Engineering topics

Jonathan S. Litt

Publications and source records attributed to Jonathan S. Litt.

At least 19 records

NASA NTRS2025

Piloted Evaluation of a Fault Recovery System for an Aircraft with Distributed Electric Propulsion

Electrified aircraft powertrains contain multiple tightly coupled subsystems, making them much more complex than traditional aircraft propulsion systems, both in terms of integration and control. Electrification enables aircraft to have multiple distributed thrust-producing fans that the flight control system can utilize for enhanced maneuverability, further increasing the control complexity. The SUbsonic Single Aft eNgine (SUSAN) Electrofan is a NASA concept aircraft that leverages this technology. SUSAN is a series/parallel partial hybrid electric single-aisle transport aircraft that takes advantage of its electrified powertrain to provide fuel burn and emissions benefits when compared to the state-of-the-art. Achieving these benefits requires an appropriately designed control architecture that coordinates the various powertrain and flight control subsystems. As such, the SUSAN aircraft is designed with a high level of automation, allowing it to properly manage coupled subsystems and react rapidly to failures and anomalies. To do this effectively, algorithms that perform component health management, fault detection, isolation, and accommodation, and continuous optimization, must be developed, tested, validated, and implemented. This paper describes a piloted evaluation of such an algorithm in scenarios with multiple fan failures, performed in a flight simulator, demonstrating failure recovery and continued safe operation up to the limits of the powertrain. These scenarios are subsequently related to certification requirements.

Electrified Aircraft Propulsion↗

NASA NTRS2024

Optimal Control Allocation for Distributed Electric Propulsion in a Series/Parallel Partial Hybrid Powertrain

The SUbsonic Single Aft eNgine (SUSAN) Electrofan is a NASA concept jet transport aircraft with a 2040 entry-into-service date. It utilizes electrified aircraft propulsion (EAP) to enable propulsive and aerodynamic benefits to reduce fuel usage, emissions, and cost. The powertrain consists of a single thrust producing, boundary layer-ingesting (BLI) turbofan gas turbine engine (GTE) with generators driving a series/parallel partial hybrid EAP system. The architecture includes 16 underwing contrarotating BLI fans, eight on each side, in a mailslot configuration. The 16 fans run on power extracted from the GTE through four 5 MW motor/generators connected to the Low-Pressure Spool, and a single 1 MW motor/generator on the High-Pressure Spool. The distributed fans can be used by the flight control to augment or replace the rudder function. At top of climb, the power extracted from the GTE for the fans is boosted by batteries. The design provides redundancy, and the capacity for boost means that the fans are designed to be able to provide additional thrust when necessary. These features can be leveraged in case of a fan or generator failure. This paper sets up the optimal control problem of setpoint determination for individual fans in the distributed propulsion system, accounting for electrical string efficiencies, saturations, and failures. The solution minimizes power consumption while maintaining thrust and torque on the airframe for maneuvering. Additionally, thrust that would have been lost due to temporary fan speed or power saturation is optimally redistributed to maintain overall desired thrust and torque on the aircraft. The power extraction range constraints derive from the gas turbine engine design and the small amount of variation allowed for the engine to maintain operability. The problem formulation allows the number and location of fan failures for which the thrust and torque can be maintained to be investigated, which has implications for certification. Simulations of a coordinated turn utilizing the distributed electric propulsion for yaw rate control under different failure scenarios demonstrate the robustness of the powertrain design to failures and help define its limitations.

Distributed Electric Propulsion↗

NASA NTRS2024

Revolutionary Vertical Lift Technology Lift + Cruise Concept Vehicle Powertrain Dynamic Model

The Lift + Cruise (L+C) is one of several Revolutionary Vertical Lift Technology (RVLT) concept aircraft identified by NASA to investigate Urban Air Mobility (UAM) requirements. This six-passenger vehicle has a conventional tube-and-wing configuration, but with eight lift rotors (four on each wing) and a pusher rotor on the tail. This arrangement allows it to take off and land vertically as well as fly like an airplane. This report presents a novel dynamic model of the L+C powertrain built using the Toolbox for the Modeling and Analysis of Thermodynamic Systems (T-MATS) and the Electrical Modeling and Thermal Analysis Toolbox (EMTAT), both of which are NASA-developed toolboxes, and together are capable of modeling hybrid-electric powertrain architectures. This research effort models the complex behavior of the powertrain at the mechanical timescale (15 to 20 ms). The model consists of a turboshaft engine, generator, direct current bus, energy storage management system, gearboxes, and electric propulsor systems coupled together to create a dynamic model that mimics the operation of the multidomain powertrain. Two control algorithms, designed to equalize the power consumed to the power produced, are compared to assess their practicality: (1) independent proportional-integral (PI) control and (2) linear quadratic integral regulator (LQIR) control. Simulation results highlight the key features present in the model and demonstrate its operation under the two control schemes.

