Search NASA⌕ Search

Engineering topics

Johannessen, Bernt

Publications and source records attributed to Johannessen, Bernt.

(Mg,Mn,Fe,Co,Ni)O: A rocksalt high-entropy oxide containing divalent Mn and Fe

High-entropy oxides (HEOs) have aroused growing interest due to fundamental questions relating to their structure formation, phase stability, and the interplay between configurational disorder and physical and chemical properties. Introducing Fe(ιι) and Mn(ιι) into a rocksalt HEO is considered challenging, as theoretical analysis suggests that they are unstable in this structure under ambient conditions. Here, we develop a bottom-up method for synthesizing Mn- and Fe-containing rocksalt HEO (FeO-HEO). We present a comprehensive investigation of its crystal structure and the random cation-site occupancy. We show the improved structural robustness of this FeO-HEO and verify the viability of an oxygen sublattice as a buffer layer. Compositional analysis reveals the valence and spin state of the iron species. We further report the antiferromagnetic order of this FeO-HEO below the transition temperature ~218 K and predict the conditions of phase stability of Mn- and Fe-containing HEOs. Our results provide fresh insights into the design and property tailoring of emerging classes of HEOs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Activation of Transition Metal (Fe, Co and Ni)-Oxide Nanoclusters by Nitrogen Defects in Carbon Nanotube for Selective CO 2 Reduction Reaction

The electrochemical carbon dioxide reduction reaction (CO2RR), which can produce value-added chemical feedstocks, is a proton-coupled-electron process with sluggish kinetics. Thus, highly efficient, cheap catalysts are urgently required. Transition metal oxides such as CoO x , FeO x , and NiO x are low-cost, low toxicity, and abundant materials for a wide range of electrochemical reactions, but are almost inert for CO 2 RR. Here, we report for the first time that nitrogen doped carbon nanotubes (N-CNT) have a surprising activation effect on the activity and selectivity of transition metal-oxide (MO x where M = Fe, Ni, and Co) nanoclusters for CO 2 RR. MO x supported on N-CNT, MOx/N-CNT, achieves a CO yield of 2.6–2.8 mmol cm -2 min -1 at an overpotential of -0.55V, which is two orders of magnitude higher than MO x supported on acid treated CNTs (MOx/O-CNT) and four times higher than pristine N-CNT. The faraday efficiency for electrochemical CO 2 -to-CO conversion is as high as 90.3% at overpotential of 0.44V. Both in-situ XAS measurements and DFT calculations disclose that MO x nanoclusters can be hydrated in CO 2 saturated KHCO 3 , and the N defects of N-CNT effectively stabilize these metal hydroxyl species under carbon dioxide reduction reaction conditions, which can split the water molecules and provide local protons to inhibit the poisoning of active sites under carbon dioxide reduction reaction conditions.

36 MATERIALS SCIENCE↗

Designed Iron Single Atom Catalysts for Highly Efficient Oxygen Reduction Reaction in Alkaline and Acid Media

Abstract Single atom catalysts (SACs) have attracted much attentions due to their advantages of high catalysis efficiency and excellent selectivity. However, for industrial applications, synthesis of SACs in large and practical quantities is very important. The challenge is to develop synthesis methods with controllability and scalability. Herein, a well‐characterized and scalable method is demonstrated to synthesize atomically dispersed iron atoms coordinated with nitrogen on graphene, SAFe @ NG, with high atomic loading (≈4.6 wt%) through a one‐pot pyrolysis process. The method is scalable for the fabrication of Fe SACs with high quantities. The Fe–N–G catalyst exhibits high intrinsic oxygen reduction reaction (ORR) performance, reaching half potential of 0.876 and 0.702 V in alkaline and acidic solutions, respectively, with excellent microstructure stability. Furthermore, the density functional theory (DFT) simulation confirms that the Fe atoms in coordination with four nitrogen atoms, FeN4, in graphene is the active center for the 4‐electron ORR process. This work demonstrates an efficient design pathway for single atom catalysts as highly active and stable electrocatalysts for high‐performance ORR applications.

