Search NASA⌕ Search

Engineering topics

Joseph N. Zalameda

Publications and source records attributed to Joseph N. Zalameda.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Thermal Inspection of Low Emissivity Surfaces Using a Pulsed Light Emitting Diodes (PLED) Heat Source

Thermal inspections of a structure typically utilize a flash or quartz lamp heat source located on the same side of an infrared camera. The heat source provides light energy for heating while the infrared camera measures the surface transient temperature response. The inspection can be difficult for low emissivity surfaces for several reasons. First, the high intensity light can reflect off the surface and cause “burn-in” to the camera’s detector. The “burn-in” can take time for the sensors to recover and potentially damage the detector. Secondly, the heat source after pulsing, has a transient cool down component. The cool down component can be reflected and therefore superimposed over the structure’s thermal response which can cause an error (false defect indications) in the inspection. Lastly, the heat source is spectrally broad and therefore while heating, infrared components of the heat source can produce non-uniformity in the measured temperature field. Typically for the inspection of reflective surfaces, paint or other emissivity enhancing coatings are applied before inspection. In this paper, a pulsed light emitting diodes (PLED) heat source is used. The PLED heat source is spectrally narrow, contained within the visible band, and therefore not detectable by the infrared camera. The PLED heat source is configured to reduce any transient cool down components that could produce false defect indications. The PLED thermal inspections are compared to commercially available flash thermography inspections on unpainted aluminum samples with simulated corrosion and additively manufactured Ti-6AL-4V metal specimens.

thermal nondestructive evaluation↗
NASA NTRS2024

Correlations of Additive Manufacturing Model-Based Process Metrics With Spatter-Induced Porosity in the Powder Bed Fusion-Laser Beam/Metallic Process

Components fabricated using the powder bed fusion laser beam metallic (PBF-LB/M) additive manufacturing (AM) process comprise a multitude of sequential weld passes. Qualifying materials for components in critical applications requires a thorough understanding of pertinent processing-microstructure-property relationships. Porosity defects have a strong adverse effect on the mechanical properties of a material. The morphology of porosity defects created by lack of fusion in PBF-LB/M often exhibit high aspect ratios that can act as stress concentrators and become crack initiation sites. The occurrence of spatter induced porosity is studied using synchronized AM model-based process metrics and porosity measured by high-resolution X-ray computed tomography. A novel AM process metric is introduced to quantify the relative exposure to spatter ejecta impacts and incorporation throughout the sequence of the PBF-LB/M process. Further characterization using optical metallography and scanning electron microscopy indicated that both keyhole and lack of fusion porosity correlated statistically with the spatter ejecta impact field of the PBF-LB/M process. Both keyhole and lack of fusion porosity can be predicted by the spatter exposure process metric, which can be exploited to control the fusion sequence.

Additive Manufacturing↗
NASA NTRSDate not supplied

TPSAS-NF1676L-30664-DND

- NASA Office of Safety and Mission Assurance (OSMA) Efforts - NASA Material Genome Initiative (MGI) - Following up effort: NASA Additive Manufacturing Structural Integrity Initiative (AMSII) - In-Situ Techniques for Additive Manufacturing

Joseph N. Zalameda↗
NASA NTRSDate not supplied

Delamination Depth Imaging for Quasi-Static and Fatigue Load Testing Using Passive Thermography

Passive thermography is used to monitor small increases in temperature resulting from delamination damage formation in composite hat-stiffened panels during both quasi-static and fatigue loading. It has been observed that rapid damage formation produces heating. This is composed of two heat generation components. The first component is an instantaneous response due to an irreversible thermoelastic strain release. The second component is mechanical heating, at the interface of failure, due to fracture damage. This produces a transient rise in temperature as the heat diffuses to the surface. The first component defines the thermal start time for the transient response. A one-dimensional thermal model is fitted to the data pixel by pixel, to produce imagery of the damage depth. The results are compared to ultrasonic and X-ray CT data.

