Search NASA⌕ Search

Engineering topics

Jin Ho Kang

Publications and source records attributed to Jin Ho Kang.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2026

Cryogenic Mixed Mode I – Mode II Fracture Toughness of Various Polymer Composite Materials

The present study investigates the mixed mode interlaminar fracture toughness of six polymer matrix composite materials at both room temperature and cryogenic liquid nitrogen temperature. The single leg bending test employed gives a mix of Mode I (opening) and Mode II (in-plane shearing) cracking. The tested thermoplastic-matrix composites were shown to have total mixed mode toughnesses 3.1–4.3 times higher than those of representative thermoset resin composites.

Carbon fiber↗
NASA NTRS2026

A Study of Space Environment Effect on Highly Thermally Conductive Hybrid Carbon Fiber Polymer Composites

A set of novel highly thermally conductive hybrid carbon fiber (CF) polymer composites has been developed for lightweight thermal radiator applications in space missions. This study investigates the effects of the space environment on these materials following exposure in low-Earth orbit (LEO) during the Materials International Space Station Experiment (MISSE)-17 flight mission, where samples experienced 159 days of combined atomic oxygen (AO), ultraviolet (UV) radiation, high vacuum, space radiation and thermal cycling. Post-flight characterization included weight loss, surface morphology, thermo-optical properties, molecular structures, glass transition temperature, thermal degradation and thermal conductivity analyses. The pyrolytic graphite sheet (PGS) samples exhibited negligible weight loss, stable thermo-optical property, and only minor oxidation signature on the exposed surface. Although AO erosion of the epoxy polymer matrix was evident, carbon nanotube (CNT)-infused PGS/CF epoxy composites retained high thermal emissivity and preserved their high thermal conductivities. These results demonstrate that the novel highly thermally conductive hybrid CF composites possess strong environmental resilience and are promising candidates for lightweight thermal radiators and thermal management components in future space exploration missions.

Space Environment↗
NASA NTRS2024

Offset-Stoichiometric Reflowable Composite Bonding Method with Adhesive for Mitigating Strict Faying Surface Tolerances

Inherent susceptibility of adhesive bonds to miniscule quantities of contamination can cause undetectable weakened bonds. For this reason, the Federal Aviation Administration (FAA) places strict regulations on adhesively bonded joints in primary aircraft structures. To meet certification requirements aircraft manufactures resort to redundant load paths in the form of fasteners which inherently add weight to the structure and increase manufacturing time. In prior work, a secondary bonding technique called AERoBOND was developed, which utilized off-stoichiometric epoxymatrix resins to facilitate reflow and diffusion of the resin within the joint interface during a secondary bonding/cure process, thus achieving a bond similar to a co-cured joint. However, the AERoBOND process required tight spatial tolerances between the two parts being joined. This study examined the utilization of conventional adhesive with the AERoBOND method to act as a filler in the joint line, effectively reducing the need for tight tolerances on the joining parts and serving as a flexible alternative for existing manufacturing processes. Ultrasonic inspection, optical microscopy, and ASTM International standard tests were performed to analyze the joints for defects and to quantify the mode-I and mode-II interlaminar fracture toughness and short beam strength of the proposed methodology with varying manufacturing parameters. The comprehensive results indicate that the AERoBOND+ method with and without surface preparation performs comparably to co-cured and conventional, adhesively bonded joints when secondary cured in an autoclave with 791 kPa of pressure. As an example, the AERoBOND+ panel without surface preparation bonded with 791 kPa of pressure (referred to as AB+3 throughout paper) had a mode-I fracture toughness (G Ic ) of 0.643 kJ/m 2 and a mode-II fracture toughness (G IIc ) of 4.000 kJ/m 2 in the non-precracked condition and 4.218 kJ/m 2 in the precracked condition at the adhesive-to-prepreg interface. These results were 96%, 142%, and 217%, respectively, of a co-cured baseline panel (referred to as C1 throughout paper).

Composites↗
NASA NTRS2023

Ultrasonic Inspection During Autoclave Cure of Reflowable-Interface Composite Joints

In structural bonds, the interface between adherend and adhesive is nearly two-dimensional making the interface susceptible to minute quantities of contamination, which can cause weak bonds. Regulatory organizations such as the Federal Aviation Administration (FAA) often require redundant load paths in secondary-bonded primary-structures due to uncertainty in bond performance. To address this issue, the NASA Convergent Aeronautics Solutions (CAS): Adhesive Free Bonding of Composites (AERoBOND) project is investigating reformulated aerospace epoxy-matrix resins to enable reflow and diffusion of the resin at the joint interface during a secondary bonding and cure process that can eliminate the material discontinuity at the interface. Implementing in-situ process monitoring enables assessing the bond quality during processing rather than waiting for post-fabrication mechanical testing to be completed. In this paper, an in-situ ultrasonic inspection system is used to monitor the joining of three composite laminates assembled using the AERoBOND technique. For each panel, the amplitude of the wave reflection at the joint was measured throughout the cure cycle. The results indicate the timing and extent of reflow and cure of the epoxy resin at the joint. Factors indicating end of cure were ascertained and a metric was developed to qualitatively predict acceptable mode-II fracture toughness based on the ultrasonic amplitude at the joint line during cure. In addition, since the inspection system scans an area of the joint, high-resolution localized results can be obtained across the joint.