Zhao, Shiyong↗

Controlled One‐pot Synthesis of Nickel Single Atoms Embedded in Carbon Nanotube and Graphene Supports with High Loading

Abstract Single‐atom catalysts (SACs) have attracted much attentions due to the advantages of high catalysis efficiency and selectivity. However, the controllable and efficient synthesis of SACs remains a significant challenge. Herein, we report a controlled one‐pot synthesis of nickel single atoms embedded on nitrogen‐doped carbon nanotubes (NiSA−N−CNT) and nitrogen‐doped graphene (NiSA−N−G). The formation of NiSA−N−CNT is due to the solid‐to‐solid rolling up mechanism during the high temperature pyrolysis at 800 °C from the stacked and layered Ni‐doped g‐C 3 N 4 , g‐C 3 N 4 −Ni structure to a tubular CNT structure. Addition of citric acid introduces an amorphous carbon source on the layered g‐C 3 N 4 −Ni and after annealing at the same temperature of 800 °C, instead of formation of NiSA−N−CNT, Ni single atoms embedded in planar graphene type supports, NiSA−N−G were obtained. The density functional theory (DFT) calculation indicates the introduction of amorphous carbon source substantially reduces the structure fluctuation or curvature of layered g‐C 3 N 4 ‐Ni intermediate products, thus interrupting the solid‐to‐solid rolling process and leading to the formation of planar graphene type supports for Ni single atoms. The as‐synthesized NiSA−N−G with Ni atomic loading of ∼6 wt% catalysts shows a better activity and stability for the CO 2 reduction reaction (CO 2 RR) than NiSA−N−CNT with Ni atomic loading of ∼15 wt% due to the open and exposed Ni single atom active sites in NiSA−N−G. This study demonstrates for the first time the feasibility in the control of the microstructure of carbon supports in the synthesis of SACs.

Zhao, Shiyong↗

Theoretical Calculation Guided Design of Single-Atom Catalysts toward Fast Kinetic and Long-Life Li–S Batteries

Lithium–sulfur (Li–S) batteries are enticing next-generation energy storage technologies due to their high theoretical energy density, environmental friendliness, and low cost. Yet, low conductivity of sulfur species, dissolution of polysulfides, poor conversion from sulfur reduction, and lithium sulfide (Li 2 S) oxidation reactions during discharge–charge processes hinder their practical applications. Herein, under the guidance of density functional theory calculations, we have successfully synthesized large-scale single atom vanadium catalysts seeded on graphene to achieve high sulfur content (80 wt % sulfur), fast kinetic (a capacity of 645 mAh g –1 at 3 C rate), and long-life Li–S batteries. Both forward (sulfur reduction) and reverse reactions (Li 2 S oxidation) are significantly improved by the single atom catalysts. This finding is confirmed by experimental results and consistent with theoretical calculations. The ability of single metal atoms to effectively trap the dissolved lithium polysulfides (LiPSs) and catalytically convert the LiPSs/Li 2 S during cycling significantly improved sulfur utilization, rate capability, and cycling life. Our work demonstrates an efficient design pathway for single atom catalysts and offers solutions for the development of high energy/power density Li–S batteries.

25 ENERGY STORAGE↗

A Universal Seeding Strategy to Synthesize Single Atom Catalysts on 2D Materials for Electrocatalytic Applications

Abstract Single‐atom catalysts (SACs) are attracting significant attention due to their exceptional catalytic performance and stability. However, the controllable, scalable, and efficient synthesis of SACs remains a significant challenge. Herein, a new and versatile seeding approach is reported to synthesize SACs supported on different 2D materials such as graphene, boron nitride (BN), and molybdenum disulfide (MoS 2 ). This method is demonstrated on the synthesis of Ni, Co, Fe, Cu, Ag, Pd single atoms as well as binary atoms of Ni and Cu codoped on 2D support materials with the mass loading of single atoms in the range of 2.8–7.9 wt%. In particular, the applicability of the new seeding strategy in electrocatalysis is demonstrate on nickel SACs supported on graphene oxide (SANi‐GO), exhibiting excellent catalytic performance for electrochemical CO 2 reduction reaction with a turnover frequency of 325.9 h −1 at a low overpotential of 0.63 V and high selectivity of 96.5% for CO production. The facile, controllable, and scalable nature of this approach in the synthesis of SACs is expected to open new research avenues for the practical applications of SACs.

Zhao, Shiyong↗

Iron Single Atoms on Graphene as Nonprecious Metal Catalysts for High‐Temperature Polymer Electrolyte Membrane Fuel Cells

Abstract Iron single atom catalysts (Fe SACs) are the best‐known nonprecious metal (NPM) catalysts for the oxygen reduction reaction (ORR) of polymer electrolyte membrane fuel cells (PEMFCs), but their practical application has been constrained by the low Fe SACs loading (<2 wt%). Here, a one‐pot pyrolysis method is reported for the synthesis of iron single atoms on graphene (FeSA‐G) with a high Fe SAC loading of ≈7.7 ± 1.3 wt%. The as‐synthesized FeSA‐G shows an onset potential of 0.950 V and a half‐wave potential of 0.804 V in acid electrolyte for the ORR, similar to that of Pt/C catalysts but with a much higher stability and higher phosphate anion tolerance. High temperature SiO 2 nanoparticle‐doped phosphoric acid/polybenzimidazole (PA/PBI/SiO 2 ) composite membrane cells utilizing a FeSA‐G cathode with Fe SAC loading of 0.3 mg cm −2 delivers a peak power density of 325 mW cm −2 at 230 °C, better than 313 mW cm −2 obtained on the cell with a Pt/C cathode at a Pt loading of 1 mg cm −2 . The cell with FeSA‐G cathode exhibits superior stability at 230 °C, as compared to that with Pt/C cathode. Our results provide a new approach to developing practical NPM catalysts to replace Pt‐based catalysts for fuel cells.

