Engineering topics

Jones, Thomas C.

Publications and source records attributed to Jones, Thomas C..

At least 19 records

NASA NTRS2020

Controlled Environmental Effects on Creep Test Data of Woven Fabric Webbings for Inflatable Space Modules

eveloping technologies for proposed lunar and Mars space exploration missions. Enhanced habitation sy g studied as potential habitats due to their inherent low mass and small launch volume. One goal of inflatable module research is quantification of the safe-life and end-of-life creep-strain spectrum. Full-scale pressurized inflatable modules are large, costly, and difficult to experimentally study. Therefore, material subcomponents are often studied as an alternative. An experimental thermally controlled long-term creep study of VectranTM webbings for application to inflatable modules is presented. Vectran fibers have high strength and low creep properties. High strength webbing materials are desirable for the load bearing restraint layer of inflatable modules because they are strong, flexible, and lightweight. Characterization of the creep behavior, safe-life, and end-of- life of webbing specimens will help quantify comparable life properties for inflatable modules. Several experimental multiple-year creep studies of webbing specimens in uncontrolled thermal environments have been conducted at NASA Langley Research Center. Experimental data obtained exhibits the classic creep-strain curve due to load, coupled with unique sinusoidal variation due to variation in temperature and humidity over daily and annual time periods. Results also have indicated that specimens fail within a year if the applied load is greater than 50 percent of the rated load. The primary goal of this study is to eliminate thermal effects from the creep data for a group of webbing specimens, and to allow uncontrolled thermal effects to influence the creep data of a second group of webbing specimens. Comparison of both sets of data will define how temperature influences creep data. A unique creep test facility was fabricated to facilitate the generation and comparison of the two sets of data. The facility consists of five creep test stands with an integrated heating and cooling system, and four creep test stands exposed to external environmental or ambient conditions. The facility contains displacement, temperature, humidity, and load sensors. Test specimens consist of one- inch wide, 48-inch long Vectran webbings rated at 12,500 pounds-per-inch. Experimental thermally controlled creep-strain data has been generated for two groups of webbing specimens. Applied load for all test stands was above 9000 lbs and greater than 50 percent of the rated load. Temperatures varied between 58˚F and 83˚F for the four test stands exposed to ambient conditions. Associated creep data exhibited the classic creep- strain profiles. The temperature was set to 72˚F for the five test stands in the controlled temperature environment. Creep data for tests with temperature control also exhibited the classic strain profiles. Data indicated that if the load is greater n thermal effects do not manifest. Therefore, creep tests with loads less than 50 percent of the rated load are planned for in the near future.

Kenner, Winfred S.↗

NASA NTRS2019

Persistent Assets in Zero-G and on Planetary Surfaces: Enabled by Modular Technology and Robotic Operations

Space operations are on the cusp of a revolutionary new operational paradigm that leverages modular systems and recurring robotic visits to “Persistent Assets” enabling asset maintenance, repair, and enhancement. A “Persistent Asset” is defined here as any zero-g or planetary surface system that benefits from in-space assembly (ISA) or multiple visits for servicing, repairs, and upgrades. This term is an extension of the term “Persistent Platform” used by Ms. Pam Melroy at the Defense Advanced Research Projects Agency to describe the vision of the Agency for a geosynchronous Earth orbiting platform. In this paper, the term “Persistent Asset” is introduced to encompass not only zero-g systems; such as telecommunication platforms, Earth observing science platform, Department of Defense platforms, and scientific telescope systems, but also planetary surface systems that support missions such as human outposts, science stations, and in-situ resource utilization systems. In contrast to the current state of the art, where space systems are typically launched as a single unit and operated without any further physical intervention after launch; future systems will be maintained, enhanced and reconfigured in-situ as new technology becomes available or mission needs change. Visits to the persistent asset can be regularly scheduled or dictated by funding constraints enabling a pay-as-you-go approach, which is largely independent of time-constraints and able to exploit launches of opportunity. In this paper, historical in-space assembly activities which relied heavily on astronaut extra-vehicular activity will be reviewed as well as early robotic assembly activities. These approaches will be contrasted with emerging modular approaches supporting realization of a new Persistent Asset operational paradigm. The paper will define attributes of the Persistent Asset paradigm and illustrate advantages by applying the paradigm to two relevant applications: 1) a large space telescope backing structure and 2) the backbone structure for a solar electric transport vehicle. Finally, recently developed unique Persistent Asset elements (modules, and interface approaches) will be described.

