Engineering topics

Jones, Henry E.

Publications and source records attributed to Jones, Henry E..

15 records

NASA NTRS2009

Navier-Stokes Simulation of a Heavy Lift Slowed-Rotor Compound Helicopter Configuration

Time accurate numerical simulations were performed using the Reynolds-averaged Navier-Stokes (RANS) flow solver OVERFLOW for a heavy lift, slowed-rotor, compound helicopter configuration, tested at the NASA Langley 14- by 22-Foot Subsonic Tunnel. The primary purpose of these simulations is to provide support for the development of a large field of view Particle Imaging Velocimetry (PIV) flow measurement technique supported by the Subsonic Rotary Wing (SRW) project under the NASA Fundamental Aeronautics program. These simulations provide a better understanding of the rotor and body wake flows and helped to define PIV measurement locations as well as requirements for validation of flow solver codes. The large field PIV system can measure the three-dimensional velocity flow field in a 0.914m by 1.83m plane. PIV measurements were performed upstream and downstream of the vertical tail section and are compared to simulation results. The simulations are also used to better understand the tunnel wall and body/rotor support effects by comparing simulations with and without tunnel floor/ceiling walls and supports. Comparisons are also made to the experimental force and moment data for the body and rotor.

Allan, Brian G.↗

NASA NTRS2006

Aerodynamic Characteristics of Two Rotary Wing UAV Designs

This paper presents the results of an experimental investigation of two rotary-wing UAV designs. The primary goal of the investigation was to provide a set of interactional aerodynamic data for an emerging class of rotorcraft. The present paper provides an overview of the test and an introduction to the test articles, and instrumentation. Sample data in the form of a parametric study of fixed system lift and drag coefficient response to changes in configuration and flight condition for both rotor off and on conditions are presented. The presence of the rotor is seen to greatly affect both the character and magnitude of the response. The affect of scaled stores on body drag is observed to be dependent on body shape.

Jones, Henry E.↗

NASA NTRS2006

AERODYNAMIC CHARACTERISTICS OF TWO ROTARY WING UAV DESIGNS

Jones, Henry E.↗

NASA NTRS2006

INITIAL ASSESSMENT OF SURFACE PRESSURE CHARACTERISTICS OF TWO ROTARY WING UAV DESIGNS

This paper presents results of an experimental investigation of two rotary-wing UAV designs. The primary goal of the investigation was to provide a set of interactional aerodynamic data for an emerging class of rotorcraft. The present paper provides an overview of the test and an introduction to the test articles, and instrumentation. Sample data in the form of fixed system pressure coefficient response to changes in configuration attitude and flight condition for both rotor off and on conditions are presented. The presence of the rotor is seen to greatly affect the magnitude of the response. Pressure coefficients were measured using both conventional pressure taps and via pressure sensitive paint. Comparisons between the two methods are presented and demonstrate that the pressure sensitive paint is a promising method; however, further work on the technique is required.

Jones, Henry E.↗

NASA NTRS2002

Maneuvering Rotorcraft Noise Prediction: A New Code for a New Problem

This paper presents the unique aspects of the development of an entirely new maneuver noise prediction code called PSU-WOPWOP. The main focus of the code is the aeroacoustic aspects of the maneuver noise problem, when the aeromechanical input data are provided (namely aircraft and blade motion, blade airloads). The PSU-WOPWOP noise prediction capability was developed for rotors in steady and transient maneuvering flight. Featuring an object-oriented design, the code allows great flexibility for complex rotor configuration and motion (including multiple rotors and full aircraft motion). The relative locations and number of hinges, flexures, and body motions can be arbitrarily specified to match the any specific rotorcraft. An analysis of algorithm efficiency is performed for maneuver noise prediction along with a description of the tradeoffs made specifically for the maneuvering noise problem. Noise predictions for the main rotor of a rotorcraft in steady descent, transient (arrested) descent, hover and a mild "pop-up" maneuver are demonstrated.

