Search NASA⌕ Search

Engineering topics

Jiang, Xiaohua

Publications and source records attributed to Jiang, Xiaohua.

6 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Nanocrystalline strain glass TiNiPt and its superelastic behavior

TiNi-based shape-memory alloys are known to exhibit a strain glass state under certain conditions, generally in the presence of high-density defects such as excess solute atoms or alloying elements, dislocations, and nanoprecipitates. In this paper, we report a strain glass transition in a nanocrystalline Ti 50 Ni 35 Pt 15 alloy. The nanocrystalline strain glass state is achieved by a combined effect of high-density grain boundaries and high concentration doping of Pt atoms in the B2 matrix. The nanocrystalline Ti 50 Ni 35 Pt 15 strain glass alloy showed a large near-complete progressive superelasticity with a recovery strain of about 6% and a low apparent Young's modulus of about 30 GPa in a wide temperature range of over 200 °C. In situ synchrotron x-ray diffraction measurement showed that the strain glass B2 [B2(SG)] phase experienced B2(SG)→R→B19 transformation upon loading and B19→B2(SG) upon unloading. The findings of this study provide insight for the development of nanocrystalline strain glass shape-memory alloys.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

High performance Nb/TiNi nanocomposites produced by packaged accumulative roll bonding

Taking full advantage of intrinsic high strength of nano-reinforcements has been proven difficult in a composite until the concept of strain matching was experimental verified in a nanowire Nb/TiNi in-situ composite, which was obtained via solidifying eutectic Nb/TiNi and subsequent severe wire drawing. However, the volume fraction of the nano-reinforcement was dictated by eutectic reaction, which severely limited the development of high-performance composites. Here, the martensitic transformation nanocomposites were successfully acquired with increased volume fraction and changeable morphology of the nano-reinforcement through hot packaged ARB (PARB) and subsequent wire drawing. The nano-reinforcement with lamellar configuration in the composite could exhibit a large lattice strain of similar to 3.8%, which demonstrated the applicability and effectiveness of the strain matching principle in nano-lamellar composite. The obtained composites show a yield strength over 2.0 GPa and a quasi-linear elastic strain as larger as similar to 6.5% with adjustable apparent elastic modulus from 30 to 50 GPa.

42 ENGINEERING↗
DOE OSTI2020

Design Optimization of Medium-Frequency Transformer for DAB Converters With DC Bias Capacity

Medium-frequency transformer (MFT) dc bias is critical for the safe operation of dual-active-bridge (DAB) converters. To analyze the dc bias, expressions of dc bias are derived for SiC MOSFET DAB converters. It shows that the dc bias is a current source in steady state; thus, a dc bias current capacity is defined and used as a design constraint in the optimization of MFT. The dc bias current capacity is related to core materials, geometric parameters, and flux density, which is analyzed with analytical expression. Optimization equations with geometric variables are derived, which can be solved theoretically or numerically for both interleaved winding (IW) and separated winding (SW) MFT without and/or with leakage inductance design. Based on the optimization equations, different MFT designs for a 150-kW SiC MOSFET DAB converter are compared on the aspects of core materials, winding structures, and without/with leakage inductance design. The combination of IW structure MFT with auxiliary phase shift inductors is chosen, and the assembled prototype is tested with the 150-kW DAB converter. Here, the designed dc bias capacity, temperature rise, and efficiency are verified.

42 ENGINEERING↗
DOE OSTI2020

Large elastic strains and ductile necking of W nanowires embedded in TiNi matrix

The deformation behaviors of W nanowires embedded in a TiNi matrix were investigated by means of in-situ synchrotron high energy X-ray diffraction (HEXRD) and in-situ transmission electron microscopy (TEM) analysis during tensile deformation. The HEXRD measurement indicated that the W nanowires exhibited an average lattice strain of about 1.50 %, whereas the TEM examination revealed a local elastic strain of about 4.59 % in areas adjacent to the TiNi matrix where stress-induced martensitic transformation occurred. This strain corresponds to a stress of ~15 GPa for the W nanowires. In addition, in areas adjacent to the TiNi matrix where plastic deformation and cracking were generated, the W nanowire showed significant ductile necking with ~80 % reduction in cross-section area. In conclusion, the ductile necking of W nanowire is attributed to the lack of protection from the stress-induced martensitic transformation of the TiNi matrix.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Flux Balancing Control of Ungapped Nanocrystalline Core-Based Transformer in Dual Active Bridge Converters

Transformer flux dc bias is a critical issue, impacting the reliable operation of dual active bridge (DAB) converters especially when ungapped high permeability nanocrystalline core is used. Steady state current dc bias can easily saturate ungapped nanocrystalline transformers, and it is even more dangerous in transient conditions. A dc bias model is proposed to analyze steady state dc bias in different load conditions. The magnetizing current detection is necessary for closed-loop control of dc bias; conductors' position is shown to impact sensor noise, and it is analyzed in detail. To deal with both steady state and transient dc bias, a unified flux balancing control (UFBC) is proposed introducing a predictive bias suppression (PBS) method with closed-loop flux balancing control (CFBC). With the proposed PBS, both primary/secondary current balance and flux balance can be achieved within one switching cycle using UFBC. Power characteristics and interaction between power control and flux balancing control of DAB converters are analyzed, and the CFBC needs to work in a low bandwidth due to sensor bandwidth limitation and interaction between power control and flux balancing control. Lastly, the UFBC is verified on a 300-kW cascaded DAB converter prototype.

42 ENGINEERING↗