Engineering topics
Jesick, Mark
Publications and source records attributed to Jesick, Mark.
Maneuver Design Implementation and Verification for the Mars 2020 Mission
No abstract provided
On-Orbit Contingency Plan for the Mars 2020 Mission
NASA’s Mars 2020 mission successfully launched to Mars July 30, 2020. An on-orbit contingency plan was developed to accomplish a controlled re-entry of the spacecraft in the event of a launch vehicle anomaly. The entire launch period was assessed, and satisfactory de-orbit burns were designed for every launch opportunity. An operational implementation was created for rapid adoption if needed, and validated using information from the Gravity Recovery and Climate Experiment (GRACE) satellites. This paper presents the orbit determination models and filter strategies used to conduct the pre-launch analyses, as well as the operational implementation validation methodologies and results.
Maneuver Design Implementation and Verification for the Mars 2020 Mission
On February 18, 2021, the Perseverance rover landed in Jezero Crater on Mars, transported by the Mars 2020 spacecraft on a nearly seven-month journey to the Red Planet. The execution of three propulsive maneuvers during the interplanetary cruise phase was required to remove the launch-injection bias and deliver the spacecraft to the Mars atmospheric entry point. This paper focuses on the maneuver implementation and verification process between the navigation and spacecraft teams. Additionally, this paper discusses the execution error models that were used to determine maneuver performance and delivery accuracy at the atmospheric entry interface point.
Mars 2020 Trajectory Correction Maneuver Design
The Mars 2020 mission launched on 30 July 2020 and arrived at Mars on 18 February 2021. Delivering the mission’s Perseverance rover to Jezero Crater required adjusting the postlaunch trajectory to remove the launch injection bias and to target the atmospheric entry conditions, while also satisfying requirements on the propellant usage and non-nominal impact probability at Mars. The Mars 2020 maneuver design team achieved these goals by designing and executing three propulsive maneuvers in flight. The accurate on-board execution of those maneuvers delivered the spacecraft into the Martian atmosphere in a state that allowed for a successful entry, descent, and landing on the surface. This paper details the maneuver design process and describes the design and execution of the three in-flight propulsive maneuvers.
Mars 2020 Navigation Performance
On February 18, 2021, the Perseverance rover and Ingenuity helicopter demonstration landed at Jezero Crater. The Entry, Descent, and Landing (EDL) architecture, largely the same used to land Curiosity at Gale Crater on August 6, 2012, required high-fidelity flight dynamics simulation with two independent tools to verify performance. The process for creating the EDL simulation using the Dynamics Simulator for Entry, Descent and Surface landing (DSENDS) tool will be discussed, along with its use for for independent verification of the EDL statistical analysis results and reference trajectory simulation. Analysis and usage details both in development and cruise, along with post-landing assessment of the prediction performance of the simulation, will also be discussed.
Mars 2020 Perseverance trajectory reconstruction and performance from launch through landing
The Mars 2020 (M2020) Mission carrying Perseverance, the most advanced rover ever sent to Mars, successfully launched on an Atlas V 541 (AV-088) launch vehicle from the Eastern Test Range (ETR) at Cape Canaveral Air Force Station (CCAFS) in Florida at 11:50:00 UTC (T-Zero time) on July 30, 2020. After some station reconfiguration, carrier/telemetry were locked at both Deep Space Network (DSN) Canberra and Goldstone stations. Perseverance entered the Martian atmosphere at 20:36:50 Spacecraft Event Time (SCET) UTC, and landed inside Jezero Crater at 20:43:49 SCET UTC on February 18, 2021. Confirmation of nominal landing was received at the DSN Goldstone and Madrid tracking stations via the Mars Reconnaissance Orbiter at 20:55:11 Earth Received Time (ERT) UTC. This paper summarizes in detail the actual vs. predicted performance in terms of launch vehicle events, launch vehicle injection performance, actual DSN spacecraft lockup, trajectory correction maneuver performance, Entry, Descent, and Landing events, and overall trajectory and geometric characteristics.
Orbit Determination for the Mars 2020 Mission
NASA’s Mars 2020 Mission successfully executed its Martian entry, descent, and landing sequence on February 18, 2021. Spacecraft navigation guided the spacecraft from its launch injection to entry into the Martian atmosphere; to do so, three trajectory correction maneuvers and two onboard state updates were performed. Navigation was required to provide an entry state with a maximum uncertainty of 2.8 km in position and 2.0 m/sec in velocity (3-σ); the flight performance was approximately 900 m and 66 cm/sec (3-σ). This paper presents the orbit determination models, measurements, filter strategies and performance throughout launch, cruise and Mars approach.
