Search NASA⌕ Search

Engineering topics

Jernigan, Thomas C

Publications and source records attributed to Jernigan, Thomas C.

Reduction of edge localized mode intensity on DIII-D by on-demand triggering with high frequency pellet injection and implications for ITER

The injection of small deuterium pellets at high repetition rates up to 12× the natural edge localized mode (ELM) frequency has been used to trigger high-frequency ELMs in otherwise low natural ELM frequency H-mode deuterium discharges in the DIII-D tokamak [J. L. Luxon and L. G. Davis, Fusion Technol. 8, 441 (1985)]. The resulting pellet-triggered ELMs result in up to 12× lower energy and particle fluxes to the divertor than the natural ELMs. The plasma global energy confinement and density are not strongly affected by the pellet perturbations. The plasma core impurity density is strongly reduced with the application of the pellets. These experiments were performed with pellets injected from the low field side pellet in plasmas designed to match the ITER baseline configuration in shape and normalized β operation with input heating power just above the H-mode power threshold. Nonlinear MHD simulations of the injected pellets show that destabilization of ballooning modes by a local pressure perturbation is responsible for the pellet ELM triggering. This strongly reduced ELM intensity shows promise for exploitation in ITER to control ELM size while maintaining high plasma purity and performance.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Characterization of heat loads from mitigated and unmitigated vertical displacement events in DIII-D

Experiments have been conducted on the DIII-D tokamak to study the distribution and repeatability of heat loads and vessel currents resulting from vertical displacement events (VDEs). For unmitigated VDEs, the radiated power fraction appears to be of order 50%, with the remaining power dominantly conducted to the vessel walls. Shot-to-shot scatter in heat loads measured at one toroidal location is not large (<±50%), suggesting that toroidal asymmetries in conducted heat loads are not large. Conducted heat loads are clearly observed during the current quench (CQ) of both mitigated and unmitigated disruptions. Significant poloidal asymmetries in heat loads and radiated power are often observed in the experiments but are not yet understood. Energy dissipated resistively in the conducting walls during the CQ appears to be small (<5%). The mitigating effect of neon massive gas injection (MGI) as a function of MGI trigger delay has also been studied. Improved mitigation is observed as the MGI trigger delay is decreased. For sufficiently early MGI mitigation, close to 100% radiated energy and a reduction of roughly a factor 2 in vessel forces is achieved.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Visible imaging and spectroscopy of disruption runaway electrons in DIII-D

The first visible light images of synchrotron emission from disruption runaway electrons are presented. The forward-detected continuum radiation from runaways is identified as synchrotron emission by comparing two survey spectrometers and two visible fast cameras viewing in opposite toroidal directions. Analysis of the elongation of 2D synchrotron images of oval-shaped runaway beams indicates that the velocity pitch angle v{sub Up-Tack }/v{sub ||} ranges from 0.1 to 0.2 for the detected electrons, with energies above 25 MeV. Analysis of synchrotron intensity from a camera indicates that the tail of the runaway energy distribution reaches energies up to 60 MeV, which agrees with 0D modeling of electron acceleration in the toroidal electric field generated during the current quench. A visible spectrometer provides an independent estimate of the upper limit of runaway electron energy which is roughly consistent with energy determined from camera data. Synchrotron spectra reveal that approximately 1% of the total post-thermal quench plasma current is carried by the detected high-energy runaway population with energies in the range of 25-60 MeV; the bulk of the plasma current thus appears to be carried by relativistic electrons with energy less than 25 MeV. In addition to stable oval shapes, runaway beams with other shapes and internal structure are sometimes observed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experimental Demonstration of High Frequency ELM Pacing by Pellet Injection on DIII-D and Extrapolation to ITER

. The injection of high repetition rate deuterium pellets is shown to trigger high-frequency edge localized modes (ELMs) in otherwise low natural ELM frequency H-mode deuterium discharges in the DIII-D tokamak. The resulting triggered ELMs have significantly lower energy and particle fluxes to the divertor than the natural ELMs. The plasma global energy confinement and density are not strongly affected by the pellet perturbations. The plasma core impurity density is strongly reduced with the application of the pellets. These experiments were performed in plasmas designed to match the ITER baseline configuration in shape and normalized operation with input power just above the H-mode power threshold. This strongly reduced ELM intensity shows promise for exploitation in ITER to control ELM size while maintaining high plasma purity and performance.

