Search NASA⌕ Search

Engineering topics

Joffrin, E.

Publications and source records attributed to Joffrin, E..

At least 19 records

Helium plasma operations on ASDEX Upgrade and JET in support of the non-nuclear phases of ITER

For its initial operational phase, ITER has until recently considered using non-nuclear hydrogen (H) or helium (He) plasmas to keep nuclear activation at low levels. To this end, the Tokamak Exploitation Task Force of the EUROfusion Consortium carried out dedicated experimental campaigns in He on the ASDEX Upgrade (AUG) and JET tokamaks in 2022, with particular emphasis put on the ELMy H-mode operation and plasma-wall interaction processes as well as comparison to H or deuterium (D) plasmas. Both in pure He and mixed He + H plasmas, H-mode operation could be reached but more effort was needed to obtain a stable plasma scenario than in H or D. Even if the power threshold for the LH transition was lower in He, entering the type-I ELMy regime appeared to require equally much or even more heating power than in H. Suppression of ELMs by resonant magnetic perturbations was studied on AUG but was only possible in plasmas with a He content below 19%; the reason for this unexpected behaviour remains still unclear and various theoretical approaches are being pursued to properly understand the physics behind ELM suppression. The erosion rates of tungsten (W) plasma-facing components were an order of magnitude larger than what has been reported in hydrogenic plasmas, which can be attributed to the prominent role of He 2+ ions in the plasma. For the first time, the formation of nanoscale structures (W fuzz) was unambiguously demonstrated in H-mode He plasmas on AUG. However, no direct evidence of fuzz creation on JET was obtained despite the main conditions for its occurrence being met. The reason could be a delicate balance between W erosion by ELMs, competition between the growth and annealing of the fuzz, and coverage of the surface with co-deposits.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Observation of alpha-particles in recent D–T experiments on JET

The fusion reaction between deuterium and tritium, D(T,n) 4 He is the main source of energy in future thermonuclear reactors. Alpha-particles ( 4 He-ions) born with an average energy of 3.5 MeV transferring energy to the thermal plasma during their slowing down, should provide the self-sustained D–T plasma burn. The adequate confinement of α-particles is essential to provide efficient heating of the bulk plasma and steady burning of a reactor plasma. That is why the fusion-born α-particle studies have been a priority task in the second D–T experiments (DTE2) on the Joint European Torus (JET) to understand the main mechanisms of their slowing down, redistribution and losses and to develop optimal plasma scenarios. JET with Be-wall and W-divertor, enhanced auxiliary heating systems and improved energetic-particle diagnostic capabilities, producing significant population of α-particles, provided the possibility for comprehensive studying of the α-particle behaviour. Selected results of the confined and lost α-particle measurements, evidence of α-particle self-heating and assessments of the fusion performance are presented in this paper giving an opportunity for further modelling and extrapolation to the International Thermonuclear Experimental Reactor and burning plasma reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Interaction of SPI pellets with plasma on JET and associated disruptions

Abstract The presented data refer to the Shattered Pellet Injector (SPI) experiments carried out at JET in 2019–2020. This paper is a full journal version of the data originally presented as posters at TMPDM_2020 and EPS_2021. This paper presents various aspects of the interaction of pellets with plasma and associated disruptions. The experiment was performed with I p = (1.1–3.1) MA plasmas and mainly with Ne + D 2 pellet composition, but also with Ar pellets. The Current Quench (CQ) time, τ 80−20 , is the key characteristic of mitigation effectiveness. A pellet with a high content of Ne or Ar can reduce the CQ duration below the upper required JET threshold. Plasmas with high (thermal + internal poloidal magnetic) pre-disruptive plasma energy require a high content of Ne pellets to obtain a short CQ duration. Pellets with a small amount of Ne (and accordingly large amount of D), instead of causing a mitigated CQ, create the conditions for a ‘cold’ Vertical Displacement Events (VDE). The SPI was applied to plasma with different status: mainly to normal (‘healthy’) plasma, i.e. not prone to disruption, post-disruptive and VDE plasma. This study shows that SPI effectiveness in terms of CQ duration and, accordingly, EM loads does not depend on the state of the plasma, whether it is ‘healthy’ or post-disruptive plasma. SPI has been shown to reduce the axisymmetric vertical vessel reaction forces by about (30–40) % compared to unmitigated disruptions. On JET, the VDE, whether ‘hot’ or ‘cold’, always creates the conditions for a toroidal asymmetry in the plasma, so the VDE on the JET is referred to as Asymmetric VDE (AVDE). The interrupting of VDE and prevention of AVDE with SPI has been demonstrated. Thus, the effectiveness of disruption mitigation using SPI has been confirmed.