revolutionary vertical lift technology↗

NASA NTRS2024

Transient Optimization of an Electrified Gas Turbine Engine Using Machine Learning

Gas turbine engines are designed with sufficient margin to prevent stall under normal operating conditions throughout their life. This compromise ensures that during rapid accelerations, compressor operation remains stable, but at the cost of efficiency and thrust responsiveness. The design margin encompasses multiple sources of uncertainty and systematic deviances from the operating line, the largest of which is the transient allowance. This set-aside accounts for the temporary incoordination of the engine spools during an acceleration while still enabling it to meet the certification requirement to accelerate from low to high power within a specified time, and without experiencing overtemperature, surge, stall, or other detrimental factors. Electrification of the powertrain provides the opportunity to address this reserve and truly optimize the design. The addition of electric machines inherent in hybrid propulsion concepts offers a means to interact with the engine shafts such that the necessary margin can be reduced, which can positively impact the engine design. By adjusting the amount of power extracted from or injected to the engine spools by the electric machines during transient operation, excursions from the operating line can be minimized. Past work using a dynamic engine model has shown that optimization of the fuel flow schedule during acceleration can reduce the required margin while still meeting the time requirement, and results are further improved when combined with power injection and extraction. The current work uses machine learning through a genetic algorithm to address the problem holistically by concurrently optimizing the electric machine power command and fuel flow acceleration schedule using an updated, higher fidelity version of the original engine model.

Stall Margin↗

NASA NTRS2024

System Health Management for a Series/Parallel Partial Hybrid Powertrain with Distributed Electric Propulsion

Electrified aircraft powertrains contain multiple interacting subsystems, making them much more complex than traditional aircraft propulsion systems in terms of integration and control. Electrification enables aircraft to have distributed thrust-producing fans that the flight control system can leverage for enhanced maneuverability, further increasing the control complexity. A NASA concept aircraft, the SUbsonic Single Aft eNgine (SUSAN) Electrofan, is such a vehicle. SUSAN is a series/parallel partial hybrid-electric single-aisle transport aircraft that takes advantage of its electrified powertrain to provide fuel burn and emissions benefits when compared to the state-of-the-art. Achieving these benefits requires an appropriately designed control architecture that coordinates the various powertrain and flight control subsystems. As such, the SUSAN aircraft is designed with a high level of automation, allowing it to properly manage coupled subsystems and react rapidly to failures and anomalies. To do this effectively, algorithms that perform component health management, fault detection, isolation, and accommodation, and continuous optimization, must be developed and implemented. This paper describes the development of some of these algorithms for system health management applied to the powertrain of the SUSAN concept aircraft.

Electrified Aircraft Propulsion↗

NASA NTRS2023

Exploring Synoptic Display Concepts for Hybrid-Electric Airliner Flightdecks

The advent of hybrid-electric aircraft concepts with distributed propulsion has resulted in relatively complicated powertrain designs. Determining the optimal approach to display information about the hybrid system in the flightdeck has taken on great importance. At NASA Glenn Research Center, the concept SUbsonic Single Aft eNgine (SUSAN) hybrid airliner has been modeled inside a flight simulator where different flight deck displays can be evaluated. This work focused on ways to display information that reduce clutter and information overload without degrading the crew’s ability to operate the aircraft and respond properly to emergencies. The displays’ layout and symbologies were created to be intuitive to the pilots. This paper documents iterations of synoptic displays and discusses the rationale and tradeoffs behind each variation.