Doggett, William R.↗

NASA NTRS2019

Hinge for Use in a Tension Stiffened and Tendon Actuated Manipulator

A tension stiffened and tendon actuated manipulator is provided performing robotic-like movements when acquiring a payload. The manipulator design can be adapted for use in-space, lunar or other planetary installations as it is readily configurable for acquiring and precisely manipulating a payload in both a zero-g environment and in an environment with a gravity field. The manipulator includes a plurality of link arms, a hinge connecting adjacent link arms together to allow the adjacent link arms to rotate relative to each other and a cable actuation and tensioning system provided between adjacent link arms. The cable actuation and tensioning system includes a spreader arm and a plurality of driven and non-driven elements attached to the link arms and the spreader arm. At least one cable is routed around the driven and non-driven elements for actuating the hinge.

Doggett, William R.↗

NASA NTRS2019

Calibration of a Structural Finite Element Model for a Representative Inflatable Space Structure Utilizing Probabilistic Methods and Surrogate Models

A structural finite element model representing a novel inflatable airlock concept has been calibrated using full‐scale test data. The concept, denoted as the Non‐Axisymmetric Inflatable Pressure Structure (NAIPS), was developed under NASA’s Minimalistic Advanced Softgoods Hatch (MASH) Program. The current studies extended previous numerical efforts by incorporating the midbody section of the NAIPS to the dome section and calibrating the model with test data using a process that included surrogate models. Brief overviews of the finite element model and calibration process are provided. The completion of the calibration process provided a model that adequately replicated the test data. The successful demonstration of calibration of a finite element model representing an inflatable habitat provides confidence in the ability to use numerical simulations and associated surrogate models to support design and certification of inflatable space habitats.

Lyle, Karen H.↗

NASA NTRS2019

Review of Habitable Softgoods Inflatable Design, Analysis, Testing, and Potential Space Applications

Inflatable space structures have the potential to significantly reduce the required launch volume of large crewed pressure vessels for space exploration missions. Mass savings can also be achieved via the use of high specific strength softgoods materials, and the reduced design penalty from launching the structure in a densely packaged state. Inflatable softgoods structures have been investigated since the late 1950's, and several major development programs at NASA and in industry have helped advance the state-of-the-art in this technology area. This paper discusses the design, analysis, structural testing, and potential applications for inflatable softgoods structures. In particular, this paper will discuss the design of the multi-layer softgoods shell (inner layer, bladder, structural restraint layer, micrometeoroid orbital debris protection layers, thermal insulation layers, and atomic oxygen layer (for low earth orbit) and the results of material and module-level testing that has been conducted over the past two decades at NASA. Finally, the current utilization of expandable spacecraft structures is discussed, as well as potential future applications including airlocks and habitats on the Lunar Orbital Platform-Gateway, and the surface of the Moon and Mars.

