Engineering topics
Jiao, Zhijie
Publications and source records attributed to Jiao, Zhijie.
Data on Cu- and Ni-Si-Mn-rich solute clustering in a neutron irradiated austenitic stainless steel
The data presented in this article is supplementary to the research article “Phase instabilities in austenitic steels during particle bombardment at high and low dose rates” (Levine et al.). Needle-shaped samples were prepared with focused ion beam milling from a 304L stainless steel that was irradiated with fast neutrons (E 0.1 MeV) in the BOR-60 reactor at 318 °C to 47.5 dpa. Atom probe tomography (APT) experiments in voltage mode were then conducted on a Cameca LEAP 5000X HR. Atom position, range, and mass spectrum files after reconstruction with Cameca’s IVAS software are included. Cu- and Ni-Si-Mn-rich solute nanoclusters were identified and analyzed using the Open Source Characterization of APT Reconstructions (OSCAR) program. Python code for OSCAR, information on the program’s underlying algorithm, and sample output files are provided. A proximity histogram of a Ni-Si-Mn-rich cluster and a 1D density/solute concentration profile of a Cu-rich cluster are given to demonstrate OSCAR’s analytical functionalities. The provided APT dataset is valuable for benchmarking phase instabilities in neutron-irradiated austenitic stainless steels that occur at high doses. The OSCAR program can be reused to process other APT data sets where solute nanoclustering is of interest.
Synergies between H, He and radiation damage in dual and triple ion irradiation of candidate fusion blanket materials
Three ferritic/martensitic alloys were studied to understand the synergistic effect between single ion beam (Fe 2+ ), dual ion beam (Fe 2+ +He 2+ and Fe 2+ +H + ), and triple ion beam (Fe 2+ +He 2+ +H + ) irradiations on cavity evolution. A commercial alloy, F82H, a castable nanostructured alloy, CNA3, and a high purity model alloy, Fe8Cr2W, were irradiated at 400°C to 600°C to a damage level of 50 dpa at a damage rate of 1 × 10 –3 dpa/s with He and H injection rates of 10 and 40 appm/dpa, respectively. Post-irradiation characterization via bright field transmission electron microscopy and high-angle annular dark-field scanning transmission electron microscopy was performed on all irradiated conditions to characterize the cavity size distribution and determine the effects of H/He injection on cavity microstructure. In all three alloys, hydrogen co-injection with helium resulted in an increased cavity number density and maximum cavity size, producing an increase in swelling over that from helium injection alone. Swelling in F82H appears to peak between 450°C and 500°C. At 600°C, swelling was minimal and cavities of high density and small size were confined to grain boundaries and dislocations while at 400°C, swelling is also low with a nearly homogeneous, high density, distribution of very small cavities throughout. Swelling was least in the commercial alloy F82H due to the high sink strength. The CNA3 alloy underwent dissolution of precipitates that lowered the sink strength and resulted in higher swelling than F82H, but less than the model alloy. Electron energy loss spectroscopy (EELS) elemental mapping revealed hydrogen forming a halo-like structure about the periphery of the cavities and helium residing within the cavities themselves. Finally, this observation suggests that hydrogen reduces the surface energy of helium-filled cavities which results in both increased cavity number density and cavity size in triple beam irradiation over dual beam irradiation.
Solute segregation and precipitation across damage rates in dual-ion–irradiated T91 steel
We report that dual-ion irradiations using 5.0 MeV defocused Fe 2+ ions and co-injected energy degraded 2.00 to 2.85 MeV He 2+ ions were conducted on a Fe9CrMo ferritic-martensitic steel T91 to 17 dpa at a damage rate range of 5 × 10 -5 dpa/s to 3 × 10 -3 dpa/s at 445°C, followed by characterization of the microstructure using conventional and scanning transmission electron microscopy. Radiation induced Ni/Si clusters and radiation induced segregation were quantified using energy dispersive X-ray spectroscopy at each condition and were compared with the same material irradiated in the BOR-60 reactor and in the as-received condition. No significant Cr segregation was found at lath boundaries after dual-ion irradiation, while Ni and Si enrichments both decreased with increasing damage rate leading to a sharp decrease in the density of Ni/Si clusters with damage rate. Increased point defect recombination at higher ion damage rates likely reduced the Ni/Si cluster density compared with BOR-60. Although the overall vacancy concentration and diffusion are enhanced by the irradiation damage rate, the lack of time for thermal diffusion and ballistic displacements of solutes are significant limiting factors for Ni/Si cluster formation. This work demonstrates the effect of irradiation damage rate on elemental segregation and clustering when using ion irradiation to simulate reactor irradiation.