Pilot Displays↗

NASA NTRS2023

Harnessing the Digital Transformation for Development of Electrified Aircraft Propulsion Control Systems

Hybrid electric aircraft propulsion is an emerging technology that presents a variety of potential benefits along with technical integration challenges. Developing these new propulsion architectures with their complex control systems, and ultimately proving their benefit, is a multistep process. This process includes concept development and analysis, dynamic simulation, hardware-in-the-loop testing, full-scale testing, and so on. This effort is being revolutionized and indeed enabled by new digital tools that support increasing the technology readiness level throughout the maturation process. As part of this Digital Transformation, NASA has developed a suite of publicly available digital tools that facilitate the path from concept to implementation. This paper describes the NASA-developed tools and puts them in the context of control system development for hybrid electric aircraft propulsion. The three MATLAB®-based software packages are the Toolbox for the Modeling and Analysis of Thermodynamic Systems (T-MATS), the Electrical Modeling and Thermal Analysis Toolbox (EMTAT), and the Thermal Systems Analysis Toolbox (TSAT). These tools are interactive, complementary, and compatible with each other. T-MATS is a modular thermodynamic modeling framework designed for creating custom component level models of jet engines. EMTAT is a modeling framework used to simulate a variety of power electronic devices, using both physics-based and power flow calculations. TSAT is a framework for modeling and analysis of dynamic heat transfer. These packages all consist of graphical, drag-and-drop, parameterizable building blocks representing various components of the system to be modeled, e.g., compressors, turbines, motors, energy storage devices, etc. They are designed to enable the user to model and simulate the end-to-end dynamic operation of a hybrid electric gas turbine engine powertrain at the timescale of the turbomachinery, capturing mechanical, electrical, and thermal interactions. This paper demonstrates through multiple examples how these tools have been used successfully in a variety of applications, including several of the early stages of hybrid electric gas turbine engine propulsion system development, from the initial system modeling to real-time interactive pilot-in-the-loop simulation to physical hardware-in-the-loop testing, each step bringing the technology closer to fruition.

hybrid electric propulsion↗

NASA NTRS2023

Flight Simulator Demonstration and Certification Implications of Powertrain Failure Mitigation in a Partial Turboelectric Aircraft

The Single-aisle Turboelectric AiRCraft with Aft Boundary Layer propulsor (STARC ABL) is a concept aircraft with a partial turboelectric powertrain. The complexity and integrated nature of the partial turboelectric powertrain architecture presents failure modes and hazards not found in conventional aircraft propulsion designs. Previously, various electrical and mechanical faults and associated recovery modes were demonstrated in a dynamic model of the powertrain. It was shown that certain faults were catastrophic without recovery logic, due specifically to the interaction of the subsystems. However, in each case, the logic, known as a reversionary control mode, enabled continued operation with assumed sufficient thrust to maintain safe flight. The current work evaluates the powertrain faults and recovery strategies using a full aircraft model in a piloted flight simulator, and places it in the context of current regulatory practice. Faults initiated in flight were successfully mitigated, with the accommodated aircraft subsequently evaluated against certification requirements for three-engine aircraft, which were shown to be appropriate for the STARC-ABL configuration.

certification↗

NASA NTRS2023

Comparing the Electrical Modeling and Thermal Analysis Toolbox Simulation Data to Electrified Aircraft Propulsion Test Hardware Data

A model using the Electrical Modeling and Thermal Analysis Toolbox (EMTAT), a National Aeronautics and Space Administration (NASA)-developed Simulink® model block library of electrical components, was developed to mirror the Hybrid Propulsion Emulation Rig (HyPER) hardware, a laboratory focused on Electrified Aircraft Propulsion (EAP) hardware tests. The goal of the model was to demonstrate the utility of the library by comparing the accuracy of the library models to the performance of real hardware, with the primary metrics being the simulation outputs matching physical test hardware data within 5 percent of full scale. The objective of this paper is to present the background, setup, testing and results of this comparison. It describes some of the adjustments that were necessary to match the system hardware, as well as next steps in verification and validation. The outputs of the model were compared to the results of several tests in HyPER, and in the process captured an additional torque loss that is still being analyzed for the root cause but has been confirmed in the hardware. Across all the test series, only one key model parameter was outside the target 5 percent full scale matching, and nearly 70 percent were within 1 percent.

