Engineering topics

Johnson, W. G., Jr.

Publications and source records attributed to Johnson, W. G., Jr..

16 records

NASA NTRS1992

Further buffeting tests in a cryogenic wind tunnel

Further measurements of buffeting, using wing-root strain gauges, were made in the NASA Langley 0.3 m Cryogenic Wind Tunnel to refine techniques which will be used in larger cryogenic facilities such as the United States National Transonic Facility (NTF) and European Transonic Wind Tunnel (ETW). The questions addressed included the relative importance of variations in frequency parameter and Reynolds number, the choice of model material (considering both stiffness and damping) and the effects of static aeroelastic distortion. The main series of tests was made on half models of slender 65 deg delta wings with a sharp leading edge. The three delta wings had the same planform but widely different bending stiffness and frequencies (obtained by varying both the material and the thickness of the wings). It was known that the flow on this configuration would be insensitive to variations in Reynold number. Additional tests were made on one unswept half-wing of aspect ratio 1.5 with an NPL 9510 aerofoil section, known to be sensitive to variations in Reynolds number at transonic speeds. For brevity the test Mach numbers were restricted to M = 0.21 and 0.35 for the delta wings and to M = 0.30 for the unswept wing.

Mabey, D. G.↗

NASA NTRS1986

A summary of Reynolds number effects on some recent tests in the Langley 0.3-meter transonic cryogenic tunnel

Reynolds number effects noted from selected test programs conducted in the Langley 0.3-Meter Transonic Cryogenic Tunnel (0.3-m TCT) are discussed. The tests, which cover a unit Reynolds number range from about 2.0 to 80.0 million per foot, summarize effects of Reynolds number on: (1) aerodynamic data from a supercritical airfoil, (2) results from several wall interference correction techniques, and (3) results obtained from advanced, cryogenic tests techniques. The test techniques include: (1) use of a cryogenic sidewall boundary layer removal system, (2) detailed pressure and hot wire measurements to determine test section flow quality, and (3) use of a new hot film system suitable for transition detection in a cryogenic wind tunnel. The results indicate that Reynolds number effects appear most significant when boundary layer transition effects are present and at high lift conditions when boundary layer separation exists on both the model and the tunnel sidewall.

Johnson, C. B.↗

NASA NTRS1985

Pressure distributions from high Reynolds number tests of a Boeing BAC 1 airfoil in the Langley 0.3-meter transonic cryogenic tunnel

A wind-tunnel investigation designed to test a Boeing advanced-technology airfoil from low to flight-equivalent Reynolds numbers has been completed in the Langley 0.3-Meter Transonic Cryogenic Tunnel. This investigation represents the first in a series of NASA/U.S. industry two-dimensional airfoil studies to be completed in the Advanced Technology Airfoil Test program. Test temperature was varied from ambient to about 100 K at pressures ranging from about 1.2 to 6.0 atm. Mach number was varied from about 0.40 to 0.80. These variables provided a Reynolds number (based on airfoil chord) range from 4.4 X 10 to the 6th power to 50.0 X 10 to the 6th power. All the test objectives were met. The pressure data are presented without analysis in plotted and tabulated formats for use in conjunction with the aerodynamic coefficient data published as NASA TM-81922. At the time of the test, these pressure data were considered proprietary and have only recently been made available by Boeing for general release. Data are included which demonstrate the effects of fixed transition. Also included are remarks on the model design, the model structural integrity, and the overall test experience.

Johnson, W. G., Jr.↗

NASA NTRS1985

Pressure distribution from high Reynolds number tests of a NASA SC(3)-0712(B) airfoil in the Langley 0.3-meter transonic cryogenic tunnel

A wind tunnel investigation of a NASA 12-percent-thick, advanced-technology supercritical airfoil was conducted in the Langley 0.3-Meter Transonic Cryogenic Tunnel (TCT). This investigation represents another in the series of NASA/U.S. industry two-dimensional airfoil studies to be completed in the Advanced Technology Airfoil Tests program. Test temperature was varied from 220 K to 96 K at pressures ranging from 1.2 to 4.3 atm. Mach number was varied from 0.50 to 0.80. This investigation was designed to: (1) test a NASA advanced-technology airfoil from low to flight equivalent Reynolds numbers, (2) provide experience in cryogenic wind-tunnel model design and testing techniques, and (3) demonstrate the suitability of the 0.3-m TCT as an airfoil test facility. All the test objectives were met. The pressure data are presented without analysis in tabulated format and as plots of pressure coefficient versus position on the airfoil. This report was prepared for use in conjunction with the aerodynamic coefficient data published in NASA-TM-86371. Data are included which demonstrate the effects of fixed transition. Also included are remarks on the model design and fabrication.

