Search NASA⌕ Search

Engineering topics

Jordan Kreitzman

Publications and source records attributed to Jordan Kreitzman.

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

An Experimental and Predictive Study of Bent-Chamber Acoustic Liners

Acoustic liner samples with rectangular, sharp chamber bends are 3D-printed and tested in the NASA Normal Incidence Tube. The angle of the bend is varied from 0 to 180 degrees. Four different methods are used to predict the impedance behavior of these samples: (1) midline-length assumption, (2) Cummings correction for curved duct bends, (3) Cummings prediction for 180 degrees sharp duct bends, and (4) Helmholtz equation via finite element method. Trends in the experimental data are discussed, predictions are compared to the experimental data, and recommendations are made on prediction method usage. Follow-on work is suggested, including capturing additional test points at higher frequencies and with different chamber geometries. Future modeling strategies are also briefly described.

chamber↗
NASA NTRS2024

Conceptual Design and Validation of a Bent-Perforation-Path Acoustic Liner

An acoustic liner concept is developed that increases the effective thickness of perforate sheet holes by bending the perforation paths within the facesheet. This significantly increases both the viscous-loss resistance and mass reactance properties of the acoustic liner, creating low-frequency absorption utilizing a small amount of liner volume. An initial concept is designed, 3D-printed, and tested in a normal-incidence impedance tube to verify the acoustic properties. Comparisons to an impedance model are shown with good agreement to test data, although further work needs to be done to more accurately capture the losses associated with bends within the hole. Follow-on concepts are also discussed that attempt to address the current shortcomings of the initial design.

acoustic liner perforate impedance↗
NASA NTRS2023

Acoustics Technical Working Group and UAM Noise Working Group Proceedings

The NASA Acoustics Technical Working Group Meeting originally started as a program planning meeting in 1992 and has grown through the years. The purpose of these biannual meetings is to foster communication and collaboration among NASA researchers and their university, industry, and government colleagues on activities and work of current and future mutual interest. The NASA-led Urban Air Mobility (UAM) Noise Working Group (UNWG) Meeting began in 2018 as a one-day meeting immediately following the Acoustics Technical Working Group Meeting. The UNWG utilizes four subgroups that conduct regular meetings throughout the year to focus on challenges facing UAM vehicles for community noise and acceptance. The four subgroups coordinate research for development of noise prediction tools/noise reduction technologies, ground and flight test methods, human response and metrics, and regulations and policy (led by the FAA). This work is a compilation of the presentations given at ATWG/UNWG Fall 2022 held in person and via Teams at NASA Glenn Research Center. All NASA content was previously submitted through STRIVES for public presentation. This is merely a compilation. Non-NASA content has permission to distribute. Slide 208 video is included in the Available Downloads as Medial.MOV.

Advanced Air Mobility↗
NASA NTRSDate not supplied

Investigation of the Impedance Characteristics of Perforate Sheet Hole Clustering Over an Array of Uniform Depth Chambers

A series of normal incidence impedance tube tests are conducted to characterize the facesheet impedance differences between uniformly distributed and nonuniformly tightly packed hole layout patterns, defined here as "hole clustering." These hole clustered samples contain the same number of holes as their uniformly distributed counterparts but target edge to edge distances between holes down to 0.01". Resonant frequency shifts between uniformly distributed and hole clustered samples are presented to demonstrate potential design benefits. Mass end correction differences between samples are also shown to better quantify differences in designs, including the effect of acoustic particle velocity. It is found that hole clustered facesheets over an array of uniform depth chambers can provide significant reactance increases at minimal expense to resistance, thereby lowering resonant frequencies. Additionally, moving these hole clustered layouts toward common chamber corners provides additional resonance shifts to lower frequencies.

acoustic liner impedance hole clustering perforate↗
NASA NTRSDate not supplied

Toward Fully 3D-Printed Two Degree of Freedom Acoustic Liners

An acoustic liner optimization tool is developed for designing two degree of freedom (2DOF) liners with high absorption over a wide range of frequencies and sound pressure levels (SPLs). Two additively manufactured 2DOF liners (one constant and one variable chamber depth) are designed and printed with an embedded perforate layer as the septum. A normal incidence impedance tube study is performed to directly compare impedance and absorption spectra to a more traditionally manufactured 2DOF liner with embedded mesh caps in phenolic honeycomb. Comparisons of test data to predictions are shown as well as SPL sensitivities for each acoustic liner. Broadband absorption is achieved with the 3D printed 2DOF liner containing constant chamber depths, although due to current limitations in printed embedded perforate hole size, not as broad as the traditional mesh cap liner. However, results also show that the 3D printed variable chamber depth sample is more comparable to the mesh cap liner absorption, demonstrating the viability of printed embedded perforates in novel concepts.