Mark E. Bell↗

NASA NTRS2022

Implementation Approach for an Electrified Aircraft Concept Vehicle in a Research Flight Simulator

This paper describes a process to develop a flight simulation test capability for the SUbsonic Single Aft eNgine (SUSAN) Electrofan, a subsonic regional jet transport aircraft concept that utilizes electrified propulsion to gain benefits in fuel usage, emissions, and cost. The process, which involves the integration of independently developed models and their subsequent implementation in a flight simulator, is general and can be applied to a variety of aircraft types. However, the use of electrified propulsion architectures has the potential to add complexity beyond that of a traditional aircraft, especially with regard to the pilot interface. The way the pilot interacts with the thrust producing components could vary significantly between architectures, and the information displayed to the pilot will necessarily include additional variables beyond what is normally displayed in a traditional cockpit. This paper describes the integration process in general, as well as specific accommodations made for the architecture under consideration.

flight simulation↗

NASA NTRS2020

Electrical Modeling and Thermal Analysis Toolbox (EMTAT) User’s Guide

A simulation toolbox has been developed to model the electrical portions of Electrified Aircraft Propulsion (EAP) systems, including self-heating of electrical systems. Dynamic models of EAP systems often include turbomachinery, an electrical power system, and a thermal management system. These portions of the propulsion system can operate on timescales covering six orders of magnitude, which poses a challenging modeling task. Assumptions and approximations are made in an effort to capture the dynamics relevant to engine, electrical system, and thermal system interactions, while still allowing for fast simulations. These assumptions and approximations enable the electrical component models to run at the time scale of the turbomachinery, neglecting the very high frequency electrical dynamics, while demonstrating representative behavior of the end-to-end system. Thus the models execute in an acceptable time frame for what would otherwise be an extremely stiff simulation. The resulting simulations of EAP systems are appropriate for system-level control design and analysis. The objective of this User's Guide is to present an overview of the usage of the Electrical Modeling and Thermal Analysis Toolbox (EMTAT). It will describe some of the approximations made to accommodate rapid execution, and some of the design tools that allow matching the model to component specifications. This paper will describe the basic usage of the software toolbox, and also provide an example of EAP system modeling using EMTAT.

Mark E. Bell↗

NASA NTRSDate not supplied

Implementation Approach for an Electrified Aircraft Concept Vehicle in a Research Flight Simulator

•To describe the development of a dynamic model of an electrified propulsion integrated aircraft concept vehicle appropriate for implementation in a research flight simulator. •To bring up questions related to flight decks for electrified propulsion integrated aircraft. →Ultimate implementation of the model should be based on the procedure outlined here and more fully described in the paper →The flight deck requirements for a 2040 entry-into-service type vehicle with electrified propulsion need to be defined and implemented to the extent possible within the existing cockpit

flight simulation↗

NASA NTRSDate not supplied

Subsonic Single Aft Engine (SUSAN) Transport Aircraft Concept and Trade Space Exploration

A trade space exploration of a new NASA regional transport aircraft concept called the SUbsonic Single Aft eNgine (SUSAN) Electrofan is presented. The SUSAN concept uses a 20MW Electrified Aircraft Propulsion (EAP) system to enable advance Propulsion Airframe Integration (PAI) in transport category aircraft. Alternative fuels will be used to reduce the amount of emissions per energy used. By combining these features there is the potential to reduce aircraft emissions by 50% per passenger/mile while retaining the size, speed, and range of large regional jets. SUSAN is has a 750 mile economic mission, a 2500 mile design range and a maximum capacity of 180 passengers. The SUSAN configuration utilizes a single aft mounted engine and distributed electric wing-mounted thrusters on a tube and wing arrangement with a T-tail empennage. The SUSAN Electrofan employs a hybrid powertrain to enable: single turbofan operation on a large transport category aircraft; increased aerodynamic and propulsive efficiency through placement of electric engines; optimized turbofan sizing and efficiency through control and electric boosting, reduced control surface sizing through thrust augmentation. A single use battery is employed as the power source in case of turbofan failure. The design study also considers the constraints of operating within the current airport, airspace and economic constraints. This paper presents the status of the trade space exploration; however the concept definition is not finished. Forward work includes optimizing the overall aircraft configuration and including certain hard to model features like boundary layer ingestion or natural laminar flow across all appliable subsystems. Additional work forward work is a more extensive analysis of the configuration using alternative fuels.