Baylor, Larry R↗

Integrated modelling of steady-state scenarios and heating and current drive mixes for ITER

Recent progress on ITER steady-state (SS) scenario modelling by the ITPA-IOS group is reviewed. Code-to-code benchmarks as the IOS group's common activities for the two SS scenarios (weak shear scenario and internal transport barrier scenario) are discussed in terms of transport, kinetic profiles, and heating and current drive (CD) sources using various transport codes. Weak magnetic shear scenarios integrate the plasma core and edge by combining a theory-based transport model (GLF23) with scaled experimental boundary profiles. The edge profiles (at normalized radius rho = 0.8-1.0) are adopted from an edge-localized mode-averaged analysis of a DIII-D ITER demonstration discharge. A fully noninductive SS scenario is achieved with fusion gain Q = 4.3, noninductive fraction f(NI) = 100%, bootstrap current fraction f(BS) = 63% and normalized beta beta(N) = 2.7 at plasma current I(p) = 8MA and toroidal field B(T) = 5.3 T using ITER day-1 heating and CD capability. Substantial uncertainties come from outside the radius of setting the boundary conditions (rho = 0.8). The present simulation assumed that beta(N)(rho) at the top of the pedestal (rho = 0.91) is about 25% above the peeling-ballooning threshold. ITER will have a challenge to achieve the boundary, considering different operating conditions (T(e)/T(i) approximate to 1 and density peaking). Overall, the experimentally scaled edge is an optimistic side of the prediction. A number of SS scenarios with different heating and CD mixes in a wide range of conditions were explored by exploiting the weak-shear steady-state solution procedure with the GLF23 transport model and the scaled experimental edge. The results are also presented in the operation space for DT neutron power versus stationary burn pulse duration with assumed poloidal flux availability at the beginning of stationary burn, indicating that the long pulse operation goal (3000s) at I(p) = 9 MA is possible. Source calculations in these simulations have been revised for electron cyclotron current drive including parallel momentum conservation effects and for neutral beam current drive with finite orbit and magnetic pitch effects.

Murakami, Masanori↗

Effect of Applied Toroidal Electric Field on the Growth/Decay of Plateau-Phase Runaway Electron Currents in DIII-D

Large relativistic runaway electron currents (0.1-0.5 MA) persisting for similar to 100 ms are created in the DIII-D tokamak during rapid discharge shut down caused by argon pellet injection. Slow upward and downward ramps in runaway currents were found in response to externally applied loop voltages. Comparison between the observed current growth/decay rate and the rate expected from the knock-on avalanche mechanism suggests that classical collisional dissipation of runaways alone cannot account for the measured growth/damping rates. It appears that a fairly constant anomalous dissipation rate of order 10 s(-1) exists, possibly stemming from radial transport or direct orbit losses to the vessel walls, although the possibility of an apparent loss due to current profile shrinking cannot be ruled out at present.

Hollmann, E M↗

A Technique for Producing Large Dual-Layer Pellets in Support of Disruption Mitigation Experiments

A special single-shot pellet injection system that produces and accelerates large cryogenic pellets (~16 mm diameter and composed of D2 or Ne) to relatively high speeds (>300 and 600 m/s, respectively) was previously developed at the Oak Ridge National Laboratory. Subsequently, a similar system was installed on DIII-D and used successfully in disruption mitigation experiments. To circumvent some operational issues with injecting the large Ne pellets, a technique has been developed in which a relatively thin layer (0.1 to 1.0 mm) of D2 is frozen on the inner wall of the pipe-gun barrel, followed by filling the core with solid Ne. The technique and the initial laboratory tests are described, as well as the implementation and operational issues for fusion experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Plasma-surface interactions during tokamak disruptions and rapid shutdowns

Recent progress in understanding of disruptions and in developing methods to avoid disruption damage is presented. Nearly complete mitigation of conducted heat loads has been achieved with high-Z gas jet shutdown. The resulting local radiation heat flash melting in the main chamber might be a concern in ITER, especially with beryllium walls. During the current quench, significant vessel forces can occur due to halo currents I-halo; however, these are found to fall reliably below a boundary of (halo current fraction times halo current peaking factor) <0.7 both experimentally and numerically. Numerical simulations indicate that runaway electrons (REs) could cause serious damage to hard-to reach components in ITER, making their suppression a high priority. During the current quench, less than 20% of the density required for collisional suppression of REs appears to have been achieved. Collisional suppression of REs may have been achieved, however, in full-current RE beams with gas injection. (C) 2010 Elsevier B.V. All rights reserved.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Demonstration of rapid shutdown using large shattered deuterium pellet injection in DIII-D

A severe consequence of a disruption on large tokamaks such as ITER could be the generation of multi-megaelectronvolt electron beams that could damage the vacuum vessel and the structures of the machine if they hit the wall unmitigated. The mitigation of runaway electron beams is thus a key requirement for reliable operation of ITER. In order to achieve reliable disruption mitigation, a new fast shutdown technique has been developed: the injection of a large shattered cryogenic pellet in the plasma, which is expected to increase the electron density up to levels where the beam generation processes are mitigated by collisional losses. This technique has been implemented and tested for the first time ever on DIII-D. The first tests show evidence of an almost instantaneous deposition of more than 260 Pa m(3) of deuterium deep in the core. Record local densities during the thermal quench were observed for each injection with a very high reliability. Pellet mass and plasma energy content scans show an improvement of the assimilation of the particles for higher plasma energy and larger pellet mass.

