Search NASA⌕ Search

Engineering topics

Jonathan Gleeson

Publications and source records attributed to Jonathan Gleeson.

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2021

Insitu Lunar Launch & Landing Pad Construction w/ Regolith and Thermoset Polymers

This CIF project is an extension of materials developed under a previous NASA Innovative Advanced Concepts (NIAC) project titled “Regolith Derived Heat Shield for Planetary Body Entry and Descent Systems with In-Situ Fabrication” by M. Hogue et al. (2012). Launch and landing pads are necessary to mitigate risks to lander/ascent vehicles, surface assets, and orbital assets from rocket plume ejected regolith. At this time, all launching and landing on the lunar surface will be on unprepared surface sites. Though this has been a successful approach for Apollo and other uncrewed missions, significant risks exist for the Artemis Program due to the increased thrust of the vehicles, presence of co-located assets, and potential surface level requirements for tall vehicles. This project developed a thermoset polymer–regolith composite material for use as a launch and landing pad. Test articles were prepared at 20% and 11% polymer mass percent (wt%) and tested under hot fire conditions that simulated large vehicle lunar launch/landing conditions. A minimum polymer wt% of 9% was achieved and both samples successfully mitigated regolith ejecta from plume effects. A concept for emplacing launch/landing pads was successfully tested in laboratory environments using a screw and barrel approach to mixing, conveying and depositing materials. It is recommended that materials and systems be developed to TRL 6 for a small-scale lunar demonstration of emplacement of a launch/landing pad via a Commercial Lunar Payload Services (CLPS) mission to support the Artemis Program.

Nathan Gelino↗
NASA NTRS2021

Customized Science Carrier Modules and Accessories Developed for Microgravity Simulation Devices

Because the access to the true weightless environment of the ISS and other Low Earth Orbit (LEO) vehicles is limited and cost prohibitive, the need for ground-based microgravity simulation analogs to bridge the gravity continuum gap between 1g gravity and costly space flight studies with true weightlessness was realized. As such, the Microgravity Simulation Support Facility (MSSF) was established at NASA John F. Kennedy Space Center (KSC) to fulfill the need of the scientific community. Our facility provides the US science community with a focal point in the field of gravitational research by granting access to an array of two-dimensional(2D) and three-dimensional (3D)clinostats, and Random Positioning Machine (RPM) platforms developed by teams throughout the world. The availability of these capabilities will allow further understanding the role of altered gravity vectors from “functional weightlessness”, partial gravity conditions (1 x 10-3to 0.9g, and Moon and Mars ‘g vectors), to hypergravity (up to3g) on biological processes. We have designed and 3D printed a variety of specialized attachments(and associated “static control” hardware)to allow researchers to mount their samples onto these microgravity simulation devices to meet their unique science requirements. A summary of each attachment module will be presented below. Note: All software or code information should be requested to the author Ye Zhang, Kennedy Space Center ye.zhang-1@nasa.gov

Ye Zhang↗
NASA NTRS2021

Spectrum – An Instrument for Multispectral Biological Fluorescence Imaging on the International Space Station

Spectrum is a compact instrument for fluorescent imaging of biological specimens in microgravity and capable of operating within the constraints of an EXPRESS Rack on the International Space Station (ISS). The Spectrum Flight Unit (SFU) was launched to ISSin November 2019 and is available for science investigations as a general instrument. A duplicate Engineering Development Unit (EDU) is available at NASA Kennedy Space Center (KSC). Science Verification Testing (SVT) performed at KSCdemonstrated all required functions including five (5) fluorescence excitation wavelengths, growth lighting, environmental controls and monitoring, and high-resolution imaging using a 71 Megapixel camera with flat field lens. The design features key Orbital Replaceable Unit (ORU) components, which may be adapted or changed by future investigators for tailored science experiments.

Bradley Burns↗
NASA NTRSDate not supplied

In-situ Lunar Launch and Landing Pad Construction with Regolith-Thermoset Polymer Composite Materials