Fission Product Diffusion in Silicon Carbide: As Revealed by Computer Simulations and Experimental Measurements
The diffusion and release of fission products through silicon carbide in the tri-structural isotropic (TRISO) fuel particles remain unsolved for decades. The underlying mechanism is quite challenging to be determined. To help unveil the mysterious story, the current work applies molecular dynamics method to show the stability of silver, palladium, ruthenium and iodine as an interstitial and their atomic diffusion along coincident site lattice (CSL) boundary, especially ?3 grain boundary (GB). The major finding presents a much faster diffusion along GB than in bulk for all elements considered. The reasonably close estimate to experiments and simulations where available has confirmed the important role of grain boundary diffusion of Ag and Pd in SiC. However, the discrepancy addressed in Ag with measurements from fuel studies suggest a more complicated mechanism, which might be in correlation with high energy grain boundaries or the presence of crack. The subsequent characterization of Ru and I distribution in SiC-PyC-SiC diffusion couples, which have been ion irradiated at 900?C to 10 dpa and 20 dpa, has performed by secondary ion mass spectrometry (SIMS) analysis. The experiment measurements correlate well with the grain boundary diffusion by simulation, which provide further evidences that the grain boundary diffusion cannot be neglected once the fission products are accessible at the grain boundary.
Effects of post-irradiation annealing on the IASCC susceptibility of neutron-irradiated 304L stainless steel
Not Available
Emulation of fast reactor irradiated T91 using dual ion beam irradiation
In this work, dual ion irradiations using 5 MeV defocused Fe 2+ ions and co-injected He 2+ ions were conducted on a ferritic-martensitic steel alloy, T91, in the temperature range of 406 °C–570 °C over a damage range of 14.6–35 dpa followed by characterization of the microstructure using transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM). Dislocation loops were observed to increase in diameter and decrease in density with temperature until only network dislocations were observed at the highest temperatures of 520 °C and 570 °C. Swelling exhibited the expected bell-shaped trend with temperature following the number density of cavities, peaking at 460 °C and with a bimodal size distribution except at 520 °C and 570 °C. Nickel- and silicon-rich clusters formed under dual ion irradiations near the surface at all but the highest temperatures of 520 °C and 570 °C. Very little Cr and Si segregation was observed at lath boundaries while Ni enriched at all temperatures examined. Segregation of Cr and Ni appeared to saturate by 17 dpa, while Si enriched up to 35 dpa. The dislocation and cavity microstructures of dual ion irradiated T91 and T91 irradiated in the BOR-60 fast reactor matched extremely well using a temperature shift of +60–70 °C. However, segregation to grain boundaries and formation of nickel-silicon rich clusters were minimal in the dual ion irradiated T91 and less than that in T91 irradiated in the BOR-60 fast reactor.
Reveal the fast and charge-insensitive lattice diffusion of silver in cubic silicon carbide via first-principles calculations
The lattice diffusion of silver with various charge states in cubic silicon carbide has been investigated by means of high-fidelity spin-polarized density functional theory calculations. The migration energy barrier of the Ag interstitial diffusion is 1.09 eV and 1.11 eV for neutral and q = +1e charge state, respectively, close to the activation energy of Ag diffusion measured in the German HTR fuel program. A general trend is that the migration energy barrier reduces with respect to the increase of charge on Ag, which is much less than the increment in the oxidation energy, suggesting that the lattice diffusion of silver prefers constant neutral state without redox in transition state. Furthermore, our results indicate a scenario that once Ag is deposited to interstitials via the kickout mechanism, it will highly likely perform lattice diffusion across the SiC layer leading to fast release of Ag in Tristructural-Isotropic fuel induced by irradiation.
Ab initio study of the stability of intrinsic and extrinsic Ag point defects in 3C SiC
Not Available
The influence of carbon on cavity evolution in ion-irradiated ferritic-martensitic steels
Not Available
The influence of helium on cavity evolution in ion-irradiated T91
Not Available
Multiple ion beam irradiation for the study of radiation damage in materials
Not Available
Accelerated Irradiations for High Dose Microstructures in Fast Reactor Alloys
The objective of this project is to determine the extent to which high dose rate, self-ion irradiation can be used as an accelerated irradiation tool to understand microstructure evolution at high doses and temperatures relevant to advanced fast reactors. We will accomplish the goal by evaluating phase stability and swelling of F-M alloys relevant to SFR systems at very high dose by combining experiment and modeling in an effort to obtain a quantitative description of the processes at high and low damage rates.
Microstructural processes in irradiated materials
This is an editorial article (preface) for the publication of symposium papers in the Journal of Nuclear materials: These proceedings contain the papers presented at two symposia, the Microstructural Processes in Irradiated Materials (MPIM) and Characterization of Nuclear Reactor Materials and Components with Neutron and Synchrotron Radiation, held in the TMS 2015, 144th Annual Meeting & Exhibition at Walt Disney World, Orlando, Florida, USA on March 15–19, 2015.