Valle, Gerard↗

NASA NTRS2018

Probabilistic Sensitivity Analyses Incorporating Surrogate Models for the Structural Response of a Representative Inflatable Space Structure

This study concentrates on results from probabilistic analysis and numerical simulation tools to identify parameter sensitivities and assess surrogate model suitability for a novel inflatable airlock concept, specifically the Non-Axisymmetric Inflatable Pressure Structure (NAIPS) under NASA's Minimalistic Advanced Softgoods Hatch (MASH) Program. The current studies extended the demonstration of probabilistic analysis tools to identify parameter sensitivities by: incorporating nonlinear material load-strain property curves and orthotropic representation of the fabric; and exploring the use of surrogate models to facilitate rapid evaluations as new information becomes available, as well as enable optimizations. The airlock model has been simplified to focus on the end dome section. Brief overviews of the finite element model and associated surrogate models are provided along with the probabilistic sensitivity analysis approaches. Responses of interest include the sensitivities of various loads in the structural elements of the NAIPS to material properties, cord lengths, inflation pressure and friction between softgoods components. The use of surrogate models was explored to facilitate rapid sensitivity evaluations as parameter ranges change. The completion of the sensitivity studies improved understanding of the dependence of load responses to several uncertain parameters and confidence in the ability to use surrogate models to represent the finite element simulations.

Lyle, Karen H.↗

NASA NTRS2018

Demonstration of Probabilistic Sensitivity Analyses Tools on the Structural Response of a Representative Inflatable Space Structure

This work provides an initial step toward demonstrating a probabilistic numerical simulation capability to support trade studies and the development of a certification plan for inflatable space habitats. This study concentrates on interpreting the results from probabilistic analysis and numerical simulation tools to identify parameter sensitivities for a novel inflatable airlock concept, specifically the Non‐Axisymmetric Inflatable Pressure Structure (NAIPS) that was designed and tested under NASA's Minimalistic Advanced Softgoods Hatch (MASH) Program. A brief overview of the finite element model is provided along with the probabilistic sensitivity analysis approach. The sensitivity studies required a model that was numerically stable and efficient enough that hundreds of simulations could be completed in the allotted time. Therefore, the existing full model was simplified by: extracting a quarter symmetry section of the dome; focusing on a single inflation pressure; and replacing the non‐linear material stress‐strain curves with linear, isotropic materials defined by elastic moduli. Responses of interest include the sensitivity of various structural component loads to material properties, cord lengths, inflation pressure and friction. Multiple sensitivity studies were completed and three are reported here. The first study focused on utilizing wide input parameter ranges to provide an opportunity to assess numerical robustness. The next two studies narrowed the parameter ranges to enable focus on understanding uncertainty at a fixed operating condition. The completion of the sensitivity studies improved understanding of the interdependence of multiple inputs on the responses. In addition, numerical stability of the simulations over wide parameter ranges, shows the feasibility of incorporating uncertainty‐based methods in the design and certification of inflatable space habitats. With the experience and trust gained, it is anticipated that these same methods will be applied to nonlinear, orthotropic models in the future.

Lyle, Karen H.↗

NASA NTRS2018

Structural Certification of Human-Rated Inflatable Space Structures

This paper details the results of an initial study to develop a certification plan for human-rated inflatable space structures, including guidelines for qualification testing. Habitable softgoods inflatables are multi-layered shell structures that use high-strength webbing, cordage and broadcloth fabric to carry the skin loads of a variety of volumetric shapes and structural architectures. The primary objectives of this study are to define the key parameters that affect these structures and propose a statistically robust approach to defining safety and knockdown factors based on test and analysis. Current NASA standards for habitable inflatable space structures use a factor of safety of 4, which was inherited from airship design criteria. An updated approach to defining a design factor, taking into account material strength variability, load variability in the article, number of test samples, and damage and degradation effects is specified. Accurate analytical modeling of these structures is hindered by the difficulty of obtaining accurate and consistent material data due to load-history- dependent, nonlinear load versus strain behavior. A building block approach to certification is detailed that uses stochastic modeling and statistical test design and analysis to address the unique challenges these high-strength softgoods structures present. Human-rated inflatable modules are a transformative capability for launching much larger habitable volumes into space than is possible with rigid shell structures. This research aims to provide the framework for certifying these structures for future human space exploration missions.

