Engineering topics

Joh, D.

Publications and source records attributed to Joh, D..

8 records

NASA NTRS1992

Optical-precision alignment of diffraction grating mold in moire interferometry

A high-precision optical method is presented for aligning diffraction grating molds with the edges of specimens in moire interferometry. The alignment fixture is simple and convenient to operate. The conventional method of grating-mold alignment has a wide band of uncertainty in the range of error which is not compatible with the required precision of high-sensitivity moire interferometry. Following a description of the alignment technique, both the single-edge and parallel-edge guide bar optical alignment methods are introduced and compared.

Joh, D.↗

NASA NTRS1988

Deformations and strains in a thick adherend lap joint

Displacement fields in a thick adherend lap joint were measured by high-sensitivity moire interferometry. Contour maps of in-plane U and V displacements were obtained across adhesive and adherend surfaces. Loads ranged from a modest load to a near-failure load. Quantitative results are given for displacements and strains in the adhesive and along the adhesive/adherend boundary lines. The results show nearly constant shear strain in the adhesive, nonlinear strains as a function of load or average shear stress, and viscoelastic or time-dependent response. Longitudinal normal strains in the adhesive are nearly two orders of magnitude less than the shear strains. With its subwavelength displacement resolution and high spatial resolution, moire interferometry is especially well suited for deformation studies of adhesive joints.

Post, D.↗

NASA NTRS1986

Experimental study of a metal-matrix composite

A metal-matrix specimen was investigated using moire interferometry with 2400 lines/m (60,960 l/in.). The specimen was a 6-ply (0/ + or - 45)s boron-aluminum tensile coupon with a central slot. The unequal deformations in fibers and matrix were evident. Special attention was given to a plastic slip zone in the matrix. Normal and shear strains were calculated in the slip zone; the shear-strain concentration factor rose dramatically with the onset of plastic slip and continued to rise gradually with load to 95 percent of the failure load. The precipitous change from maximum tensile strain in one fiber to zero tensile strain in the neighboring fiber was accommodated by the very high shear strains of the matrix in the slip zone. Experimental considerations are discussed: shear strains are independent of rigid-body rotations; simplified strain calculations are justified; averaging across the narrow slip region and the influence of finite thickness of the specimen grating contribute to underestimation of peak strains.

Post, D.↗

NASA NTRS1985

Elastic-plastic deformation of a metal-matrix composite coupon with a center slot

A comprehensive experimental analysis of deformations of the surface of a metal-matrix specimen is reported. The specimen is a 6-ply 0 + or - 45 sub s boron-aluminum tensile coupon with a central slot. Moire interferometry is used for high-sensitivity whole-field measurements of in-plane displacements. Normal and shear strains are calculated from displacement gradients. Displacement fields are analyzed at various load levels from 15% to 95% of the failure load. Deformations of the boron fibers could be distinguished from those of the matrix. Highly localized plastic slip zones occur tangent to the ends of the slot. Shear strains and concurrent transverse compressive strains in the slip zones reach approximately 10% and 1%, respectively. Upon unloading, elastic recovery in surrounding regions causes a reverse plastic shear strain in the slip zone of about 4%. Longitudinal normal strains on the unslotted ligament peak at the slot boundary at about 1% strain. The strain concentration factor at the end of the slot decreases with load level and the advance of plasticity.

Post, D.↗

NASA NTRS1985

Shear-strain contours from moire interferometry

The development of whole-field contour maps of shear strains gamma (xy), derived from displacement fields obtained by moire interferometry with 2400 lines/mm, is described. The use of mechanical differentiation to obtain cross-derivatives of displacements and the use of graphical additive moire to sum the cross-derivatives are explained. Quantitative analysis in the small-strain domain is possible because of the high sensitivity of moire interferometry. The applicability of this technique is shown by the testing of a short epoxy beam under three-point bending.

Post, D.↗

NASA NTRS1985

Relative displacement measurements for two-body problems

While high-sensitivity moire interferometry is very effective for displacement measurements in continuous bodies, special difficulties arise with two-body problems. Fringes may become discontinuous at the boundary between the bodies and as a result the relative displacements cannot be extracted from the fringe patterns. In this work, flexible bridges are used between the bodies to provide a continuous path for fringe counting. The bridges are made of relatively low modulus material and have a low stiffness geometry, such that they deform under minimal load. The experimental methods used for obtaining relative displacement measurements in two-body problems are described for the two cases; dovetail joint in turbo-machinery, and thick adherend lap joint.

Post, D.↗

NASA NTRS1985

Shear strain anomalies in composite beam specimens by moire interferometry

Experimental analyses were performed for determination of in-plane deformations and shear strains in unidirectional and quasi-isotropic graphite-epoxy beams. Forty-eight-ply beams were subjected to five-point and three-point flexure. Whole-field measurements were recorded at load levels from about 20 percent to more than 90 percent of failure loads. Contour maps of U and W displacement fields were obtained by moire interferometry, using reference gratings of 2400 lines/mm. Clearly defined fringes with fringe orders exceeding 1000 were obtained. Whole-field contour maps of shear strains were obtained. Various anomalous effects were detected in the displacement fields. Their analysis indicated excess shear strains in resin-rich zones in regions of shear tractions; free-edge shear strains in quasi-isotropic specimens in regions of normal stresses, and shear stresses associated with cyclic shear compliances of quasi-isotropic laminates in regions of shear tractions. Their contributions could occur independently or in superposition. Qualitative analyses addressed questions of the effect of specimen overhang, nonlinearity, and characteristics of five-point and three-point flexure tests.

Post, D.↗

NASA NTRS1984

Deformation measurements of composite multi-span beam shear specimens by Moire interferometry

Experimental analyses were performed for determination of in plane deformations and shear strains in unidirectional and quasi-isotropic graphite-epoxy beams. Forty-eight ply beams were subjected to 5 point and 3 point flexure. Whole field measurements were recorded at load levels from about 20% to more than 90% of failure loads. Contour maps of U and W displacement fields were obtained by moire interferometry, using reference gratings of 2400 lines/mm. Clearly defined fringes with fringe orders exceeding 1000 were obtained. Whole field contour maps of shear strains were obtained by a method developed for these tests. Various anomalous effects were detected in the displacement fields. Their analysis indicated excess shear strains in resin rich zones in regions of shear tractions; free edge shear strains in quasi-isotropic specimens in regions of normal stresses; and shear stresses associated with cyclic shear compliances of quasi-isotropic plies in regions of shear tractions. Their contributions could occur independently or in superposition. Qualitative analyses addressed questions of relaxation; influence of contact stress distribution; specimen failure; effect of specimen overhang; nonlinearity; and qualities of 5 and 3 point flexure tests.

Post, D.↗