Ralph H. Jansen↗

NASA NTRSDate not supplied

Implementation Approach for an Electrified Aircraft Concept Vehicle in a Research Flight Simulator

A flight simulation test capability for the SUbsonic Single Aft eNgine (SUSAN) Electrofan is under development. SUSAN is a regional jet transport aircraft concept that utilizes electrified propulsion to gain benefits in fuel usage, emissions, and cost. The process, which involves the integration of independently developed models and their subsequent implementation in a flight simulator, is general and can be applied to a variety of aircraft types. However, the use of electrified propulsion adds complexity beyond that of a traditional aircraft, especially with regard to the pilot interface. The way the pilot interacts with the engines will differ from current practice, and the information displayed to the pilot will necessarily include additional variables beyond what is normally displayed in a traditional cockpit.

flight simulation↗

NASA NTRSDate not supplied

Update on Subsonic Single Aft Engine (SUSAN) Electrofan Trade Space Exploration

NASA is conducting an ongoing trade study analysis of the SUSAN Electrofan aircraft concept, which utilizes 20-MW-class electrified aircraft propulsion to enable propulsive, aerodynamic, and control benefits while retaining the range, speed, and size of typical narrow-body regional aircraft. The study is constrained by the ground rules of operating within the current airport and airspace infrastructure. This ongoing study seeks to find a configuration and combination of technologies that yield significant fuel burn and emissions benefits. Another key goal is to reduce cost per passenger mile. Currently, the study is focused on a configuration that utilizes jet A or sustainable aviation fuels, however, we plan to consider other fuel alternatives in the future. This presentation describes the progress in defining the architecture of the aircraft, engine, power system, control system, and initial understandings of the sensitivity of the potential configurations to technology assumptions based on key performance parameters. Additionally, progress towards definition and refinement of driving operational, economic, infrastructure, certification, and technical requirements is discussed.

Ralph H. Jansen↗

NASA NTRSDate not supplied

Comparing the Electrical Modeling and Thermal Analysis Toolbox Simulation Data to Electrified Aircraft Propulsion Test Hardware Data

The Electrical Modeling and Thermal Analysis Toolbox (EMTAT), a National Aeronautics and Space Administration (NASA)-developed Simulink™ model block library of electrical components developed with the goal of facilitating system-level control design and analysis, has two levels of fidelity depending on the test needs. The Physics Based model blocks are designed to use physical component characteristics to more accurately model real hardware, including power losses, efficiency, thermal effects, electromagnetic losses, voltage drops and current requirements. These blocks model electrical dynamics that occur at the millisecond turbomachinery time scale which allows for faster-than-real-time electrified turbomachinery simulations. A model was developed to mirror the Hybrid Propulsion Emulation Rig (HyPER) hardware, a laboratory focused on Electrified Aircraft Propulsion (EAP) hardware tests. The present hardware setup supports Turbine Electrified Energy Management (TEEM) testing. The outputs of the model were compared to the results of several tests on the HyPER laboratory motor-generator setup with the goal of matching the steady state simulation data to steady state hardware data within 5% of full scale. The objective of this paper is to present the background, setup, testing and results of this comparison. It will describe some of the adjustments that were necessary to match the system hardware, as well as next steps in verification and validation.

Hyper↗

NASA NTRSDate not supplied

SUSAN Power/Propulsion System Emulation Test Predictions

The development of all-electric and hybrid-electric propulsion systems for transport aircraft presents an opportunity for new designs that can reduce fuel consumption and emissions from commercial aviation while enabling safer and more reliable aircraft. The SUbsonic Single Aft eNgine (SUSAN) is a conceptual design for a single-aisle transport aircraft with a series/parallel partial-hybrid propulsion system that is being developed by NASA as a reference design for single-aisle transport with a high degree of electrification. The SUSAN aircraft incorporates multiple tightly coupled power, propulsion, and flight control systems. This coupling leads to challenges in the aircraft control design process, requiring a hierarchical and more coordinated control architecture. This presentation will summarize the plans for a Hardware-in-the-Loop (HIL) test performed in the Hybrid Propulsion Emulation Rig (HyPER) facility at NASA Glenn Research Center (GRC). During this test, a real-time reference model of the full-scale SUSAN powertrain and controllers will be run alongside a sub-scale electro-mechanical system representing a portion of the electrified components in the SUSAN hybrid powertrain. This test will allow the performance of the SUSAN controllers to be evaluated using real powertrain components and allows side-by-side comparison between the real and modeled subsystems. This presentation will summarize the full-scale system model, steps towards integration of representative hardware for future control testing, and predicted results.

Jonah J. Sachs-Wetstone↗

NASA NTRSDate not supplied

System Health Management for a Series/Parallel Partial Hybrid Powertrain with Distributed Electric Propulsion

Electrified Aircraft Propulsion↗