Search NASA⌕ Search

Engineering topics

Jones, H. E.

Publications and source records attributed to Jones, H. E..

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Observations on computational methodologies for use in large-scale, gradient-based, multidisciplinary design incorporating advanced CFD codes

How a combination of various computational methodologies could reduce the enormous computational costs envisioned in using advanced CFD codes in gradient based optimized multidisciplinary design (MdD) procedures is briefly outlined. Implications of these MdD requirements upon advanced CFD codes are somewhat different than those imposed by a single discipline design. A means for satisfying these MdD requirements for gradient information is presented which appear to permit: (1) some leeway in the CFD solution algorithms which can be used; (2) an extension to 3-D problems; and (3) straightforward use of other computational methodologies. Many of these observations have previously been discussed as possibilities for doing parts of the problem more efficiently; the contribution here is observing how they fit together in a mutually beneficial way.

Newman, P. A.↗
NASA NTRS1992

An approximately factored incremental strategy for calculating consistent discrete aerodynamic sensitivity derivatives

An incremental strategy is presented for iteratively solving very large systems of linear equations, which are associated with aerodynamic sensitivity derivatives for advanced CFD codes. It is shown that the left-hand side matrix operator and the well-known factorization algorithm used to solve the nonlinear flow equations can also be used to efficiently solve the linear sensitivity equations. Two airfoil problems are considered as an example: subsonic low Reynolds number laminar flow and transonic high Reynolds number turbulent flow.

Korivi, V. M.↗
NASA NTRS1991

Directivity and prediction of low frequency rotor noise

Acoustic data obtained over a large horizontal plane under the model rotor and digitally filtered in order to determine the low-frequency content near the blade passage frequency is analyzed. Focus is placed on the directivity of low-frequency noise, and the changes in directivity as a function of the descent glide slope angle and advance ratio are presented and compared with predicted directivity results. The differences between the data and prediction are discussed for two observer positions, one below and on the rotor axis, and the other 60 degrees down from the horizontal. It is demonstrated that for the latter position, blade-vortex interaction noise is strong when it occurs, and the loading at the low frequencies is significantly affected during blade-vortex interactions.

Burley, C. L.↗
NASA NTRS1987

Computation of transonic potential flow on helicopter rotor blades

Two computer codes, the full-potential three-dimensional (FP3D) code and the full-potential rotor (FPR) code have recently been developed. Both of these codes solve the three-dimensional conservative formulation of the full potential equation. The FPR code was developed at the U.S. Army Aeroflightdynamics Directorate (AFDD) while the FP3D code was a joint development by ONERA and AFDD. Both of these codes were used to predict the nonlifting, unsteady flow over a rotor operating at high advance ratio and tip speed. Three different rotor tip planform shapes were studied: a rectangular tip, a 30 deg aft swept tip and a 30 deg forward swept tip. Results of these computations are compared to results obtained using an earlier small-disturbances code. Also, the lifting flow over a rectangular tip operating at a slightly different condition was computed. These results are also compared with the small disturbances computations and with experimental results.

Costes, M.↗
NASA NTRS1986

Full potential modeling of blade-vortex interactions

A comparison is made of four different models for predicting the unsteady loading induced by a vortex passing close to an airfoil. (1) The first model approximates the vortex effect as a change in the airfoil angle of attack. (2) The second model is related to the first but, instead of imposing only a constant velocity on the airfoil, the distributed effect of the vortex is computed and used. This is analogous to a lifting surface method. (3) The third model is to specify a branch cut discontinuity in the potential field. The vortex is modeled as a jump in potential across the branch cut, the edge of which represents the center of the vortex. (4) The fourth method models the vortex expressing the potential as the sum of as known potential due to the vortex and an unknown perturbation due to the airfoil. The purpose of the current study is to investigate the four vortex models described above and to determine their relative merits and suitability for use in large three-dimensional codes.

Jones, H. E.↗
NASA NTRS1986

Full-potential modeling of blade-vortex interactions

A comparison is made of four different models for predicting the unsteady loading induced by a vortex passing close to an airfoil. (1) The first model approximates the vortex effect as a change in the airfoil angle of attack. (2) The second model is related to the first but, instead of imposing only a constant velocity on the airfoil, the distributed effect of the vortex is computed and used. This is analogous to a lifting surface method. (3) The third model is to specify a branch cut discontinuity in the potential field. The vortex is modeled as a jump in potential across the branch cut, the edge of which represents the center of the vortex. (4) The fourth method models the vortex expressing the potential as the sum of a known potential due to the vortex and an unknown perturbation due to the airfoil. The purpose of the current study is to investigate the four vortex models described above and to determine their relative merits and suitability for use in large three-dimensional codes.

Jones, H. E.↗
NASA NTRS1979

Small solar thermal electric power plants with early commercial potential

Cost-effective small solar thermal electric power plants (1- to 10-MW nominal size) offer an attractive way of helping the world meet its future energy needs. The paper describes the characteristics of a conceptual near-term plant (about 1 MW) and a potential 1990 commercial version. The basic system concept is one in which steam is generated using two-axis tracking, parabolic dish, and point-focusing collectors. The steam is transported through low-loss piping to a central steam turbine generator unit where it is converted to electricity. The plants have no energy storage and their output power level varies with the solar insolation level. This system concept, which is firmly based on state-of-the-art technology, is projected to offer one of the fastest paths for U.S. commercialization of solar thermal electric power plants through moderate technology advances and mass production.

Jones, H. E.↗