Brentner, Kenneth S.↗

NASA NTRS2001

Comprehensive Modeling of the Apache With CAMRAD II

This paper presents a report of a multi year study of the U.S. Army LONGBOW APACHE (AH-64D) aircraft. The goals of this study were to provide the Apache Project Managers Office (PMO) with a broad spectrum of calibrated comprehensive and CFD models of the AH-64D aircraft. The goal of this paper is to present an overview of the comprehensive model which has been developed. The CAMRAD II computer code was chosen to complete this task. The paper first discusses issues that must be addressed when modeling the Apache using CAMRAD. The work required the acquisition of a data base for the aircraft and the development and application of a multidisciplinary computer model. Sample results from various parts of the model are presented. Conclusions with regard to the strengths and weaknesses of simulations based on this model are discussed.

Jones, Henry E.↗

NASA NTRS2001

Comprehensive Modeling of the Apache with CAMRAD II

Jones, Henry E.↗

NASA NTRS2000

On the Coupling of CDISC Design Method with FPX Rotor Code

A rotor section aerodynamics design package is developed by coupling Constrained Direct Iterative Surface Curvature (CDISC) design method with the FPX rotor code. The coupling between the CDISC design and the FPX flow analysis is fully automated. The CDISC design method employs a predictor-corrector procedure iteratively to determine a surface geometry which produces a target pressure distribution, where the target pressure distributions is either pre-defined or automatically generated through flow and geometry constraints. The FPX code is an eXtended Full-Potential rotor Computational Fluid Dynamics (CFD) code, which solves the three-dimensional unsteady full-potential equation in a strong conservative form using an implicit approximate factorization finite-difference scheme with entropy and viscosity corrections. Application of the CDISC design method coupled with the FPX rotor code is made for rotor blades in hovering motions. Several design examples are presented to demonstrate the capability of the new package in rotor section design.

Hu, Hong↗

NASA NTRS2000

Noise Prediction for Maneuvering Rotorcraft

This paper presents the initial work toward first-principles noise prediction for maneuvering rotors. Both the aeromechanical and acoustics aspects of the maneuver noise problem are discussed. The comprehensive analysis code, CAMRAD 2. was utilized to predict the time-dependent aircraft position and attitude, along - with the rotor blade airloads and motion. The major focus of this effort was the enhancement of the acoustic code WOPWOP necessary to compute the noise from a maneuvering rotorcraft. Full aircraft motion, including arbitrary transient motion, is modeled together with arbitrary rotor blade motions. Noise from a rotorcraft in turning and descending flight is compared to level flight. A substantial increase in the rotor noise is found both for turning flight and during a transient maneuver. Additional enhancements to take advantage of parallel computers and clusters of workstations, in addition to a new compact-chordwise loading formulation, are also described.

Brentner, Kenneth S.↗

NASA NTRS1997

Full-Potential Modeling of Blade-Vortex Interactions

A study of the full-potential modeling of a blade-vortex interaction was made. A primary goal of this study was to investigate the effectiveness of the various methods of modeling the vortex. The model problem restricts the interaction to that of an infinite wing with an infinite line vortex moving parallel to its leading edge. This problem provides a convenient testing ground for the various methods of modeling the vortex while retaining the essential physics of the full three-dimensional interaction. A full-potential algorithm specifically tailored to solve the blade-vortex interaction (BVI) was developed to solve this problem. The basic algorithm was modified to include the effect of a vortex passing near the airfoil. Four different methods of modeling the vortex were used: (1) the angle-of-attack method, (2) the lifting-surface method, (3) the branch-cut method, and (4) the split-potential method. A side-by-side comparison of the four models was conducted. These comparisons included comparing generated velocity fields, a subcritical interaction, and a critical interaction. The subcritical and critical interactions are compared with experimentally generated results. The split-potential model was used to make a survey of some of the more critical parameters which affect the BVI.

