Search NASA⌕ Search

Engineering topics

Jin, Tianwei

Publications and source records attributed to Jin, Tianwei.

6 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Designing electrolytes with high solubility of sulfides/disulfides for high-energy-density and low-cost K-Na/S batteries

Alkaline metal sulfur (AMS) batteries offer a promising solution for grid-level energy storage due to their low cost and long cycle life. However, the formation of solid compounds such as M 2 S 2 and M 2 S (M = Na, K) during cycling limits their performance. Here we unveil intermediate-temperature K-Na/S batteries utilizing advanced electrolytes that dissolve all polysulfides and sulfides (K 2 S x , x = 1–8), significantly enhancing reaction kinetics, specific capacity, and energy density. These batteries achieve near-theoretical capacity (1655 mAh g -1 sulfur) at 75 °C with a 1 M sulfur concentration. At a 4 M sulfur concentration, they deliver 830 mAh g -1 at 2 mA cm -2 , retaining 71% capacity after 1000 cycles. This new K-Na/S battery with specific energy of 150-250 Wh kg -1 only employs earth-abundant elements, making it attractive for long-duration energy storage.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Electrochemical Characterization of Degradation Modes of High-Voltage Li x Ni 0.33 Mn 0.33 Co 0.33 O 2 Electrodes

While deeply charged high-voltage cathodes can improve battery energy density, understanding and preventing any accelerated cell degradation is crucial to practical success. Here, to analyze the degradation of LiNi x Mn y Co 1–x–y O 2 (NMC) type material charged to 4.3 and 4.5 V, a physics-based model is applied to cycling data to obtain parameter estimates indicative of degradation modes, which are validated by simple electrochemical measurements and further interpreted by materials characterization. Growth rates of interfacial impedance and active material loss are greater at 4.5 V, as might be expected. However, when charged to 4.5 V, degradation rates are initially lower at a cycling C-rate of 1.0 C than at 0.5 C. Once degradation mode changes are quantified, simulations evaluate the contribution of individual degradation mode to performance losses and provide estimates of the energy-power correlation (Ragone plots) of cells after cycling.

25 ENERGY STORAGE↗
DOE OSTI2022

Modeling Isotope Separation in Electrochemical Lithium Deposition

Naturally occurring Li consists of two stable isotopes, 6 Li with an abundance of about 7.5%, and 7 Li making up the remainder with 92.5%. The development of a 6 Li enrichment technique, in terms of technical reliability and environmental safety to reach 6 Li future requirements, represents a key step in the roadmap for nuclear fusion energy supply worldwide. This paper uses finite element analysis-based models to simulate electrochemical Li isotope separation, which is an attractive method in terms of simplicity, safety, and scalability. In the model, we quantitatively analyze how different electrochemical factors including thermodynamics, charge-transfer kinetics, and diffusivities affect the separation process (separation factor), together with cell parameters, such as cell length and current density. The maximum separation factor of 1.128 could be obtained with the cell under the optimal thermodynamic, kinetic, and diffusive conditions, which is among the highest separation factors ever reported. Furthermore, these results will assist in designing the actual isotope separation setup with large separation factor and appropriate timing for sample collection.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2021

Chemical Heterogeneity in PAN/LLZTO Composite Electrolytes by Synchrotron Imaging

Solid polymer/ceramic composite electrolytes are promising for batteries due to their attractive thermal stability and mechanical properties. Chemical heterogeneity in solid composite electrolytes, such as the inhomogeneity in the ceramic phase and salt distribution at the polymer/ceramic interface, is critical to the performance of solid composite electrolytes. However, such heterogeneity has not been well understood yet. In this work, we use Synchrotron-based X-ray fluorescence imaging (XRF) and Transmission X-ray Microscope (TXM) to image nanoscale chemical heterogeneity in polyacrylamide/Li 7+x La 3 Zr 2–x Ta x O 12 (LLZTO) composite electrolytes and investigate the effects of lithium salt, salt concentration, and plasticizer. We find that LLZTO particles show strong inter- and intra-particles chemical heterogeneities, and the off-stoichiometry of Zr in an LLZTO particle is unlikely to be only balanced by Ta substitution. Moreover, statistical analysis suggests that LiI tends to accumulate at the ceramic/polymer interface at a low concentration of 5 wt%, but no such tendency was observed in samples with 10 wt% LiI. However, composite electrolytes with LiTFSI show interfacial accumulation at both 5 wt% and 10 wt%. Furthermore, this report provides insight into element distributions in solid composite electrolytes, and we hope further researches can shed light on the connections between chemical heterogeneity and ionic transport pathway inside.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Interfacial engineering for stabilizing polymer electrolytes with 4V cathodes in lithium metal batteries at elevated temperature

Poly (ethylene oxide) (PEO) polymer electrolytes are promising candidates for next-generation rechargeable lithium batteries. However, the poor interfacial stability between 4 V cathodes and PEO electrolytes impedes their applications in 4 V lithium batteries with high energy density. Here, we demonstrate a facile and effective strategy to enhance the interfacial stability by the synergy of Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 (LAGP) coating on the cathode surface, and salt combination in the electrolyte, even with a cut-off voltage of 4.25–4.4 V vs. Li + /Li. Nano-LAGP coated Li|PEO|LiCoO 2 cell delivers stable cycling with a capacity retention of 81.9%/400 cycles and 84.7%/200 cycles at 60 °C when charged to 4.25 and 4.3 V in pure polyether electrolyte, respectively. Steady cycling is also demonstrated at room temperature and with LiNi 0.5 Co 0.2 Mn 0.3 O 2 (NCM523) cathode. This work offers a viable and scalable approach to improve the stability between PEO electrolytes and 4 V cathodes and open up new possibilities for practical application of 4 V lithium metal batteries.

25 ENERGY STORAGE↗