Engineering topics

Jiang, Xiaoyu

Publications and source records attributed to Jiang, Xiaoyu.

3 records

DOE OSTI2024

The FBXW7-binding sites on FAM83D are potential targets for cancer therapy

Increasing evidence shows the oncogenic function of FAM83D in human cancer, but how FAM83D exerts its oncogenic function remains largely unclear. Here, we investigated the importance of FAM83D/FBXW7 interaction in breast cancer (BC). We systematically mapped the FBXW7-binding sites on FAM83D through a comprehensive mutational analysis together with co-immunoprecipitation assay. Mutations at the FBXW7-binding sites on FAM83D led to that FAM83D lost its capability to promote the ubiquitination and proteasomal degradation of FBXW7; cell proliferation, migration, and invasion in vitro; and tumor growth and metastasis in vivo, indicating that the FBXW7-binding sites on FAM83D are essential for its oncogenic functions. A meta-evaluation of FAM83D revealed that the prognostic impact of FAM83D was independent on molecular subtypes. The higher expression of FAM83D has poorer prognosis. Moreover, high expression of FAM83D confers resistance to chemotherapy in BCs, which is experimentally validated in vitro. We conclude that identification of FBXW7-binding sites on FAM83D not only reveals the importance for FAM83D oncogenic function, but also provides valuable insights for drug target.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2021

All solid thick oxide cathodes based on low temperature sintering for high energy solid batteries

Solid-state batteries (SSBs) could significantly improve the safety and energy density over conventional liquid cells. One key enabling technology is the use of solid electrolytes. NASICON-type Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 (LATP) is a very attractive solid-state electrolyte for the cathode side due to its high oxidation potential and high ionic conductivity. The usage, however, is limited by its large interfacial resistance against most of the cathode materials as well as the thermodynamic instability during high temperature sintering needed to achieve high mass density. Here we construct thin, percolative, and mixed conductive interphases through in situ low-melting-point liquid sintering. These mixed conductive interphases drastically improve the kinetics, leading to high-loading solid LATP/LiCoO 2 cathodes achieving capacity loading of up to ~6 mA h cm –2 . The technique is also applicable to Ni-rich cathode materials, achieving up to ~10 mAh cm –2 , which can lead to more than 400 W h kg –1 cells in SSBs. Furthermore, our composite cathodes show a ten-times and three-times area capacity improvement over the state-of-the-art cathodes using oxide and sulfide SSEs, respectively.

25 ENERGY STORAGE↗

DOE OSTI2021

Systematic Evaluation of Carbon Hosts for High-Energy Rechargeable Lithium-Metal Batteries

Rechargeable lithium batteries (RLBs) have attracted wide attention for achieving high energy and low cost, but the poor stability of the Li anode has remained as a large challenge. In the last several years, great efforts have been made to develop carbon anode structures for RLB applications. A wide range of carbon structures as well as many chemical modification strategies have been investigated to improve the Coulombic efficiency and extend the cycle life of the anodes or the cells. However, currently there is no clear conclusion on key factors that determine the performance of such the types of carbon structures due to the wide range of experimental conditions used in such studies. In this study, we systematically evaluated and compared the electrochemical properties of representative carbon anode materials as well as chemically functionalized carbon materials in different electrolytes. We have found that chemical functionalization, metallic loading, and the types of micro or nano-structures all have an effect on Li deposition/stripping process, but by far the most critical factor is the nature of the electrolytes. All carbon materials produced poor Coulombic efficiency and cycle life in conventional carbonate or ether-based electrolytes. However, when a Li metal compatible is used, the average Coulombic efficiency of Li metal deposition on all carbon structures is increased to 99% or higher. This study provides critical lessons on the directions for carbon anodes for RLBs. Based on these findings, we constructed Li metal coin cells using prelithiated hard carbon, LiNi0.6Mn0.2Co0.2O2 (NMC622) cathode, and compatible electrolyte and tested the cells under conditions of lean electrolyte, lean Li metal and high cathode loading required for more than 300 Wh kg-1 specific energy. More than 200 stable cycles were demonstrated with over 80% capacity retention. Furthermore, the existing challenges and potential approaches have been discussed to further extend the cyclability of lithium-metal batteries under practical conditions.

Liu, Yao↗