Jones, Henry E.↗

NASA NTRS1997

A Study of the Effects of Blade Shape on Rotor Noise

A new rotor noise prediction system called the Tiltrotor Aeroacoustic Code (TRAC) has been developed under the Short Haul (Civil Tiltrotor) program between NASA, the Army, and the U.S. helicopter industry. This system couples the comprehensive rotorcraft code CAMRAD.Mod1 with either the high resolution sectional loads code HIRES or the full potential CFD code FPRBVI to predict unsteady blade loads, which are then input to the noise prediction program WOPWOP. In this paper, HIRES will be used to predict the blade-vortex interaction (BVI) noise trends associated with blade shape. The baseline shape selected was a 17% scale model of a contemporary design 4 bladed rotor. Measurements for this rotor were acquired in the Duits-Nederslandse Windtunnel (DNW). The code is used to predict noise for the base configuration and the results are compared to the measured data. This provides a firm foundation for investigating the BVI noise trends associated with blade shape. The shapes selected for study are based on variation of sweep and taper which reflect plausible "passive" design concepts. Comparisons of power required, integrated noise, and aerodynamics are made and important trends are noted.

Jones, Henry E.↗

NASA NTRS1994

Sensitivity derivatives for three dimensional supersonic Euler code using incremental iterative strategy

In a recent work, an incremental strategy was proposed to iteratively solve the very large systems of linear equations that are required to obtain quasianalytical sensitivity derivatives from advanced computational fluid dynamics (CFD) codes. The technique was sucessfully demonstrated for two large two-dimensional problems: a subsonic and a transonic airfoil. The principal feature of this incremental iterative stategy is that it allows the use of the identical approximate coefficient matrix operator and algorithm to solve the nonlinear flow and the linear sensitivity equations; at convergence, the accuracy of the sensitivity derivatives is not compromised. This feature allows a comparatively straightforward extension of the methodology to three-dimensional problems; this extension is successfully demonstrated in the present study for a space-marching solution of the three-dimensional Euler equations over a Mach 2.4 blended wing-body configuration.

Korivi, Vamshi Mohan↗

NASA NTRS1992

Recent advances in steady compressible aerodynamic sensitivity analysis

Sensitivity analysis methods are classified as belonging to either of the two broad categories: the discrete (quasi-analytical) approach and the continuous approach. The two approaches differ by the order in which discretization and differentiation of the governing equations and boundary conditions is undertaken. The discussion focuses on the discrete approach. Basic equations are presented, and the major difficulties are reviewed in some detail, as are the proposed solutions. Recent research activity concerned with the continuous approach is also discussed.

Taylor, Arthur C., III↗

NASA NTRS1992

An incremental strategy for calculating consistent discrete CFD sensitivity derivatives

In this preliminary study involving advanced computational fluid dynamic (CFD) codes, an incremental formulation, also known as the 'delta' or 'correction' form, is presented for solving the very large sparse systems of linear equations which are associated with aerodynamic sensitivity analysis. For typical problems in 2D, a direct solution method can be applied to these linear equations which are associated with aerodynamic sensitivity analysis. For typical problems in 2D, a direct solution method can be applied to these linear equations in either the standard or the incremental form, in which case the two are equivalent. Iterative methods appear to be needed for future 3D applications; however, because direct solver methods require much more computer memory than is currently available. Iterative methods for solving these equations in the standard form result in certain difficulties, such as ill-conditioning of the coefficient matrix, which can be overcome when these equations are cast in the incremental form; these and other benefits are discussed. The methodology is successfully implemented and tested in 2D using an upwind, cell-centered, finite volume formulation applied to the thin-layer Navier-Stokes equations. Results are presented for two laminar sample problems: (1) transonic flow through a double-throat nozzle; and (2) flow over an isolated airfoil.

Korivi, Vamshi Mohan↗

NASA NTRS1992

Multidisciplinary analysis and sensitivity derivatives for isolated helicopter rotors in hover

A new method is presented for using Navier-Stokes results in the system analysis and sensitivity derivative computations for a helicopter rotor in hover. The system coupling includes the interactions between rotor performance, rotor structural properties and aerodynamics (i.e., airfoil shape). Emphasis is placed on the use of high fidelity Navier-Stokes algorithms for the aerodynamic problem. The present formulation is chosen to reduce the number of sensitivity derivative equations and their dimensions as much as possible. In addition, an alternative adjoint formulation is presented which dramatically reduces the computational requirement for disciplines in which there may be a large number of design variables (e.g., aerodynamics). The theoretical method makes use of a combination of derivatives from each discipline; the computation of these derivatives has already been shown to be feasible. Sample computations for the aerodynamic-rotor model coupling and an associated sensitivity derivative are also presented.

Jones, Henry E.↗