Johnson, W. G., Jr.↗

NASA NTRS1985

High Reynolds number tests of a NASA SC(3)-0712(B) airfoil in the Langley 0.3-meter transonic cryogenic tunnel

A wind tunnel investigation of a NASA 12-percent-thick, advanced-technology supercritical airfoil was conducted in the Langley 0.3-Meter Transonic Cryogenic Tunnel (TCT). This investigation represents another in the series of NASA/U.S. industry two-dimensional airfoil studies to be completed in the Advanced Technology Airfoil Tests program. Test temperature was varied from 220 K to 96 K at pressures ranging from 1.2 to 4.3 atm. Mach number was varied from 0.60 to 0.80. These variables provided a Reynolds number range from 4,400,000 to 40,000,000 based on a 15.24-cm (6.0-in.) airfoil chord. This investigation was designed to test a NASA advanced-technology airfoil from low to flight-equivalent Reynolds numbers, provide experience in cryogenic wind tunnel model design and testing techniques, and demonstrate the suitability of the 0.3-m TCT as an airfoil test facility. The aerodynamic results are presented as integrated force and moment coefficients and pressure distributions. Data are included which demonstrate the effects of fixed transition, Mach number, and Reynolds number on the aerodynamic characteristics. Also included are remarks on the model design, the model structural integrity, and the overall test experience.

Johnson, W. G., Jr.↗

NASA NTRS1984

Data from tests of a R4 airfoil in the Langley 0.3-meter transonic cryogenic tunnel

Aerodynamic data for the DFVLR R4 airfoil are presented in both graphic and tabular form. The R4 was tested in the Langley 0.3-Meter Transonic Cryogenic Tunnel (TCT) at Mach number from 0.60 to 0.78 at angles of attack from -2.0 to 8.0 degrees. The airfoil was tested at Reynolds numbers of 4, 6, 10, 15, 30, and 40 million based on the 152.32 mm chord.

Jenkins, R. V.↗

NASA NTRS1983

Aerodynamic force measurements with a strain-gage balance in a cryogenic wind tunnel

Aerodynamic force measurements on a generalized 75 deg delta wing model with sharp leading edges were made with a three component internal strain gage balance in a cryogenic wind tunnel at stagnation temperatures of 300 K, 200 K, and 110 K. The feasibility of using a strain gage balance without thermal control in a cryogenic environment as well as the use of electrical resistance heaters, an insulator between the model and the balance, and a convection shield on the balance was investigated. Force and moment data on the delta wing model as measured by the balance are compared at the different temperatures while holding constant either the Reynolds number or the tunnel stagnation pressure. Tests were made at Mach numbers of 0.3 and 0.5 and at angles of attack up to 29 deg. The results indicate that it is feasible to acquire accurate force and moment data while operating at steady state thermal conditions in a cryogenic wind tunnel, either with or without electrical heaters on the balance. Within the limits of the balance accuracy, there were no apparent Reynolds number effects on the aerodynamic results for the delta wind model.

Boyden, R. P.↗

NASA NTRS1982

Results of buffet tests in a cryogenic wind tunnel

Buffet tests on two semispan wing models with different leading edge sweep show that it is feasibile to use the standard dynamic wing root bending moment technique in a cryogenic wind tunnel. One model was a slender 65 deg swept delta wing with sharp leading edges. The other model was an unswept wing of aspect ratio 1.5 with a British NPL 9510 airfoil section. The results for the 65 deg swept delta wing indicate the importance of matching the reduced frequency parameter in model tests for planforms which are sensitive to reduced frequency parameter if quantitative buffet measurements are required. The unique ability of a pressurized cryogenic wind tunnel to separate the effects of Reynolds number and of static aeroelastic distortion by variations in the tunnel stagnation temperature and pressure were demonstrated.

Boyden, R. P.↗

NASA NTRS1982

High Reynolds number tests of a Boeing BAC I airfoil in the Langley 0.3-meter transonic cryogenic tunnel

A wind tunnel investigation of an advanced-technology airfoil was conducted in the Langley 0.3-Meter Transonic Cryogenic Tunnel (TCT). This investigation represents the first in a series of NASA/U.X. industry two dimensional airfoil studies to be completed in the Advanced Technology Airfoil Test program. Test temperature was varied from ambient to about 100 K at pressures ranging from about 1.2 to 6.0 atm. Mach number was varied from about 0.40 to 0.80. These variables provided a Reynolds number (based on airfoil chord) range from about .0000044 to .00005. This investigation was specifically designed to: (1) test a Boeing advanced airfoil from low to flight-equivalent Reynolds numbers; (2) provide the industry participant (Boeing) with experience in cryogenic wind-tunnel model design and testing techniques; and (3) demonstrate the suitability of the 0.3-m TCT as an airfoil test facility. All the objectives of the cooperative test were met. Data are included which demonstrate the effects of fixed transition, Mach number, and Reynolds number on the aerodynamic characteristics of the airfoil. Also included are remarks on the model design, the model structural integrity, and the overall test experience.