Jones, Thomas C.↗

NASA NTRS2017

Non-Axisymmetric Inflatable Pressure Structure (NAIPS) Full-Scale Pressure Test

Inflatable space structures have the potential to significantly reduce the required launch volume for large pressure vessels required for exploration applications including habitats, airlocks and tankage. In addition, mass savings can be achieved via the use of high specific strength softgoods materials, and the reduced design penalty from launching the structure in a densely packaged state. Large inclusions however, such as hatches, induce a high mass penalty at the interfaces with the softgoods and in the added rigid structure while reducing the packaging efficiency. A novel, Non-Axisymmetric Inflatable Pressure Structure (NAIPS) was designed and recently tested at NASA Langley Research Center to demonstrate an elongated inflatable architecture that could provide areas of low stress along a principal axis in the surface. These low stress zones will allow the integration of a flexible linear seal that substantially reduces the added mass and volume of a heritage rigid hatch structure. This paper describes the test of the first full-scale engineering demonstration unit (EDU) of the NAIPS geometry and a comparison of the results to finite element analysis.

Jones, Thomas C.↗

NASA NTRS2016

Non-Axisymmetric Inflatable Pressure Structure (NAIPS) Concept that Enables Mass Efficient Packageable Pressure Vessels with Sealable Openings

Achieving minimal launch volume and mass are always important for space missions, especially for deep space manned missions where the costs required to transport mass to the destination are high and volume in the payload shroud is limited. Pressure vessels are used for many purposes in space missions including habitats, airlocks, and tank farms for fuel or processed resources. A lucrative approach to minimize launch volume is to construct the pressure vessels from soft goods so that they can be compactly packaged for launch and then inflated en route or at the final destination. In addition, there is the potential to reduce system mass because the packaged pressure vessels are inherently robust to launch loads and do not need to be modified from their in-service configuration to survive the launch environment. A novel concept is presented herein, in which sealable openings or hatches into the pressure vessels can also be fabricated from soft goods. To accomplish this, the structural shape is designed to have large regions where one principal stress is near zero. The pressure vessel is also required to have an elongated geometry for applications such as airlocks.

Doggett, William R.↗

NASA NTRS2016

In-Space Structural Assembly: Applications and Technology

As NASA exploration moves beyond earth's orbit, the need exists for long duration space systems that are resilient to events that compromise safety and performance. Fortunately, technology advances in autonomy, robotic manipulators, and modular plug-and-play architectures over the past two decades have made in-space vehicle assembly and servicing possible at acceptable cost and risk. This study evaluates future space systems needed to support scientific observatories and human/robotic Mars exploration to assess key structural design considerations. The impact of in-space assembly is discussed to identify gaps in structural technology and opportunities for new vehicle designs to support NASA's future long duration missions.

Belvin, W. Keith↗

NASA NTRS2015

Tension Stiffened and Tendon Actuated Manipulator

Doggett, William R.↗

NASA NTRS2015

Structural Sizing Methodology for the Tendon-Actuated Lightweight In-Space MANipulator (TALISMAN) System

The Tendon-Actuated Lightweight In-Space MANipulator (TALISMAN) is a versatile long-reach robotic manipulator that is currently being tested at NASA Langley Research Center. TALISMAN is designed to be highly mass-efficient and multi-mission capable, with applications including asteroid retrieval and manipulation, in-space servicing, and astronaut and payload positioning. The manipulator uses a modular, periodic, tension-compression design that lends itself well to analytical modeling. Given the versatility of application for TALISMAN, a structural sizing methodology was developed that could rapidly assess mass and configuration sensitivities for any specified operating work space, applied loads and mission requirements. This methodology allows the systematic sizing of the key structural members of TALISMAN, which include the truss arm links, the spreaders and the tension elements. This paper summarizes the detailed analytical derivations and methodology that support the structural sizing approach and provides results from some recent TALISMAN designs developed for current and proposed mission architectures.