Mars 2020 Perseverance Trajectory Reconstruction and Performance from Launch through Landing
The Mars 2020 (M2020) Mission carrying Perseverance, the most advanced rover ever sent to Mars, successfully launched on an Atlas V 541 (AV-088) launch vehicle from the Eastern Test Range (ETR) at Cape Canaveral Air Force Station (CCAFS) in Florida at 11:50:00 UTC (T-Zero time) on July 30, 2020. After some station reconfiguration, carrier/telemetry were locked at both Deep Space Network (DSN) Canberra and Goldstone stations. Perseverance entered the Martian atmosphere at 20:36:50 Spacecraft Event Time (SCET) UTC, and landed inside Jezero Crater at 20:43:49 SCET UTC on February 18, 2021. Confirmation of nominal landing was received at the DSN Goldstone and Madrid tracking stations via the Mars Reconnaissance Orbiter at 20:55:11 Earth Received Time (ERT) UTC. This paper summarizes in detail the actual vs. predicted performance in terms of launch vehicle events, launch vehicle injection performance, actual DSN spacecraft lockup, trajectory correction maneuver performance, Entry, Descent, and Landing events, and overall trajectory and geometric characteristics.
SmallSat aerocapture to enable a new paradigm of planetay missions
This paper presents a technology development initiative focused on delivering SmallSats to orbit a variety of bodies using aerocapture. Aerocapture uses the drag of a single pass through the atmosphere to capture into orbit instead of relying on large quantities of rocket fuel. Using drag modulation flight control, an aerocapture vehicle adjusts its drag area during atmospheric flight through a single-stage jettison of a drag skirt, allowing it to target a particular science orbit in the presence of atmospheric uncertainties. A team from JPL, NASA Ames, and CU Boulder has worked to address the key challenges and determine the feasibility of an aerocapture system for SmallSats less than 180kg. Key challenges include the ability to accurately target an orbit, stability through atmospheric flight and the jettison event, and aerothermal stresses due to high heat rates.
Mars 2020 Mission Design and Navigation Overview
Following the exceptionally successful Mars Science Laboratory mission which placed the Curiosity rover in the interior of Gale Crater in August 2012, NASA will launch the next rover in the 2020 Earth to Mars opportunity arriving to the Red Planet in February 2021 to explore areas suspected of former habitability and look for evidence of past life. This paper details the mission and navigation requirements set by the Project and how the final mission design and navigation plan satisfies those requirements.
Mars 2020 mission design and navigation overview
Following the exceptionally successful Mars Science Laboratory mission which placed the Curiosity rover in the interior of Gale Crater in August 2012, NASA will launch the next rover in the 2020 Earth to Mars opportunity arriving to the Red Planet in February 2021 to explore areas suspected of former habitability and look for evidence of past life. This paper details the mission and navigation requirements set by the Project and how the final mission design and navigation plan satisfies those requirements.
Preliminary Interplanetary Mission Design and Navigation for the Dragonfly New Frontiers Mission Concept
Dragonfly is one of two mission concepts selected in December 2017 to advance into Phase A of NASA’s New Frontiers competition. Dragonfly would address the Ocean Worlds mission theme by investigating Titan’s habitability and prebiotic chemistry and searching for evidence of chemical biosignatures of past (or extant) life. A rotorcraft lander, Dragonfly would capitalize on Titan’s dense atmosphere to enable mobility and sample materials from a variety of geologic settings. This paper describes Dragonfly’s baseline mission design giving a complete picture of the inherent tradespace and outlines the design process from launch to atmospheric entry.
Low Excess Speed Triple Cyclers of Venus, Earth, and Mars
Ballistic cycler trajectories which repeatedly encounter Earth and Mars may be invaluable to a future transportation architecture ferrying humans to and from Mars. Such trajectories which also involve at least one flyby of Venus are computed here for the first time. The so-called triple cyclers are constructed to exhibit low excess speed on Earth-Mars transit legs, and thereby reduce the cost of hyperbolic rendezvous. Numerous solutions are identified with average transit leg excess speed below 5 kilometers per second, independent of encounter epoch. The energy characteristics are lower than previously documented cyclers not involving Venus, but the repeat periods are generally longer.