Tyler B Hudson↗
NASA NTRS2022

Epoxy Resins with Reduced Viscoelastic Relaxation

The payloads of current space launch systems, e.g. rockets, are constrained to a small size due to aerodynamic, weight, and cost limitations. Deployable structures allow for a folded or stowed configuration during launch and deployment at the mission location. Polymer composites have shown both high weight savings over current metallic structure, as well as improved specific mechanical strengths overall. One issue encountered with polymer composite deployables, however, is stress relaxation of the polymer matrix in the stowed configuration. In this study, a range of different epoxy formulations were evaluated as potential matrix resins for deployable composites. A new multifunctional epoxy resin with a fortifying additive is predicted to show 70% less stress relaxation after 1 year as compared to a state-of-the-art aerospace epoxy matrix.

Ray S. Peterson↗
NASA NTRS2021

Latent Cure Epoxy Resins for Reliable Joints in Secondary-Bonded Composite Structures

In high-performance polymer matrix composite assemblies, adhesive bonding is generally superior to mechanical fastening in structural performance and manufacturing efficiency. However, adhesive bonds are susceptible to minute levels of contamination accumulated during assembly that can lead to unpredictable, weak bonds. Current methods of measuring bond strength are all destructive mechanical tests. To overcome these challenges, redundant load paths (e.g., mechanical fasteners) are often implemented in secondary-bonded, primary-structures, which can greatly reduce structural performance. This study investigated reformulated aerospace epoxy matrix resins with stoichiometric offset to inhibit cure of the matrix resin prior to assembly. Inhibited resins can reflow and mix across the joint interface, which eliminates the material discontinuity and forms a homogenous joint with reliable fracture properties. The goal of this study was to develop and demonstrate secondary composite assemblies that are mechanically and microscopically indistinguishable from a co-cured composite joint. This article describes the development of latent epoxy resins, the fabrication of test articles, and the mechanical properties measured from experimental joints compared with conventional, co-cured laminates. Methods of in-line quality control using and infrared spectroscopy and post-assembly forensics are also described. The final mode-II fracture toughness measured from precracked AERoBOND specimens was similar to that measured from co-cured laminates indicating that later cure epoxy materials could be a suitable replacement for secondary bonding.

Polymer-matrix composites (PMCs)↗
NASA NTRS2021

Molecular Dynamics Investigation of the Structural and Mechanical Properties of Off-Stoichiometric Epoxy Resins

Molecular dynamic (MD) simulations were performed to compute the mechanical properties of off-stoichiometric epoxy resins as a function of hardener/epoxy mixture ratio (r). Properties were characterized in relation to their microscopic structures. Such resins have been used recently for adhesive-free bonding of large-scale composite structures using the co-curing-ply method. In this process, two partially precured composite panels with hardener-poor (HP) off-stoichiometric resins are coupled with ply(ies) of complementary hardener-rich (HR) formulations and then cured simultaneously. This bonding process has the potential to produce reliable and certifiable composite joints without the need for additional fasteners, which are often required for many conventional bonding methods because even small amounts of contamination can cause a weak bond. The reflow and mixing of the HP/HR resin in this bonding process result in a joint with no discernable interface that should not be susceptible to surface contamination. However, incomplete mixing of the two offset resins may result in chemical heterogeneity of the cured polymeric joint. Thus, different r values may be obtained across the joint. Classical MD simulations were performed to compute the Young’s modulus of polymers with different r values and correlate their properties to network structures. High stiffness was associated with molecular packing due to chemical crosslinking, leading to a single network structure. Moreover, the networks became denser as the ratio approached the stoichiometric value r = 1. Thus, the r = 1 systems were single clusters, with high stiffness, high molecular weight, and a high degree of crosslinking. Structural properties such as radius of gyration and mean square displacement were determined to investigate the variation in the stiffness with respect to r. This MD simulation study was validated with experimental measurements.