Gerasimov, S. N. (ORCID:0009000237937211)↗

3D radiated power analysis of JET SPI discharges using the Emis3D forward modeling tool

Abstract Precise values for radiated energy in tokamak disruption experiments are needed to validate disruption mitigation techniques for burning plasma tokamaks like ITER and SPARC. Control room analysis of radiated power ( P rad ) on JET assumes axisymmetry, since fitting 3D radiation structures with limited bolometry coverage is an under-determined problem. In mitigated disruptions, radiation is toroidally asymmetric and 3D, due to fast-growing 3D MHD modes and localized impurity sources. To address this problem, Emis3D adopts a physics motivated forward modeling (‘guess and check’) approach, comparing experimental bolometry data to synthetic data from user-defined radiation structures. Synthetic structures are observed with the Cherab modeling framework and a best fit chosen using a reduced χ 2 statistic. 2D tomographic inversion models are tested, as well as helical flux tubes and 3D MHD simulated structures from JOREK. Two nominally identical pure neon shattered pellet injection (SPI) mitigated discharges in JET are analyzed. 2D tomographic inversions with added toroidal freedom are the best fits in the thermal quench (TQ) and current quench (CQ). In the pre-TQ, 2D reconstructions are statistically the best fits, but are likely over-optimized and do not capture the 3D radiation structure seen in fast camera images. The next-best pre-TQ fits are helical structures that extend towards the high-field side, consistent with an impurity flow under the magnetic nozzle effect also observed in JOREK simulations. Whole-disruption radiated fractions of 0.98 + 0.03 / − 0.29 and 1.01 + 0.02 / − 0.17 are found, suggesting that the stored energy may have been fully mitigated by each SPI, although mitigation efficiencies well below ITER and SPARC requirements for high energy pulses are still within the large uncertainties. Emis3D is also used to validate JOREK SPI simulations, and confirms improvements in matching experiment from changes to impurity modeling. Time-dependent toroidal peaking factors are calculated and discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The JET hybrid scenario in Deuterium, Tritium and Deuterium-Tritium

The JET hybrid scenario has been developed from low plasma current carbon wall discharges to the record-breaking Deuterium-Tritium plasmas obtained in 2021 with the ITER-like Be/W wall. The development started in pure Deuterium with refinement of the plasma current, and toroidal magnetic field choices and succeeded in solving the heat load challenges arising from 37 MW of injected power in the ITER like wall environment, keeping the radiation in the edge and core controlled, avoiding MHD instabilities and reaching high neutron rates. The Deuterium hybrid plasmas have been re-run in Tritium and methods have been found to keep the radiation controlled but not at high fusion performance probably due to time constraints. For the first time this scenario has been run in Deuterium-Tritium (50:50). These plasmas were re-optimised to have a radiation-stable H-mode entry phase, good impurity control through edge T i gradient screening and optimised performance with fusion power exceeding 10 MW for longer than three alpha particle slow down times, 8.3 MW averaged over 5 s and fusion energy of 45.8 MJ.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

L-H transition studies in tritium and deuterium–tritium campaigns at JET with Be wall and W divertor