Passive thermography↗
NASA NTRSDate not supplied

Quadrupole Simulations of Thermographic Responses of Composites

Thermography has been shown to be a viable technique for inspection of composites. The quadrupole method has been shown as a viable technique for rapidedly simulating the thermal repsonse of layered systems. Often, the effort has focused on a one-dimentional models, in particular for improved analysis of thermal data. For composites, the in-plane heat diffusion often significantly impacts the thermal response of defects of interest, therefore three-dimensional simulations are desirable. This paper discusses the extension of the quadrupole methodology to perform simulations of thermographic responses in three-dimensional configuration. This enables the more realistic simulations of the thermal response of delaminiations in composites. The simulations are compared to finite element simulations of the same inspection configurations. The simulations are also compared to the thermographic measurements on composites where shape and depth of the delaminations are known obtained from other sources.

Thermography↗
NASA NTRSDate not supplied

Acquisition and Processing of Passive Thermography Fatigue Test Data

Passive thermography is a large area inspection technique and is commonly used during fatigue loading of composite structures. Passive thermography allows for real time tracking of damage. This provides an accurate assessment of the damage progression as a function of load cycles and determines when the loading is stopped for ultrasonic or X-ray CT evaluations for detail damage assessment through-the-thickness. In addition, if new areas of damage growth are detected, with passive thermography, then those areas are additionally inspected with ultrasound or X-ray CT. A custom developed passive thermography inspection system for fatigue loading is presented. Passive thermography of damage progression is compared to ultrasound inspections as a function of the fatigue cycles. Discussion is made on processing of the thermal data for periodic and non-periodic thermal responses.

Thermal nondestructive evaluation↗
NASA NTRSDate not supplied

Comparison of In-situ Near Infrared Melt Pool Imagery to Optical Microscopy Measurements

Additive manufacturing (AM) is a rapidly growing technology. An area of major importance is the integrity and repeatability of AM parts. The goal is to reduce obstacles to certify AM built parts to allow for use in critical aerospace applications. In-situ nondestructive evaluation sensors can be used for build assessment and can potentially play a key role in certifying AM parts. For example, melt pool features are understood to have a strong correlation to microstructural defects and the use of a near infrared (NIR) camera can be used to record the melt pool, cooling areas, and temperature gradients during the build. This work explores the use of a low cost NIR camera to obtain single line track imagery of the Ti-6Al-4V melt pools for various processing parameters. The NIR camera is radiometrically calibrated and configured in-line with the laser source to obtain high resolution imagery of the melt pool shape and dynamics. The challenge to measure melt pool shapes is to identify the transition points between the metal solid to liquid phase. Factors for melt pool measurements such as thermal camera pixel resolution, surface emissivity, and blurring due to the laser beam movement are discussed. Lastly, the melt pool imagery are compared to optical microscopy measurements for validation.

additive manufacturing↗
NASA NTRSDate not supplied

The Additive Manufacturing Moment Measure - A Parallel Computation Technique for Determining Build Variance in the Laser Powder Bed Fusion Process

Additive manufacturing (AM) has unique process attributes that facilitate the creation of optimized, complex, and unique parts for aerospace applications. However, the multi-scale and complicated building process for AM parts can cause unexpected build conditions that result in microstructural variability within the deposited material. The need for richer datasets and computational modeling capabilities to improve AM process reliability is a consequence of this microstructural variability. A computational approach, referred to as the Additive Manufacturing Moment Measure (AM3), addresses this need by leveraging the way AM processes fuse material in precise, incremental steps. During the layering sequence, each previous step contributes to the condition of the current step at the center of the heat source. The precise steps can be selected to systematically create a time-space point field with co-located machine input and in-situ sensor data. The sequential nature of the AM process, coupled with nearest neighbor calculations, allows for a fully parallel computation for part-scale build profile analysis. The AM3 concept introduced here enables part-scale assessment directly from build files and in-situ process monitoring sensors alike. The AM moment measures were calculated for build point fields and compared with co-located in-situ and ex-situ nondestructive evaluation and optical microscopy observations. These comparisons permit a better understanding of how the sequential process actions can affect the quality of a laser powder bed fusion (LPBF) build. Details of the AM3technique will be discussed and compared to measured LPBF part characteristics. The AM3 results indicate a strong potential to advance the qualification process for aerospace applications.