Jones, Thomas C.↗

NASA NTRS2015

Improvements to the Tendon-Actuated Lightweight In-Space MANipulator (TALISMAN)

Devices for manipulating and precisely placing payloads are critical for efficient space operations including berthing of spacecraft, in-space assembly, construction and repair. Key to the success of many NASA space activities has been the availability of long-reach crane-like devices such as the Shuttle Remote Manipulation System (SRMS) and the Space Station Remote Manipulation System (SSRMS). These devices have been used for many operations including berthing visiting spacecraft to the International Space Station, deployment of spacecraft, space station assembly, astronaut positioning, payload transfer, and spacecraft inspection prior to atmospheric re-entry. Retiring the Space Transportation System has led to the removal of the SRMS from consideration for in-space missions, thus creating a capability gap. Recognizing this gap, work was initiated at NASA on a new architecture for long-reach space manipulators. Most current devices are constructed by joining revolute joints with carbon composite tubes, with the joints accounting for the majority of the device mass. For example in the case of the SRMS, the entire device mass is 410 kg (904 lbm); the joint structure, motors, gear train, cabling, etc., accounts for the majority of the system mass because the carbon composite tubes mass is 46 kg (101 lbm). An alternate space manipulator concept, the Tendon-Actuated Lightweight In-Space MANipulator (TALISMAN) was created to address deficiencies in the current state-of-the-art in long-reach manipulators. The antagonistic tendon actuated joint architecture allows the motors actuating the joint to be removed from the joint axis, which simplifies the joint design while simultaneously providing mechanical advantage for the motors. The improved mechanical advantage, in turn, reduces the size and power requirements for the motor and gear train. This paper will describe recent architectural improvements to the TALISMAN design that: 1) improve the operational robustness of the system by enabling maneuvers not originally possible by varying the TALISMAN geometry; 2) enable efficient active antagonistic control of a joint while sharing cable between antagonistic tension networks; and 3) uses a unique arrangement of differential capstans to reduce motor torque requirements by an order of magnitude. The paper will also summarize recent efforts to enable autonomous deployment of a TALISMAN including the deployment concept of operations and associated hardware system design. The deployment forces are provided by the same motor systems that are used for articulation, thus reducing the mass associated with the deployment system. The deployment approach is being tested on a TALISMAN prototype which is designed to provide the same operational performance as a shuttle-class manipulator. The prototype has been fabricated and is operational in a new facility at NASA Langley Research Center that has a large area (15.2 m by 21.3 m [50 ft by 70 ft]) air-bearing floor.

Doggett, William R.↗

NASA NTRS2015

Environmental Effects on Long Term Displacement Data of Woven Fabric Webbings Under Constant Load for Inflatable Structures

An experimental study of the effects of environmental temperature and humidity conditions on long-term creep displacement data of high strength Kevlar and VectranTM woven fabric webbings under constant load for inflatable structures is presented. The restraint layer of an inflatable structure for long-duration space exploration missions is designed to bear load and consists of an assembly of high strength webbings. Long-term creep displacement data of webbings can be utilized by designers to validate service life parameters of restraint layers of inflatable structures. Five groups of high-strength webbings were researched over a two year period. Each group had a unique webbing length, load rating, applied load, and test period. The five groups consisted of 1.) 6K Vectran webbings loaded to 49% ultimate tensile strength (UTS), 2.) 6K Vectran webbings loaded to 55% UTS, 3.) 12.5K Vectran webbings loaded to 22% UTS, 4.) 6K Kevlar webbings loaded to 40% and 43% UTS, and 5.) 6K Kevlar webbings loaded to 48% UTS. Results show that all webbing groups exhibit the initial two stages of three of a typical creep curve of an elastic material. Results also show that webbings exhibit unique local wave patterns over the duration of the test period. Data indicate that the local pattern is primarily generated by daily variations in relative humidity values within the test facility. Data indicate that after a three to six month period, where webbings reach a steady-state creep condition, an annual sinusoidal displacement pattern is exhibited, primarily due to variations in annual mean temperature values. Data indicates that variations in daily temperature values and annual mean humidity values have limited secondary effects on creep displacement behavior. Results show that webbings in groups 2 and 5 do not exhibit well defined annual displacement patterns because the magnitude of the applied loads cause large deformations, and data indicate that material yielding within a webbing tends to neutralize the annual sinusoidal displacement pattern. Study indicates that applied load, environmental effects, mechanical strength, coefficient of thermal expansion, and hygroscopic properties of webbings are fundamental requirements for quantifying accurate creep displacements and behaviors over multiple year time periods. Results from a study of the environmental effects on long-term creep displacement data of Kevlar and Vectran woven webbings are presented to increase the knowledge base of webbing materials and to enhance designs of inflatable space structures for long-duration space missions.