The recent deuterium–tritium campaign in JET-ILW (DTE2) has provided a unique opportunity to study the isotope dependence of the L-H power threshold in an ITER-like wall environment (Be wall and W divertor). Here we present results from dedicated L-H transition experiments at JET-ILW, documenting the power threshold in tritium and deuterium–tritium plasmas, comparing them with the matching deuterium and hydrogen datasets. From earlier experiments in JET-ILW it is known that as plasma isotopic composition changes from deuterium, through varying deuterium/hydrogen concentrations, to pure hydrogen, the value of the line averaged density at which the threshold is minimum, ${\bar n_{{\text{e}},{\text{min}}}}$, increases, leading us to expect that ${\bar n_{{\text{e}},{\text{min}}}}$(T) < ${\bar n_{{\text{e}},{\text{min}}}}$(DT) < ${\bar n_{{\text{e}},{\text{min}}}}$(D) < ${\bar n_{{\text{e}},{\text{min}}}}$(H). The new power threshold data confirms these expectations in most cases, with the corresponding ordering of the minimum power thresholds. We present a comparison of this data to power threshold scalings, used for extrapolation to future devices such as ITER and DEMO.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The role of isotope mass and transport for H-mode access in tritium containing plasmas at JET with ITER-like wall

The required heating power, $P_{\mathrm{LH}}$, to access the high confinement regime (H-mode) in tritium containing plasmas is investigated in JET with ITER-like wall at a toroidal magnetic field of $B_t = 1.8$ T and a plasma current of $I_p = 1.7$ MA. $P_{\mathrm{LH}}$, also referred to as the L-H power threshold, is determined in plasmas of pure tritium as well as mixtures of hydrogen with tritium (H-T) and mixtures of deuterium with tritium (D-T), and is compared to the L-H power threshold in plasmas of pure hydrogen and pure deuterium. It is found that, for otherwise constant parameters, $P_{\mathrm{LH}}$ is not the same in plasmas with the same effective isotope mass, $A_{\mathrm{eff}}$, when they differ in their isotope composition. Thus, $A_{\mathrm{eff}}$ is not sufficient to describe the isotope effect of $P_{\mathrm{LH}}$ in a consistent manner for all considered isotopes and isotope mixtures. The electron temperature profiles measured at the L-H transition in the outer half of the radius are very similar for all isotopes and isotope mixtures, despite the fact that the L-H power threshold varies by a factor of about six. This finding, together with the observation of an offset linear relation between the L-H power threshold, $P_{\mathrm{LH}}$, and an effective heat diffusivity, $\chi_{\mathrm{eff}}$, indicates that the composition-dependent heat transport in the low confinement mode (L-mode) determines, how much power is needed to reach the necessary electron temperatures at the edge, and hence $P_{\mathrm{LH}}$.

tritium plasmas↗

Isotope effects on intrinsic rotation in hydrogen, deuterium and tritium plasmas

The isotope effect on intrinsic rotation was studied at the Joint European Torus (JET) tokamak. With the unique capability of JET to operate with tritium (T), for the first time, experiments in hydrogen (H), deuterium (D) and T in Ohmic plasmas were compared. Two rotation reversals per isotope type are observed in plasma density scans spanning the linear and the saturated Ohmic confinement regimes. A clear isotope mass dependence is observed at the higher densities. The magnitude of the core rotation was found to depend on isotope mass, with stronger co-current rotation observed in H. Change on intrinsic rotation characteristics coexist with a stronger thermal energy confinement in T.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Physics of runaway electrons with shattered pellet injection at JET

Runaway electrons (REs) created during tokamak disruptions pose a threat to the reliable operation of future larger machines. Experiments using shattered pellet injection (SPI) have been carried out at the JET tokamak to investigate ways to prevent their generation or suppress them if avoidance is not sufficient. Avoidance is possible if the SPI contains a sufficiently low fraction of high-Z material, or if it is fired early in advance of a disruption prone to runaway generation. These results are consistent with previous similar findings obtained with Massive Gas Injection. Suppression of an already accelerated beam is not efficient using High-Z material, but deuterium leads to harmless terminations without heat loads. This effect is due to the combination of a large magnetohydrodynamic instability scattering REs on a large area and the absence of runaway regeneration during the subsequent current collapse thanks to the flushing of high-Z impurities from the runaway companion plasma. This effect also works in situations where the runaway beam moves upwards and undergoes scraping-off on the wall.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Disruption thermal load mitigation with shattered pellet injection on the Joint European Torus (JET)