Additive Manufacturing↗
NASA NTRSDate not supplied

Flash Thermal Diffusivity Measurements and Inspection of Additively Manufactured Ti-6Al-4V Specimens with Varying Process Parameters

Flash thermal diffusivity measurements were obtained on additively manufactured Ti-6Al-4V disk shaped specimens with various process parameters. For additively manufactured metal parts, processing parameters such as laser power and scanning speed are critical to ensure the desired microstructure. For this study, the laser powder bed fusion process parameters were changed at various angular sections on a 21 mm diameter and 3.0 mm thick disk. The measurement of thermal diffusivity was performed by fitting a 1-dimensional thermal model to the data pixel by pixel to produce an inspection image. The image revealed the detection of defects such as lack of fusion porosity and areas of aggregated porosity. The thermal diffusivity imagery was compared to immersion scan ultrasonic and X-ray computed tomography (CT) measurements for validation. Based on these results, additional samples were investigated using a single side thermal inspection technique to detect lack of fusion porosity and near surface voids.

thermal nondestructive evaluation↗
NASA NTRSDate not supplied

Composite Bond Line Measurements Based on A Bayesian Analysis of Flash Thermography Data

For bonded composite materials, an accurate characterization of the adhesive bond line is needed to predict failure modes and fracture toughness. In this paper, bond line thickness was estimated from data obtained using through transmission flash thermography. The forward model that predicts back surface temperature is based on a three layer heat diffusion equation with varying diffusivity and flux boundary conditions. The corresponding inverse problem of estimating bond line thickness from measurement data was solved using a Bayesian approach that assumed Gaussian priors for the bond line thickness and thermal diffusivity of the adherends. Finally, the outputs of the thermography based method were compared to measurements that were collected using a micrometer and ultrasound testing.

Flash thermography↗
NASA NTRSDate not supplied

Powder Bed Fusion Laser Beam Metals Additive Manufacturing: Process Monitoring Approaches for Qualification and Certification

The use of in-situ process monitoring is of interest to lower the cost of inspection for the qualification of powder bed fusion laser beam metal (PBF-LB/M) additively manufactured (AM) parts. Precise monitoring of the PBF-LB/M AM build process constitutes a multi-scale and multi-discipline task. There are several significant challenges to the in-situ approach: the synchronization of sensor signals to process steps; the physical interpretation and classification of sensor signals; managing very large datasets; and comparing the inputs with the observed monitoring signals. At NASA Langley Research Center, a configurable architecture additive testbed has been developed to monitor the build process with synchronized sensors. The philosophy and method adopted for the synchronization of the cameras with laser power and position throughout a complex PBF-LB/M AM build will be described. The synchronized in-situ monitoring signals are compared with ex-situ nondestructive inspection, x-ray computed tomography (XCT). Such comparisons permit a better understanding of how the sequential process actions of LPBF-AM can affect build quality. The multi-scale and complex process of printing additively manufactured (AM) parts can have unexpected, but predictable, build conditions that result in material microstructure variability. This presentation will describe an additive manufacturing model-based process metric (AM-PM) computational method that is a fully parallel reduced order modeling approach developed to evaluate the evolution of AM processes. This method couples the known sequence of the AM process with a physically informed nearest neighbors’ calculation to map the conditions of a part-scale build. The result is a map of the build that is derived directly from build files or in-situ process monitoring sensors. The methodology of the approach will be described and mapped to the porosity observed from XCT for a complex PBF-LB/M build. Such comparative results develop understanding of how the sequential process actions can affect the PBF-LB/M AM build quality and microstructure variability.