Commaux, Nicolas JC↗

Alternative Techniques for Injecting Massive Quantities of Gas for Plasma Disruption Mitigation

Injection of massive quantities of noble gases or D2 has proven to be effective at mitigating some of the deleterious effects of disruptions in tokamaks. Two alternative methods that might offer some advantages over the present technique for massive gas injection are shattering massive pellets and employing closecoupled rupture disks. Laboratory testing has been carried out to evaluate their feasibility. For the study of massive pellets, a pipe gun pellet injector cooled with a cryogenic refrigerator was fitted with a relatively large barrel (16.5 mm bore), and D2 and Ne pellets were made and were accelerated to speeds of ~600 and 300 m/s, respectively. Based on the successful proof-of-principle testing with the injector and a special double-impact target to shatter pellets, a similar system has been prepared and installed on DIII-D, with preliminary experiments already carried out. To study the applicability of rupture disks for disruption mitigation, a simple test apparatus was assembled in the lab. Commercially available rupture disks of 1 in. nominal diameter were tested at conditions relevant for the application on tokamaks, including tests with Ar and He gases and rupture pressures of ~54 bar. Some technical and practical issues of implementing this technique on a tokamak are discussed.

disruption↗

Disruption Mitigation Technology Concepts and Implications for ITER

Disruptions on ITER present challenges to handle the intense heat flux, the large forces from halo currents, and the potential first wall damage from energetic runaway electrons. Injecting large quantities of material into the plasma during the disruption can reduce the plasma energy and increase its resistivity to mitigate these effects. Assessments of the amount of various mixtures and quantities of material required have been made to provide collision mitigation of runaway electron conversion [1], which is the most difficult challenge. The quantities of material required (~0.5 MPa-m3 for deuterium or helium gas) are large enough to have implications on the design and operation of the vacuum system and tokamak exhaust processing system.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Demonstration of ELM pacing by Pellet Injection on DIII-D and Extrapolation to ITER

Demonstration of ELM pacing by pellet injection on DIII-D and extrapolation to ITER<#_ftn1>* L.R. Baylor1, N. Commaux1, T.C. Jernigan1, P.B. Parks2, T.E. Evans2, T.H. Osborne2, E.J. Strait2, M.E. Fenstermacher3, C.J. Lasnier3, R.A. Moyer4, J.H. Yu4 1Oak Ridge National Laboratory, Oak Ridge, TN, USA 2General Atomics, San Diego, CA, USA 3 Lawrence Livermore National Laboratory, Livermore, CA, USA 4University of California San Diego, La Jolla, CA, USA Deuterium pellet injection has been used in experiments on the DIII-D tokamak to investigate the possibility of triggering small rapid edge localized modes (ELMs) in reactor relevant plasma regimes. ELMs have been observed to be triggered from small 1.8 mm pellets injected from all available locations and under all H-mode operating scenarios in DIII-D. Experimental details have shown that the ELMs are triggered before the pellets reach the top of the H-mode pedestal, implying that very small shallow penetrating pellets are sufficient to trigger ELMs. Fast camera images of the pellet entering the plasma from the low field side show a single plasma filament becoming visible near the pellet cloud and striking the outer vessel wall within 200 ms. Additional ejected filaments are then observed to subsequently reach the wall. The plasma stored energy loss from the pellet triggered ELMs is a function of the elapsed time after a previous ELM. Pellet ELM pacing has been proposed as a method to prevent large ELMs that can damage the ITER plasma facing components [1]. A demonstration of pacing of ELMs on DIII-D was made by injecting slow 14 Hz pellets on the low field side in an ITER shape plasma with low natural ELM frequency and a normalized b of 1.8. The non-pellet discharge natural ELM frequency was ~5 Hz with ELM energy losses up to 85 kJ (>10% of total stored energy) while the case with pellets was able to demonstrate >20 Hz ELMs with an average ELM energy loss less than 22 kJ (<3% of the total). The resulting ELM frequency was larger than the pellet frequency indicating both a direct ELM trigger by each pellet and an indirect effect on the overall pedestal stability to ELMs from the multiple pellets. No increase in density or significant decrease in energy confinement with the pellets was observed. The implications of these results for possible pellet ELM pacing on ITER will be discussed. [1] P.T. Lang et al., Nucl. Fusion 44 (2004) 665.

Baylor, Larry R↗