Disruption mitigation remains a critical, unresolved challenge for ITER. To aid in addressing this challenge, a shattered pellet injection (SPI) system was installed on JET and experiments conducted at a range of thermal energy fractions and stored energies in excess of 7 MJ. The primary goals of these experiments were to investigate the efficacy of the SPI on JET and the ability of the plasma to assimilate multiple pellets. Single pellet injections produced a saturation in total radiated energy (Wrad) with increasing injected neon content, suggesting total radiation of stored thermal energy. Further increases in injected neon quantities resulted in reduced cooling times and current quench (CQ) durations, indicating higher impurity assimilation. No significant variation in CQ duration or W rad was observed when varying the deuterium content at fixed neon quantities. Additionally, higher assimilation, inferred by shorter CQ durations, was measured when a mechanical punch was used to launch the pellets and this was attributed to a lower pellet velocity leading to higher solid content in the pellet plume and larger fragments penetrating deeper into the plasma. Radiation asymmetries averaged over the cooling time were inferred from Emis3D and ranged from 1.6 to 1.9. Asymmetries averaged over the entire disruption sequence were found to increase at higher thermal energy fractions. The radiated energy fractions decreased with increasing thermal energy fractions but this trend was eliminated when toroidal asymmetries were accounted for with Emis3D. Pure deuterium pellets were able to produce cooling times of up to 75 ms with a gradual loss in thermal stored energy of up to 80%. Experiments with multiple pellet injection indicated W rad can be increased through pellet superposition and density can be increased with an additional D2 injection without a reduction in W rad . KPRAD modelling accurately reproduced the cooling times and the CQ duration at high thermal energies. Assimilation estimates from KPRAD indicated CQ rates scale strongly whilst W rad scales weakly and saturates with assimilated neon content. Comparable W rad can be achieved with lower assimilated neon quantities as longer cooling times are attained. Thus reduced neon content can be preferential in a thermal load mitigation scheme as it may reduce radiation asymmetries and prevent flash melting.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Interpretation of electromagnetic modes in the sub-TAE frequency range in JET plasmas with elevated monotonic q-profiles

Recent JET deuterium experiments with an advanced tokamak scenario using an internal transport barrier (ITB) have been performed to clearly observe destabilized toroidicity-induced Alfvén eigenmodes (TAEs) by fast ions; interestingly, these also exhibit unstable electromagnetic (EM) perturbations in the sub-TAE frequency range. We identify such EM perturbations to be beta-induced ion temperature gradient (BTG) eigenmodes and not beta-induced Alfvén eigenmodes nor beta-induced Alfvén acoustic eigenmodes, which are often unstable in such high-beta plasmas with high-power neutral beam injection (NBI). The BTG modes are the most unstable modes due to the high thermal ion temperature gradient related to the ITB, high thermal ion temperature compared to thermal electron temperature (high T i /T⁠ e ), and a high ion beta regime. BTG mode experimental characteristics match the analytical theory, i.e., location in the vicinity of a rational magnetic surface with a low magnetic shear, mode frequency scaling with the ion diamagnetic frequency (⁠ω$^*_i$⁠), and a coupling among Alfvén and drift waves. We also perform linear gyrokinetic simulations with validated plasma profiles and equilibrium, and find a mode kinetically driven by thermal ions with similar characteristics as the experimental BTG modes.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Reduction of asymmetric wall force in JET and ITER disruptions including runaway electrons