25 ENERGY STORAGE↗

One-Pot Pyrolysis Method to Fabricate Carbon Nanotube Supported Ni Single-Atom Catalysts with Ultrahigh Loading

The practical application of single atom catalysts (SACs) is constrained by the low achievable loading of single metal atoms. In this work, nickel SACs stabilized on a nitrogen-doped carbon nanotube structure (NiSA-N-CNT) with ultrahigh Ni atomic loading up to 20.3 wt % have been successfully synthesized using a new one-pot pyrolysis method employing Ni acetylacetonate (Ni(acac) 2 ) and dicyandiamide (DCD) as precursors. The yield and formation of NiSA-N-CNT depends strongly on the Ni(acac) 2 /DCD ratio and annealing temperature. Pyrolysis at 350 and 650 °C led to the formation of Ni single atom dispersed melem and graphitic carbon nitride (Ni-melem and Ni-g-C 3 N 4 ). Transition from a stacked and layered Ni-g-C 3 N 4 structure to a bamboo-shaped tubular NiSA-N-CNT structure most likely occurs via a solid-to-solid curling or rolling-up mechanism, thermally activated at temperatures of 700–900 °C. Extended X-ray absorption fine structure (EXAFS) experiments and simulations show that Ni single atoms are stabilized in the N-CNT structure through nitrogen coordination, forming a structure with four nearest N coordination shell surrounded by two carbon shells, Ni–N 4 . The NiSA-N-CNT catalysts show an excellent activity and selectivity for the electrochemical reduction of CO 2 , achieving a turnover frequency (TOF) of 11.7 s–1 at -0.55 V (vs RHE), but a low activity for the O 2 reduction and O 2 evolution reactions, as compared to Ni nanoparticles supported on N-CNTs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Atomically Dispersed Transition Metals on Carbon Nanotubes with Ultrahigh Loading for Selective Electrochemical Carbon Dioxide Reduction

Single-atom catalysts (SACs) are the smallest entities for catalytic reactions with projected high atomic efficiency, superior activity, and selectivity; however, practical applications of SACs suffer from a very low metal loading of 1–2 wt%. Here, a class of SACs based on atomically dispersed transition metals on nitrogen-doped carbon nanotubes (MSA-N-CNTs, where M = Ni, Co, NiCo, CoFe, and NiPt) is synthesized with an extraordinarily high metal loading, e.g., 20 wt% in the case of NiSA-N-CNTs, using a new multistep pyrolysis process. Among these materials, NiSA-N-CNTs show an excellent selectivity and activity for the electrochemical reduction of CO 2 to CO, achieving a turnover frequency (TOF) of 11.7 s -1 at -0.55 V (vs reversible hydrogen electrode (RHE)), two orders of magnitude higher than Ni nanoparticles supported on CNTs.

36 MATERIALS SCIENCE↗

(Pentamethylcyclopentadienato)rhodium complexes for delivery of the curcumin anticancer drug [Rhodium pentamethylcyclopentadienato complexes for delivery of the curcumin anti-cancer drug]

[RhIII(*Cp)Cl(X,Y)] n+ complexes {X, Y = Cl, PTA, n = 0 (2); X, Y = en, n = 1 (3, Cl– salt; 4, PF 6 – salt); X, Y = acac, n = 0 (5); X, Y = cur, n = 0 (6), where *Cp = pentamethylcyclopentadienato, curH = curcumin; PTA = 1,3,5-triaza-7-phosphatricyclo[3.3.1.1]decane; en = 1,2-ethanediamine; acac = acetylacetonato = 2,4-pentanedionato(1–)} were synthesized from [Rh(*Cp)(µ-Cl)Cl] 2 (1). While 2–5 were inactive against human epithelial A549 lung-cancer cells in assays of cytotoxicity, and antimetastatic and proapoptotic behaviors, 6 had a cytotoxic activity similar to that of curH over 72 h, but at 24 h in real-time cell migration assays, it was less active, showing slow release of curH. All complexes underwent ligand-exchange reactions with biomolecules and cells within the timeframes of the assays (X-ray absorption spectroscopy). Intracellular elemental distributions (X-ray fluorescence microscopy) showed that 6 effectively delivered curH to cells, where it was released. Other elemental distributions and caspase activities were consistent with preapoptotic activities. As such, 6 is a promising delivery agent for bioactive ligands, such as curH. However, pure curcumin itself showed a previously unrecognized ability to promote migration of A549 cells at subtoxic concentrations in the presence of endothelial growth factor, which may be a concern for its widespread use as a nutritional supplement and as a potential drug. As a result, this aspect warrants further research.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structural studies of the rhombohedral and orthorhombic monouranates: CaUO{sub 4}, α-SrUO{sub 4}, β-SrUO{sub 4} and BaUO{sub 4}