Kenner, WInfred S.↗

NASA NTRS2015

Application of a Novel Long-Reach Manipulator Concept to Asteroid Redirect Missions

A high priority mission currently being formulated by NASA is to capture all or part of an asteroid and return it to cis-lunar space for examination by an astronaut crew. Two major mission architectures are currently being considered: in the first (Mission Concept A), a spacecraft would rendezvous and capture an entire free flying asteroid (up to 14 meters in diameter), and in the second (Mission Concept B), a spacecraft would rendezvous with a large asteroid (which could include one of the Martian moons) and retrieve a boulder (up to 4 meters in diameter). A critical element of the mission is the system that will capture the asteroid or boulder material, enclose it and secure it for the return flight. This paper describes the design concepts, concept of operations, structural sizing and masses of capture systems that are based on a new and novel Tendon- Actuated Lightweight In-Space MANipulator (TALISMAN) general-purpose robotic system. Features of the TALISMAN system are described and the status of its technology development is summarized. TALISMAN-based asteroid material retrieval system concepts and concepts-of-operations are defined for each asteroid mission architecture. The TALISMAN-based capture systems are shown to dramatically increase operational versatility while reducing mission risk. Total masses of TALISMAN-based systems are presented, reinforcing the mission viability of using a manipulator-based approach for the asteroid redirect mission.

Dorsey, John T.↗

NASA NTRS2015

Creep Burst Testing of a Woven Inflatable Module

A woven Vectran inflatable module 88 inches in diameter and 10 feet long was tested at the NASA Johnson Space Center until failure from creep. The module was pressurized pneumatically to an internal pressure of 145 psig, and was held at pressure until burst. The external environment remained at standard atmospheric temperature and pressure. The module burst occurred after 49 minutes at the target pressure. The test article pressure and temperature were monitored, and video footage of the burst was captured at 60 FPS. Photogrammetry was used to obtain strain measurements of some of the webbing. Accelerometers on the test article measured the dynamic response. This paper discusses the test article, test setup, predictions, observations, photogrammetry technique and strain results, structural dynamics methods and quick-look results, and a comparison of the module level creep behavior to the strap level creep behavior.

Selig, Molly M.↗

NASA NTRS2014

Development of a Tendon-Actuated Lightweight In-Space MANipulator (TALISMAN)

An invention of a new and novel space robotic manipulator is described. By using a combination of lightweight truss links, a novel hinge joint, tendon-articulation and passive tension stiffening, this new robotic manipulator architecture achieves compact packaging, high strength, stiffness and dexterity while being very lightweight compared to conventional manipulators. The manipulator is also very modular; easy to scale for different reach, load and stiffness requirements; enabling customization for a diverse set of applications. Novel features of the new manipulator concept are described as well as some of the approaches to implement these design features. Two diverse applications are presented to show the versatility of the concept. First generation prototype hardware was designed, manufactured and has been assembled into a working manipulator that is being used to refine and extend development efforts.

Doggett, William R.↗