It was shown that asymmetric vertical displacement event (AVDE) disruptions in JET and ITER do not produce a large asymmetric force on conducting structures surrounding the plasma, provided that the current quench (CQ) time is less than the resistive wall penetration time. This is verified with JET data. In ITER the CQ is expected to be comparable to the resistive wall penetration time, which gives a small wall force. It is shown that runaway electrons (REs) in JET do not produce a large wall force, and this is verified with JET data. This occurs if the RE current is about half of the initial plasma current. In ITER, the RE current might be comparable to the initial current, and REs might lengthen the CQ time sufficiently to produce a large wall force.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Overview of the JET preparation for deuterium–tritium operation with the ITER like-wall

For the past several years, the JET scientific programme (Pamela et al 2007 Fusion Eng. Des. 82 590) has been engaged in a multi-campaign effort, including experiments in D, H and T, leading up to 2020 and the first experiments with 50%/50% D–T mixtures since 1997 and the first ever D–T plasmas with the ITER mix of plasma-facing component materials. For this purpose, a concerted physics and technology programme was launched with a view to prepare the D–T campaign (DTE2). This paper addresses the key elements developed by the JET programme directly contributing to the D–T preparation. This intense preparation includes the review of the physics basis for the D–T operational scenarios, including the fusion power predictions through first principle and integrated modelling, and the impact of isotopes in the operation and physics of D–T plasmas (thermal and particle transport, high confinement mode (H-mode) access, Be and W erosion, fuel recovery, etc). This effort also requires improving several aspects of plasma operation for DTE2, such as real time control schemes, heat load control, disruption avoidance and a mitigation system (including the installation of a new shattered pellet injector), novel ion cyclotron resonance heating schemes (such as the three-ions scheme), new diagnostics (neutron camera and spectrometer, active Alfvèn eigenmode antennas, neutral gauges, radiation hard imaging systems...) and the calibration of the JET neutron diagnostics at 14 MeV for accurate fusion power measurement. The active preparation of JET for the 2020 D–T campaign provides an incomparable source of information and a basis for the future D–T operation of ITER, and it is also foreseen that a large number of key physics issues will be addressed in support of burning plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Assessment of the baseline scenario at q 95 ~ 3 for ITER

The International Tokamak Physics Activity topical group on integrated operational scenarios has compiled a database of stationary H-mode discharges at q 95 ~ 3 from AUG, C-Mod, DIII-D, JET and JT-60U, for both carbon wall and high-Z metal wall experiments with ~3300 entries. The analyses focus on discharges that are stationary for ≥5 thermal energy confinement times to evaluate the baseline scenario proposed for ITER at 15 MA for achieving its goals of Q = 10, fusion power of 500 MW at normalized pressure, β N = 1.8 and normalized confinement as predicted by the standard H-mode scaling, H 98y2 = 1. With the data restricted to stationary H-modes at q 95 ~ 3, the database shows significant variation of thermal energy confinement compared to the standard H-mode scaling (IPB98(y,2)) in dimensionless form. The data show similar scaling with normalized gyro-radius, but more favorable scaling towards lower collision frequency and more favorable scaling with plasma beta. Using all the engineering variables employed in IPB98(y,2), results in an overfit due to correlations among the data. Furthermore, there are significant residual trends in the confinement for plasma current, device size, loss power, and in particular for the plasma density. Significant differences between results obtained for devices with a carbon wall and high-Z metal wall are observed in the data, with data from carbon wall devices providing a larger operating space, encompassing ITER parameters or even exceeding them. H-modes in high-Z metal wall devices have, so-far, not accessed conditions at low collision frequencies, have lower normalized confinement (H 98y2 ~ 0.8–0.9) at low input power or beta, achieving H 98y2 ~ 1.0 only at input powers two times the L- to H-mode transition scaling predictions and at β N ~ 2.0. Hence, only the best H-modes with high-Z metal walls reach ITER baseline performance requirements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Scenario development for the observation of alpha-driven instabilities in JET DT plasmas