Chang Woon Jang↗
NASA NTRS2021

Machine Learning to Predict Joint Performance in Epoxy Composites Based on Process Parameters

Polymer matrix composites are gaining popularity in the aerospace industry due to their high specific strength, fatigue properties, and processability. However, based on current FAA certification guidelines, manufacturers utilizing current state-of-the-art composites made with adhesive bonds commonly install redundant fasteners to guarantee the strength of these adhesively bonded composite parts. The number of fasteners in a single-aisle commercial transport aircraft is typically on the order of 105, which reduces manufacturing rate, increases cost tremendously, and reduces the advantage of the specific strength composites provide. Due to this, the Adhesive Free Bonding of Composites (AERoBOND) project at NASA Langley Research Center has developed a novel assembly process to manufacture complex composite parts without the use of adhesives and fasteners. However, optimization of the process is currently challenging due to the complex and interdependent process parameters. To assist with the optimization, four machine learning algorithms utilizing gradient boosting decision trees were created to provide predictions for the mechanical and characterization properties of the composite parts. Approximately 200 random states from each algorithm were tested, and the models from each state were isolated and analyzed based on their accuracy, a validation process, and their feature importance. This analysis concluded that the models created from the machine learning algorithms could accelerate a parametric study for the AERoBOND process by rapidly optimizing process parameters to achieve desired performance characteristics.

Brennen Michael Middleton↗
NASA NTRS2020

Novel High Barrier Films for Packaging Food and Medicine

Long manned missions require food packaging to maintain food safety, nutrition, and acceptability for the length of 3-5 years1,2 while the shelf life assigned by NASA for current provisions is 18-24 months1. The focus of this design project was to make a polymer film specifically to function as a high oxygen barrier to later be included in an improved multi-layer packaging system of other specialized polymers with capabilities to allow for a 5-year shelf-life. To qualify as a high oxygen barrier film and to be a successful design for the future packaging, the resulting film is required to have an oxygen transmission rate (OTR) less than 0.06 cc/ m2/24 hr/atm, the standard for the current packaging3. This new film was designed to have a decreased permeability by increasing the “tortuous path” a gas molecule travels to permeate through a film. The increase in the “tortuous path” of a gas molecule is accomplished by introducing a 2D material additive. The additive chosen for this project was hexagonal boron nitride (h-BN) which exfoliates into boron nitride nanosheets (BNNs). Nylon 6 was chosen as the candidate for the matrix. This project is required to determine the best methods to synthesize the sample film and then to test the OTR of the film to determine if this design was successful. This project examined methods for pulverizing polymer resin pellets, h-BN exfoliation, and film fabrication using a hot press. This report includes the exfoliation and analysis of h-BN, procedural preparations for films, and a modeling study of estimated OTR of the h-BN/Nylon. The work in this report did not yield a high barrier composite film because of the laboratory closure in response to COVID -19 guidance but provides a concise method of the additive preparation and film synthesis. This gives a good starting point for future research in high barrier films by 2D additive composites.

Polymer, Nylon, PET, boron nitride, nanocomposite↗
NASA NTRS2020

Reduced Dependence on Redundant Fasteners in Secondary-Bonded Composite Structures Using Modified Epoxy Matrix Resins

This report describes a sub-set of over 20 experiments conducted to optimize materials and processes to maximize mechanical properties of the assembled joint. Infrared (IR) spectroscopy was used to measure the chemical state of the ER surface after primary cure. Laminates were fabricated with various HR and ER layer thicknesses, inspected using ultrasonic testing, and mechanically tested to measure fracture toughness.

Frank L Palmieri↗
NASA NTRSDate not supplied

Advances in Low-Cost Manufacturing and Folding of Solar Sail Membrane

Solar sail membranes must have a high area-to-mass ratio and high solid volume fraction when stowed. In order to meet mission requirements, current solar sail projects, such as the NASA Near Earth Asteroid Scout and Advanced Composite Solar Sail System, require metallized sail membranes with thicknesses on the order of 2-3 μm. These very thin membranes do not retain creases like thicker membranes, solar panels, or paper models. For CubeSat-class spacecraft, volume, rather than mass, is often the driving requirement for deployable structural elements. These two factors make it both difficult and highly desirable to characterize the practical differences between various membrane designs and packaging methods with laboratory demonstrations. This paper presents lessons gathered from lab work on solar sail membranes at a 9-meter scale. Among other results, laboratory deployment of a full-scale sail quadrant revealed important differences between seaming methods.

