction. The H-mode threshold power has been determined to increase with input torque for all the main ion species (hydrogen, deuterium and helium). The H-mode threshold power for similar plasma parameters and configurations is the least for deuterium, followed by helium and hydrogen in that order. The plasma geometry also affects the power threshold, which is dependent on the X-point height.
Small (o.d. = 1.8 mm, t = 0.37 mm) polystyrene shells filled with either pressurized argon gas or boron powder have been fired into DIII-D plasmas for disruption mitigation experiments. The pellet shells were observed to burn up at rhoapprox =0.5, roughly consistent with ablation rate calculations. Pellet slowing from 350 m/s down to 100 m/s was observed, which is not well-understood at present. Negligible plasma current contraction or MHD onset were seen as a result of the shell burn-up in the plasma edge, consistent with calculations. The pellet payloads were observed to ionize rapidly in the pellet vicinity (<1 cm radius) and rapid (<15 ms) mixing through the plasma core was observed.