acoustic liner 2DOF two degree of freedom 3D print↗
NASA NTRSDate not supplied

Perforate Sheet Concepts for Improved Low-Frequency Absorption of Acoustic Liners

Two perforate sheet concepts are presented that attempt to improve the lower frequency absorption characteristics of acoustic liners: hole-clustered facesheet and bent-perforation-path facesheet. The theory behind each will be discussed, and normal incidence experimental data will also be shown to demonstrate acoustic benefits. Preliminary modeling efforts are in work and will be discussed as well.

acoustic liner perforate sheet low frequency absor↗
NASA NTRSDate not supplied

Influence of Source Type on Acoustic Liner Impedance in No Flow

This paper presents findings from a study conducted under a challenge of the International Forum for Aviation Research (IFAR), which consists of partners from various national research labs around the world. A series of normal incidence impedance tube tests are performed to identify differences in acoustic impedance for various types of source excitations. These source types include single-tone, multitone, and broadband. To better understand these differences, six unique acoustic liners are tested using these source types at various sound pressure levels and frequencies. Multitone sources of up to five discrete frequencies at a time (both harmonic and nonharmonic excitations) are included. Predictions are also shown to assess capability of capturing source type in the acoustic liner design process. It is determined that impedance behavior due to single-tone and broadband source excitations is largely well-understood and predictable. Multitone source excitations, however, yield unpredictable impedance characteristics that appear highly dependent on the summed coherent waveform that is incident upon the acoustic liner. Future work on this topic is warranted to improve impedance prediction capability of multitone excitation.

acoustic liner impedance multitone prediction sour↗
NASA NTRSDate not supplied

Extending Acoustic Liner Bandwidth with Simple Embedded Septa

An acoustic liner design incorporating single-hole perforate septa was evaluated by the NASA Langley Liner Physics Team. The design, termed the ‘Simplified Septa’ concept, incorporates embedded septa as found in traditional, multidegree-of-freedom liners. Generally, such septa are composed of multihole perforates or porous mesh, whereas this concept uses septa with one hole per cell. An optimization scheme was employed to determine septa placement and hole diameters based on a target impedance cost function. Versions of the concept are tested in the NASA Langley Normal Incidence Tube (NIT) to determine impedance and absorption spectra for swept tonal excitation at 120 and 140 dB. Experimental results are compared to predictions from a liner model based on the Zwikker-Kosten Transmission Line (ZKTL) code and show good agreement for no-flow conditions.

acoustics↗
NASA NTRSDate not supplied

Bypass Duct Acoustic Liner Design With and Without Bifurcation Effects

The growth in air traffic and the commitment to sustainable aviation continue to provide new challenges to reducing aircraft noise levels. Acoustic liner design methodologies must therefore provide the capability to efficiently predict the acoustic benefits of novel liner configurations within complex aircraft nacelle geometries. With these observations in mind, a broadband acoustic liner optimization process has been developed and assessed through a series of design and experimental studies at increasing technology readiness levels. This work applies the design process to the aft-fan noise component and explores the effects of bypass duct bifurcations (e.g., the pylon and lower bifurcation). In addition to this new application, the design study is expanded to include the use of a commercially available duct propagation code. Despite the different general workflow for the two propagation codes, consistent optimized impedance spectra and in-duct attenuation predictions were obtained for several acoustic treatment options. The preliminary results are promising, and this work increases confidence in the enhanced broadband liner design methodology and lays the groundwork for complimentary use of the codes in future studies. The potential benefits of acoustic treatment on the upper and lower bifurcations are also demonstrated. The knowledge gained through this preliminary stage of the liner design process will be used to guide the identification of candidate liner designs for a proposed static engine test within the next year.

Acoustic Liner Design↗