Johnson, W. G., Jr.↗

NASA NTRS1981

Preliminary results of buffet tests in a cryogenic wind tunnel

Buffet tests of two wings with different leading-edge sweep show that it is feasible to use the standards wing root bending moment technique in a cryogenic wing tunnel. The results for the 65 deg sweep delta wing indicate the importance of matching the reduced frequency parameter in model tests for planforms which are sensitive to reduced frequency parameter if quantitative buffet measurements are required. The unique ability of a pressurized cryogenic wind tunnel to separate the effects of Reynolds number and of aeroelastic distortion by variations in the tunnel stagnation temperature and pressure was demonstrated.

Boyden, R. P.↗

NASA NTRS1979

Aerodynamic characteristics at low Reynolds numbers of several heat-exchanger configurations for wind-tunnel use

In response to design requirements of the National Transonic Facility, aerodynamic tests were conducted to determine the pressure-drop, flow-uniformity, and turbulence characteristics of various heat-exchanger configurations as a function of Reynolds number. Data were obtained in air with an indraft flow apparatus operated at ambient temperature and pressure. The unit Reynolds number of the tests varied from about 0.06 x 10 to 6th power to about 1.3 x 10 to 6th power per meter. The test models were designed to represent segments of full-scale tube bundles and included bundles of round tubes with plate fins in both staggered and inline tube arrays, round tubes with spiral fins, elliptical tubes with plate fins, and an inline grouping of tubes with segmented fins.

Johnson, W. G., Jr.↗

NASA NTRS1976

Pressure distributions on a rectangular aspect-ratio-6, slotted supercritical airfoil wing with externally blown flaps

An investigation was made in the 5.18 m (17 ft) test section of the Langley 300 MPH 7 by 10 foot tunnel on a rectangular, aspect ratio 6 wing which had a slotted supercritical airfoil section and externally blown flaps. The 13 percent thick wing was fitted with two high lift flap systems: single slotted and double slotted. The designations single slotted and double slotted do not include the slot which exists near the trailing edge of the basic slotted supercritical airfoil. Tests were made over an angle of attack range of -6 deg to 20 deg and a thrust-coefficient range up to 1.94 for a free-stream dynamic pressure of 526.7 Pa (11.0 lb/sq ft). The results of the investigation are presented as curves and tabulations of the chordwise pressure distributions at the midsemispan station for the wing and each flap element.

Johnson, W. G., Jr.↗

NASA NTRS1976

Some measurements of an EBF powered-lift wake

Results from a wind tunnel investigation in which velocity vector measurements were obtained in the near wake of an externally blown flap powered lift configuration were analyzed. These measurements were used to develop spanwise distributions for the momentum strength and location of the engine exhaust stream tube with the results used as input parameters to one jet flap analytical method. It is shown that a comparison of the momentum coefficients obtained from forward speed wake surveys with the predicted values from static force data results in a good correlation, which verifies the use of the flap thrust recovery factor as a means of predicting the momentum strength at the flap trailing edge. Also, when wake survey distributions of momentum strength and direction are used as input parameters to one analytical jet flap method, the results show reasonable agreement between the experimental data and analytical results.

Johnson, W. G., Jr.↗

NASA NTRS1975

Aerodynamic characteristics of a powered, externally blown flap STOL transport model with two engine simulator sizes

The low-speed aerodynamic characteristics are investigated of a general research model - a swept-wing, jet-powered STOL transport with externally blown flaps. The model was tested with four-engine simulators mounted on pylons under the 9.3-percent-thick supercritical airfoil wing. Two sets of air ejectors were used to provide data with large and small engines. Tests were conducted in the Langley V/STOL tunnel over an angle-of-attack range of -4 deg to 22 deg and a thrust-coefficient range from 0 to approximately 4. The effects are described of power, wing leading-edge slat configuration, T-tail and low horizontal-tail positions, and double-slotted flap deflection. Additional untrimmed and trimmed engine-out data and tail-body data are included.

Johnson, W. G., Jr.↗

NASA NTRS1974

A wind tunnel investigation of the wake near the trailing edge of a deflected externally blown flap

The model tested was a general research model of a swept-wing, jet-powered STOL transport with externally blown flaps. The model was tested with four engine simulators mounted on pylons under the wing. Tests were conducted in the V/STOL tunnel over an angle of attack range of 0 deg to 16 deg and a thrust coefficient range from 0 to approximately 4 at a Reynolds number of 0.461 x 1 million based on the wing reference chord. The results of this investigation are presented primarily as plots of the individual velocity vectors obtained from the wake survey. These data are used to extend an earlier analysis to isolate the effects of the engine thrust on the behavior of the flow at the flap trailing edge. Results of a comparison with a jet-flap theory are also shown.

Johnson, W. G., Jr.↗

NASA NTRS1972

Aerodynamic and performance characteristics of externally blown flap configurations

The application of externally blown flaps for improving the performance of short takeoff aircraft is discussed. The characteristics of externally blown flap powered lift are examined. A method for predicting the aerodynamic performance of a particular externally blown flap configuration is presented. The following specific effects are analyzed: (1) induced aerodynamics, (2) static turning, (3) flap span and deflection, and (4) engine size and chord flap.

Johnson, W. G., Jr.↗