Lunar launch and landing pads are necessary to mitigate risks to lander/ascent vehicles and surrounding surface assets from rocket plume ejected regolith. The current state of the art of landing and launching from the lunar surface is to land/launch on unprepared regolith surfaces. Though this has been a relatively successful approach, significant risks exist for the Artemis Program due to higher thrust levels leading to increased ejecta and cratering, presence of co-located assets in the ejecta path, and potential strict surface levelness requirements. Regolith-thermoset polymer composite materials were developed and evaluated for off Earth launch and landing pad applications. Performance under hot fire conditions was assessed for two simulated Starship lunar launch/landing environments, one targeting thermal conditions and the second targeting pressure conditions. Paver test articles were prepared at 20% and 11% polymer mass fractions. Sintered paver test articles were prepared with 20% polymer grouting filling the seams between pavers. Though significant erosion was experienced during the more extreme thermal testing conditions, all test articles successfully mitigated regolith ejecta from plume effects. A concept for preparing and emplacing the materials was developed and tested in laboratory conditions. The testing evaluated the feasibility of using twin and single screw extruder technology to mix, convey and deposit materials. Both the twin and single screw extruders were capable of processing and extruding the composite with a maximum of 90% mass fraction of regolith achieved by the twin screw extruder.A primary risk for application of regolith-thermoset polymer composites as lunar launch/landingpad is the mass of polymer required to be landed on the moon. Calculations were performed that show that a 100 m diameter, 0.025 m thick pad with polymer mass fraction of 15% will require a payload mass of 72 mt to the Lunar surface. This is below the planned Starship payload capacity to the lunar surface of 100 mt. The regolith-thermoset polymer composite based construction approach proved feasibility in three critical areas: performance under launch/landing conditions, demonstration of a mixing and depositing strategy, and fitting within the planned lunar payload capacity. It is recommended that materials and systems be developed to TRL 6 for a small-scale lunar demonstration of emplacement of a launch/landing pad via a CLPS mission to support Artemis Program roadmap gap closure activities.

ISRU↗
NASA NTRSDate not supplied

In-situ Lunar Launch and Landing Pad Construction with Regolith-Thermoset Polymer Composite Materials

Lunar launch and landing pads are necessary to mitigate risks to lander/ascent vehicles and surrounding surface assets from rocket plume ejected regolith. The current state of the art of landing and launching from the lunar surface is to land/launch on unprepared regolith surfaces. Significant risks exist for the larger landers proposed for the Artemis Program due to higher thrust levels leading to increased ejecta and cratering, presence of co-located assets in the ejecta path, and potential strict surface levelness requirements for tall vehicles.

Launch Pad↗
NASA NTRSDate not supplied

Investigation into Stimulated Microgravity Techniques used to Study Biofilm Growth

Bacterial growth in liquid media in microgravity conditions is not well understood. Trends such as a shortened lag phase, longer log phase, slower growth rate, and a higher final population concentration have been noted but the underlying cause remains unclear. At the single cell level, it is predicted that bacteria are less gravity-sensitive than larger species. The effects on their immediate environment, including the lack of cell settlement and slower mass transfer of nutrients due to lack of density driven convection, could help explain the trends. Ground-based spaceflight analogs, or simulated microgravity devices, are often employed to achieve different attributes of weightlessness to study effects on bacterial growth. Though these technologies could isolate gravity’s role in various biological processes, they cannot replicate all its effects and underlying mechanisms. Hence, interpretation of results could be misleading, even if similar to spaceflight. In this study two common simulated microgravity devices were investigated to determine whether they could simulate relevant microgravity conditions for bacterial growth. A bioreactor, the high aspect ratio vessel (HARV), was used with dyes of different density mounted on a random positioning machine (RP machine) or a rotating wall vessel (RWV). The RP machine displayed higher mixing rates than the RWV. The RWV was further tested at different rotations per minute (RPM). The range to minimize effects of density driven convection (low speeds) or centrifugal forces (high speeds) was between a range of 15-20 RPM. These results will help inform the selection of simulated microgravity device as well as interpretation of subsequent biofilm growth results.

Angie M. Diaz↗
NASA NTRSDate not supplied

Moon-to-Mars Planetary Construction Technology (MMPACT) Scoop, Tamp, Filter (STF) Sub-System

NASA’s Space Technology Mission Directorate “champions technologies needed to live on and explore the Moon” [1]. This includes capabilities that capitalize on existing lunar resources and carry out surface manufacturing and construction activities. The goal of the Moon-to-Mars Planetary Construction Technology (MMPACT) Project is to mature these two capabilities. The primary resource on the Moon and the primary feedstock for manufacturing and construction is regolith. In the past, astronauts launched, landed, and lived in a spacecraft. NASA envisions a future where we make living spaces on the lunar surface instead. The innovative technologies required for lunar surface construction may be something never seen before, or they may be adaptations of existing technologies. This paper summarizes recent efforts to develop and test a scoop, tamp and filter (STF) sub-system to prepare and deposit lunar regolith for a laser-based vitreous material transformation system being developed under a NASA contract by ICON, inc., which is hoped to eventually be used for automated additive construction with indigenous regolith on the Moon.

Moon↗