Engineering topics

Jones, Daniel R.

Publications and source records attributed to Jones, Daniel R..

4 records

NASA NTRS2019

Physical Simulation of Rocket Exhaust Aerodynamics Using Heated Ethane: Conceptual Foundations

Heated ethane (C2H6) has been proposed as an alternative to inert gases for use as a motive fluid in the experimental simulation of rocket exhaust plumes. By adjusting stagnation temperature, the isentropic exponent of ethane can be tuned to approximate those produced by common rocket propellants including hydrogen, hypergols, alcohols, and hydrocarbons. As a result, ethane can be made to follow a nozzle expansion process which is nearly identical to realistic rocket engine flow fields. Additionally, its high auto-ignition temperature and resistance to condensation enable the testing of expansion ratios much larger than conventional inertgas testing. NASA SSC has performed quasi-one-dimensional analyses using the Chemical Equilibrium with Applications (CEA) code as a preliminary means to compare flow fields produced by non-reacting ethane to those of reacting combustion products. A LO2/LH2 rocket engine operating at a chamber pressure of 5.0 MPa and a mixture ratio of 6.1 was used as an example case to demonstrate ethane’s efficacy as a simulant. Errors for key similarity parameters were compared to legacy cold-flow test methods. Additional errors induced by machining tolerances and chemical impurities were also examined. Results suggest that at a 3% geometric scale and ~500 K ethane stagnation temperature, an error of less than 2.5% throughout the flow field is realistically achievable along the dimensions of Mach number, Reynolds number, pressure ratio, and isentropic exponent. The development of an experimental test bed for validation of this configuration is currently underway.

Jones, Daniel R.↗

NASA NTRS2016

Passive Rocket Diffuser Testing: Reacting Flow Performance of Four Second-Throat Geometries

Second-throat diffusers serve to isolate rocket engines from the effects of ambient back pressure. As one of the nation's largest rocket testing facilities, the performance and design limitations of diffusers are of great interest to NASA's Stennis Space Center. This paper describes a series of tests conducted on four diffuser configurations to better understand the effects of inlet geometry and throat area on starting behavior and boundary layer separation. The diffusers were tested for a duration of five seconds with a 1455-pound thrust, LO2/GH2 thruster to ensure they each reached aerodynamic steady state. The effects of a water spray ring at the diffuser exits and a water-cooled deflector plate were also evaluated. Static pressure and temperature measurements were taken at multiple axial locations along the diffusers, and Computational Fluid Dynamics (CFD) simulations were used as a tool to aid in the interpretation of data. The hot combustion products were confirmed to enable the diffuser start condition with tighter second throats than predicted by historical cold-flow data or the theoretical normal shock method. Both aerodynamic performance and heat transfer were found to increase with smaller diffuser throats. Spray ring and deflector cooling water had negligible impacts on diffuser boundary layer separation. CFD was found to accurately capture diffuser shock structures and full-flowing diffuser wall pressures, and the qualitative behavior of heat transfer. However, the ability to predict boundary layer separated flows was not consistent.

Jones, Daniel R.↗

NASA NTRS2016

Passive Rocket Diffuser Theory: A Re-Examination of Minimum Second Throat Size

Second-throat diffusers serve to isolate rocket engines from the effects of ambient back pressure during testing without using active control systems. Among the most critical design parameters is the relative area of the diffuser throat to that of the nozzle throat. A smaller second throat is generally desirable because it decreases the stagnation-to-ambient pressure ratio the diffuser requires for nominal operation. There is a limit, however. Below a certain size, the second throat can cause pressure buildup within the diffuser and prevent it from reaching the start condition that protects the nozzle from side-load damage. This paper presents a method for improved estimation of the minimum second throat area which enables diffuser start. The new 3-zone model uses traditional quasi-one-dimensional compressible flow theory to approximate the structure of two distinct diffuser flow fields observed in Computational Fluid Dynamics (CFD) simulations and combines them to provide a less-conservative estimate of the second throat size limit. It is unique among second throat sizing methods in that it accounts for all major conical nozzle and second throat diffuser design parameters within its limits of application. The performance of the 3-zone method is compared to the historical normal shock and force balance methods, and verified against a large number of CFD simulations at specific heat ratios of 1.4 and 1.25. Validation is left as future work, and the model is currently intended to function only as a first-order design tool.

Jones, Daniel R.↗

NASA NTRS2014

Development of Modeling Approaches for Nuclear Thermal Propulsion Test Facilities

High efficiency of rocket propul-sion systems is essential for humanity to venture be-yond the moon. Nuclear Thermal Propulsion (NTP) is a promising alternative to conventional chemical rock-ets with relatively high thrust and twice the efficiency of the Space Shuttle Main Engine. NASA is in the pro-cess of developing a new NTP engine, and is evaluat-ing ground test facility concepts that allow for the thor-ough testing of NTP devices. NTP engine exhaust, hot gaseous hydrogen, is nominally expected to be free of radioactive byproducts from the nuclear reactor; how-ever, it has the potential to be contaminated due to off-nominal engine reactor performance. Several options are being investigated to mitigate this hazard potential with one option in particular that completely contains the engine exhaust during engine test operations. The exhaust products are subsequently disposed of between engine tests. For this concept (see Figure 1), oxygen is injected into the high-temperature hydrogen exhaust that reacts to produce steam, excess oxygen and any trace amounts of radioactive noble gases released by off-nominal NTP engine reactor performance. Water is injected to condense the potentially contaminated steam into water. This water and the gaseous oxygen (GO2) are subsequently passed to a containment area where the water and GO2 are separated into separate containment tanks.

Jones, Daniel R.↗