In DT plasmas, toroidal Alfvén eigenmodes (TAEs) can be made unstable by the alpha particles resulting from fusion reactions, and may induce a significant redistribution of fast ions. Recent experiments have been conducted in JET deuterium plasmas in order to prepare scenarios aimed at observing alpha-driven TAEs in a future JET DT campaign. Discharges at low density, large core temperatures associated with the presence of internal transport barriers and characterised by good energetic ion confinement have been performed. ICRH has been used in the hydrogen minority heating regime to probe the TAE stability. The consequent presence of MeV ions has resulted in the observation of TAEs in many instances. The impact of several key parameters on TAE stability could therefore be studied experimentally. Modeling taking into account NBI and ICRH fast ions shows good agreement with the measured neutron rates, and has allowed predictions for DT plasmas to be performed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Investigation into the formation of the scrape-off layer density shoulder in JET ITER-like wall L-mode and H-mode plasmas

The low temperature boundary layer plasma (scrape-off layer or SOL) between the hot core and the surrounding vessel determines the level of power loading, erosion and implantation of material surfaces, and thus the viability of tokamak-based fusion as an energy source. Here, this study explores mechanisms affecting the formation of flattened density profiles, so-called 'density shoulders', in the low-field side (LFS) SOL, which modify ion and neutral fluxes to surfaces—and subsequent erosion. There is evidence against local enhancement of ionization inducing shoulder formation. We find that increases in SOL parallel resistivity, Λ div (=[ L || ν ei Ω i ]/ c s Ω e ), postulated to lead to shoulder growth through changes in SOL turbulence characteristics, correlates with increases in SOL shoulder amplitude, A s , but only under a subset of conditions (D 2 -fuelled L-mode density scans with outer strike point on the horizontal target). Λ div fails to correlate with A s for cases of N 2 seeding or during sweeping of the strike point across the horizontal target. The limited correlation of Λ div and A s is also found for H-mode discharges. Thus, while it may be necessary for Λ div to be above a threshold of ~1 for shoulder formation and/or growth, another mechanism is required. More significantly, we find that in contrast to parallel resistivity, outer divertor recycling, as quantified by the total outer divertor Balmer D α emission, I – D α , does scale with A s where Λ div does and even where Λ div does not. Divertor recycling could lead to SOL density shoulder formation through: (a) reducing the parallel to the field flow (loss) of ions out of the SOL to the divertor; and (b) changes in radial electric fields which lead to E &#x00d7; B poloidal flows as well as potentially affecting SOL turbulence birth characteristics. Therefore, changes in divertor recycling may be the sole process involved in bringing about SOL density shoulders or it may be that it acts in tandem with parallel resistivity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Comparison of JET AVDE disruption data with M3D simulations and implications for ITER

Nonlinear 3D MHD asymmetric vertical displacement disruption simulations have been performed using JET equilibrium reconstruction initial data. There were several experimentally measured quantities compared with the simulation. These include vertical displacement, halo current, toroidal current asymmetry, and toroidal rotation. The experimental data and the simulations are in reasonable agreement. Also compared was the correlation of the toroidal current asymmetry and the vertical displacement asymmetry. The Noll relation between asymmetric wall force and vertical current moment is verified in the simulations. Also verified is the toroidal flux asymmetry. Though, JET is a good predictor of ITER disruption behavior, JET and ITER can be in different parameter regimes, and extrapolating from JET data can overestimate the ITER wall force.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Impact of divertor geometry on H-mode confinement in the JET metallic wall

Recent experiments with the ITER-like wall have demonstrated that changes in divertor strike point position are correlated with strong modification of the global energy confinement. The impact on energy confinement is observable both on the pedestal confinement and core normalised gradients. The corner configuration shows an increased core density gradient length and ion pressure indicating a better ion confinement. The study of neutral re-circulation indicates the neutral pressure in the main chamber varies inversely with the energy confinement and a correlation between the pedestal total pressure and the neutral pressure in the main chamber can be established. It does not appear that charge exchange losses nor momentum losses could explain this effect, but it may be that changes in edge electric potential are playing a role at the plasma edge. This study emphasizes the importance of the scrape-off layer (SOL) conditions on the pedestal and core confinement.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