Search NASA⌕ Search

Engineering topics

Joshua E Miller

Publications and source records attributed to Joshua E Miller.

6 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2021

Hypervelocity Impact Study for Migration from Kevlar® KM2® 705 to KM2® Plus 775: Material Property Measurement and Evaluation as a Ballistic Enhancement in Whipple Shields

Dupont™, the manufacturer of Kevlar®, has begun migrating from KM2® to KM2® Plus for ballistic textiles. Kevlar® KM2® has become an essential element of numerous meteoroid and orbital debris (MMOD) shield systems primarily as a multi-layer insulation (MLI) enhancement, and as such, the migration has implications for numerous system level risk assessments for future vehicles that will need to use the newer KM2® Plus fiber system. While the chemical makeup of the two fabrics are identical, differences in processing have yielded higher tenacities and toughness for the KM2® Plus system. To address this migration, the Hypervelocity Impact Technology (HVIT) group in NASA Exploration Sciences at Johnson Space Center (JSC) has worked with the NASA Engineering and Safety Center (NESC), the Multi-Purpose Crew Vehicle (MPCV) and the MPCV European Service Module (MPCV-ESM) group of the European Space Agency (ESA) with its contractors Airbus and Thales Alenia Space-Italy (TAS-I) to study how KM2® Plus in the woven form of 850 denier 775 compares with KM2® in the woven form of 850 denier 705. The two forms of Kevlar® fabrics have been compared by direct-impact with a known mass and as the rear wall in Whipple shields using the two-stage, light-gas-gun at the Remote Hypervelocity Test Laboratory (RHTL) of NASA JSC White Sands Test Facility (WSTF). From these examinations, it has been found that KM2® Plus does in fact improve the ballistic performance as a ballistic enhancement of MLI with an estimated improvement of 9.5±6.1% between the two fabrics, and on a mass basis, the estimated mass of KM2® Plus 775 is 3.6±0.7% lighter than KM2 705, which means the mass performance improvement is even higher.

Joshua E Miller↗
NASA NTRS2021

Orion Meteoroid and Debris Analysis with a Single Kevlar® Layer Enhancement to the Propulsion Tank Multi-Layer Insulation: Comparison of the Observed Data and the Adjusted Ballistic Models

In a continual mass optimization effort for the Orion vehicle by NASA and its prime contractor Lockheed Martin Space, along with the European Space Agency (ESA) and its contractors Airbus and Thales Alenia Space-Italy (TAS-I), a series of shield characterization shots have been performed to quantify the ballistic enhancement of a single-layer of Kevlar® in multi-layer insulation (MLI). This enhanced MLI is part of Orion’s propulsion subsystem, and it is planned to replace a double-layer Kevlar® configuration starting at the Artemis IV mission. This effort has included fifty-two shield characterization shots for five different shield configurations over the four Orion propellant storage vessels. These storage vessels are located in the European Service Module (ESM). This shield characterization has been managed by the Hypervelocity Impact Technology (HVIT) group in NASA Astromaterials Research and Exploration Sciences at Johnson Space Center (JSC) for the NASA Engineering and Safety Center (NESC) and the Multi-Purpose Crew Vehicle (MPCV) program office in coordination with Lockheed Martin Space and Thales Alenia Space-Italy (TAS-I). The shield characterization has used the two-stage, light-gas-gun at the Remote Hypervelocity Test Laboratory (RHTL) of NASA JSC White Sands Test Facility (WSTF) for acceleration of projectiles to representative orbital impact speeds. From this shield characterization effort, a revised ballistic limiting equation (BLE) has been developed for each of the five representative shielding configurations of the ESM pressure vessels. This document provides a brief description of the shield configurations considered for the Orion program and the shield characterization findings. These results are compared to the assumed BLE for each configuration going into the Artemis missions that utilize this version of ballistic enhanced MLI. The models are integrated into a fourteen day High Lunar Orbit (HLO) mission as a representative reliability prediction impact for Orion, and it has been found that the predicted risk of a loss-of-crew (LOC) event is actually a little less than half of the assumed value that launched this design modification opportunity.

Joshua E Miller↗
NASA NTRSDate not supplied

Engineering Launch Methods for Non-Spherical Hypervelocity Projectiles

The use of carbon-fiber-reinforced polymer (CFRP) in modern satellites has led to a significant amount of space debris, including fragments of CFRP and high-density metals such as steel and copper, produced during catastrophic breakup events. To address this issue, NASA's White Sands Test Facility (WSTF) has been developing the capability to launch "flake-like" and long "needle-like" projectiles. WSTF tested projectiles with different length-to-diameter ratios (L/D), impacting aluminum Whipple shields with thermal blankets on the outer surface, at velocities exceeding 6 km/s. The results of the study suggest that launching and imaging shaped projectiles at high velocities is feasible. Ongoing research is now focused on improving the techniques for launching and imaging shaped projectiles under hypervelocity conditions.

Engineering↗