Laser Powder Bed Fusion↗
NASA NTRSDate not supplied

Correlations Between Porosity, Spatter, and Process Metrics for Powder Bed Fusion Laser Beam Metallic Additive Manufacturing

Components fabricated using the powder bed fusion laser beam metallic (PBF-LB/M)additive manufacturing process are the result of a multitude of weld passes conducted sequentially. Qualifying components for aerospace applications requires a thorough understanding of the process-structure-properties relationships. Porosity defects are known to have a strong adverse effect on the mechanical properties of a component. In particular, porosity defects created by lack of fusion have high aspect ratio morphologies leading to stress concentrations that become crack initiation sites. In the present work, the occurrence of spatter induced lack of fusion porosity was studied using synchronized in-situ process monitoring, additive manufacturing model-based process metrics, and high-resolution X-ray computed tomography. The results show that lack of fusion porosity is statistically correlated with unremoved welding spatter ejecta of the PBF-LB/M process and process metrics related to the hatching strategy.

Qualification↗
NASA NTRSDate not supplied

Assessment of Segmentation-Induced Deviations of Porosity Metrics in Powder Bed Fusion Additively Manufactured Components

Post processing X-ray computational tomography (CT) inspection data for additively manufactured (AM) components can induce deviations in defect quantification, affecting subsequent fatigue and failure predictions. To assess the influence and potential impact of segmentation-induced measurement deviations, this paper applies several segmentation techniques to X-ray CT data for powder bed fusion Ti-6Al-4V specimens exhibiting porosity conditions. X-ray CT reconstructions were segmented with varying techniques including Otsu’s thresholding, random forest, k-nearest neighbors, and the multilayer perceptron. Metrics such as pore size and global porosity were compared for internal validity. Then, top-down X-ray CT measurements of surface-breaking porosity were compared to optical profilometry for cross-validation.

Data fusion↗
NASA NTRSDate not supplied

Near Infrared In-situ Measurements for the Detection of Keyhole Porosity in Autogenous Ti-6AL-4V Welds

Certification of additive manufactured metal parts requires nondestructive evaluation (NDE) to ensure build quality. NDE can be performed during the build process or post build. For large parts with complex geometries, post build NDE can be challenging. In-situ NDE potentially provides a way to perform the inspection layer by layer. This work explores the use of a high speed near infrared (NIR) camera that is focused in-line with a laser to obtain high spatial and temporal resolution thermal imagery of the melt pool and associated cooling areas. The thermal data is obtained during a laser melting process using Ti-6AL-4V plate and of particular interest is the detection of keyhole porosity. Keyhole porosity can result from non-optimal build conditions, such as excessive laser power at a given laser scanning speed, that creates an entrapped bubble. The NIR measured melt pool and cooling areas are processed to detect keyhole porosity. The results are compared to X-ray CT results for validation.

additive manufacturing↗
NASA NTRSDate not supplied

Near Infrared In-situ Measurements for the Detection of Keyhole Porosity in Autogenous Ti-6AL-4V Welds

Certification of additive manufactured metal parts requires nondestructive evaluation (NDE) to ensure build quality. NDE can be performed during the build process or post build. For large parts with complex geometries, post build NDE can be challenging. In-situ NDE potentially provides a way to perform the inspection layer by layer. This work explores the use of a high speed near infrared (NIR) camera that is focused in-line with a laser to obtain high spatial and temporal resolution thermal imagery of the melt pool and associated cooling areas. The thermal data is obtained during a laser melting process using a Ti-6Al-4V plate and of particular interest is the detection of keyhole porosity. Keyhole porosity can result from non-optimal build conditions, such as excessive laser power at a given laser scanning speed, that creates an entrapped bubble. The NIR measured melt pool and cooling areas are processed to detect keyhole porosity. The results are compared to X-ray CT results for validation. Small keyhole pores buried deep were not detectable with this technique, however, some larger subsurface elongated pores along with some open surface pores did show some promise for detectability.

additive manufacturing↗