The structures of some AUO{sub 4} (A=Ca, Sr, or Ba) oxides have been determined using a combination of neutron and synchrotron X-ray diffraction, supported by X-ray absorption spectroscopic measurements at the U L{sub 3}-edge. The smaller Ca cation favours a rhombohedral AUO{sub 4} structure with 8-coordinate UO{sub 8} moieties whilst an orthorhombic structure based on UO{sub 6} groups is found for BaUO{sub 4}. Both the rhombohedral and orthorhombic structures can be stabilised for SrUO{sub 4}. The structural studies suggest that the bonding requirements of the A site cation play a significant role in determining which structure is favoured. In the rhombohedral structure, Bond Valence Sums demonstrate the A site is invariably overbonded, which, in the case of rhombohedral α-SrUO{sub 4}, is compensated for by the formation of vacancies in the oxygen sub-lattice. The uranium cation, with its flexible oxidation state, is able to accommodate this by inducing vacancies along its equatorial coordination site as demonstrated by neutron powder diffraction. - Graphical abstract: Diffraction studies of AUO{sub 4} (A = Ca, Sr, or Ba) oxides reveal the importance of the bonding requirements of the A site cation in determining whether the structure is rhombohedral or orthorhombic. - Highlights: • Structures of AUO{sub 4} ( A = Ca Sr, Ba) refined against X-ray and Neutron diffraction. • The alkali cations size has a dramatic effect on the crystal structure. • Smaller cations favouring a rhombohedral structure. • Oxygen vacancies to stabilise the rhombohedral structure in SrUO{sub 4}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterizing structural and vibrational properties of nanoparticles embedded in silica with XAS, SAXS and auxiliary techniques

Synchrotron-based techniques were combined with conventional analysis methods to probe in detail the structural and vibrational properties of nanoparticles grown in a silica matrix by ion implantation and thermal annealing, as well as the evolution of such properties as a function of nanoparticle size. This original approach was successfully applied for several elemental nanoparticles (Au, Co, Cu, Ge, Pt) and the outcomes for Ge are reported here, illustrating the power of this combined methodology. The thorough analysis of XANES, EXAFS, SAXS, TEM and Raman data for Ge nanoparticles with mean diameters between 4 and 9 nm revealed that the peculiar properties of embedded Ge nanoparticles, like the existence of amorphous Ge layers between the silica matrix and the crystalline nanoparticle core, are strongly dependent on particle size and mainly governed by the variation in the surface area-to-volume ratio. Such detailed information provides valuable input for the efficient planning of technological applications.

36 MATERIALS SCIENCE↗

Phase and valence transitions in Ba{sub 2}LnSn{sub x}Nb{sub 1-x}O{sub 6-{delta}}

The structures of compounds in the perovskite series Ba{sub 2}LnSn{sub x}Nb{sub 1-x}O{sub 6-{delta}} (Ln=Pr and Tb and x=0, 0.1, 0.2, ..., 1.0) have been examined using synchrotron X-ray and neutron diffraction. It was found that niobate members of both series feature full B-site cation ordering but that this order is lost with increasing x. X-ray absorption near-edge structure (XANES) and near-infrared spectroscopies indicate that the oxidation state of the lanthanide cations gradually changes from Ln{sup 3+} to Ln{sup 4+} with increased Sn{sup 4+} doping. This is believed to be the cause of the loss of B-site ordering. Least squares analysis of the XANES spectra suggests that the rate of the transformation of Ln{sup 3+} cations to the tetravalent state is such that the Pr series contains no oxygen vacancies while the Tb series may contain a very small amount of vacancies, with {delta}{approx}0.02. - Graphical abstract: The series Ba{sub 2}LnSn{sub x}Nb{sub 1-x}O{sub 6-{delta}} (Ln=Pr and Tb) has been investigated using powder diffraction and spectroscopic techniques. Similarly to the analogous Sb{sup 5+} containing compounds it was found that Sn{sup 4+} doping leads to the gradual oxidation of the Ln{sup 3+} cations to the Ln{sup 4+} state. Quantitative analysis of the Ln L{sub III}-edge absorption spectra indicates that few or no oxygen vacancies are present.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