Olive R Stohlman↗
NASA NTRSDate not supplied

Modified Epoxy Matrix Resins for Reduced Dependence on Redundant Fasteners in Secondary-Bonded Composite Structures

In structural bonds, the interface between adherend and adhesive is nearly two-dimensional making it susceptible to minute quantities of contamination that can lead to weak bonds. No methods currently exist to measure the strength of an adhesive bond nondestructively. For these reasons, regulating organizations such as the Federal Aviation Administration (FAA) often require redundant load paths in secondary-bonded, primary-structures to achieve certification for civil transport aircraft. To meet this requirement, manufacturers commonly install redundant fasteners (~105 fasteners in a twin-aisle airframe with composite fuselage and wings), which add tremendous complexity, time and cost, and significantly reduce performance of the airframe. Under NASA’s Convergent Aeronautics Solutions (CAS) Program, the Adhesive Free Bonding of Composites (AERoBOND) project is investigating reformulated aerospace epoxy matrix resins to enable reflow and diffusion of the resin at the interface during a secondary bonding/cure process. The mixing process eliminates the material discontinuity at the interface, thereby removing the dependence of bond performance on adhesion across a nearly two-dimensional boundary. The AERoBOND interface is similar to the interlaminar region formed during a co-cure process, so joint performance depends on the cohesive properties of the matrix resin, which can be measured, inspected non-destructively, and certified for flight with fewer redundant fasteners. This presentation describes the ongoing development of stoichiometrically-offset epoxy resins to control the degree of cure in composite joints and enable interfacial mixing during secondary bonding/curing. Details on the resin formulation, laminate fabrication, and mechanical testing will also be presented. The precracked mode-II fracture toughness measured from preliminary AERoBOND joints was similar for joints fabricated with conventional epoxy matrix materials.

thermoset, hardener, prepreg, assembly↗
NASA NTRSDate not supplied

In-situ Inspection of Reflowable-Interface Composite Joints During Cure in an Autoclave

In structural bonds, the interface between adherend and adhesive is nearly two-dimensional making it susceptible to minute quantities of contamination, which can cause weak bonds. Regulatory organizations such as the Federal Aviation Administration (FAA) often require redundant load paths in secondary-bonded, primary-structures to alleviate concerns with bonded performance. Under NASA’s Convergent Aeronautics Solutions (CAS) project, the Adhesive Free Bonding of Composites (AERoBOND) project is investigating reformulated aerospace epoxy-matrix resins to enable reflow and diffusion of the resin at the joint interface during a secondary bonding and cure process. The reflow and intermixing of the matrix resin during assembly can eliminate the material discontinuity at the interface, thereby removing the dependence of bond performance on adhesion at a nearly two-dimensional boundary. AERoBOND process development has evaluated a multitude of parameters including the materials used, the stoichiometric offset of the epoxy resins, time and temperature of cure, and thickness of each ply. Without in-situ process monitoring, the condition of a test article is unknown until mechanical testing is completed. This presentation describes the use of an in-situ ultrasonic inspection system to monitor the joining of two composite parts assembled using the AERoBOND technique. This work quantifies the elimination of the interface by measuring the wave reflection, or lack thereof, at the joint throughout the cure cycle. In addition, the results indicate when reflow and cure of the epoxy resin at the joint occurred. By using the recently developed in-situ inspection with a mobile ultrasonic transducer, localized results can be obtained across a large portion of the joint with high resolution.

Tyler B Hudson↗
NASA NTRSDate not supplied

In-situ Inspection of Reflowable-Interface Composite Joints During Cure in an Autoclave

In structural bonds, the interface between adherend and adhesive is nearly two-dimensional making it susceptible to minute quantities of contamination, which can cause weak bonds. Regulatory organizations such as the Federal Aviation Administration (FAA) often require redundant load paths in secondary-bonded, primary-structures to alleviate concerns with bonded performance. Under NASA’s Convergent Aeronautics Solutions (CAS) project, the Adhesive Free Bonding of Composites (AERoBOND) project is investigating reformulated aerospace epoxy-matrix resins to enable reflow and diffusion of the resin at the joint interface during a secondary bonding and cure process. The reflow and intermixing of the matrix resin during assembly can eliminate the material discontinuity at the interface, thereby removing the dependence of bond performance on adhesion at a nearly two-dimensional boundary. AERoBOND process development has evaluated a multitude of parameters including the materials used, the stoichiometric offset of the epoxy resins, time and temperature of cure, and thickness of each ply. Without in-situ process monitoring, the condition of a test article is unknown until mechanical testing is completed. This presentation describes the use of an in-situ ultrasonic inspection system to monitor the joining of two composite parts assembled using the AERoBOND technique. This work quantifies the elimination of the interface by measuring the wave reflection, or lack thereof, at the joint throughout the cure cycle. In addition, the results indicate when reflow and cure of the epoxy resin at the joint occurred. By using the recently developed in-situ inspection with a mobile ultrasonic transducer, localized results can be obtained across a large portion of the joint with high resolution.

Tyler B Hudson↗