Search NASA⌕ Search

Engineering topics

Jubin, Robert Thomas

Publications and source records attributed to Jubin, Robert Thomas.

At least 19 records

Demonstration of Integrated PostIrradiation Process Steps forMultikilogram Amounts of Low- and High-Burnup Used Nuclear Fuels

sponsored research and development (R&D) on the advanced, closed nuclear fuel cycle, including post-irradiation processing of used fuels, recovery of separated components, and preparation of recycle nuclear fuels. During the period 2007–2010, kilogram-scale demonstrations of the integrated processing steps were performed for actual light water reactor (LWR) used nuclear fuels (UNF). These integrated processing demonstrations were called “the Coupled-End-to-End” (CETE) campaigns and were associated with the Global Nuclear Energy Partnership program, which ran concurrently. The demonstrations were carried out in the shielded hot cells and associated gloveboxes located in the Irradiated Fuels Examination Laboratory (IFEL) and the Radiochemical Engineering Development Center (REDC) at the Oak Ridge National Laboratory (ORNL). Limited circulation program reports and a few technical papers were issued. The subject document provides a comprehensive summary of results, technical comparisons, and conclusions obtained from the demonstration campaigns and subsequent associated R&D.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effect of NO x and Water Variations on Iodine Loading of AgZ

Reprocessing of used nuclear fuel will result in the release of several volatile radionuclides that need to be removed from facility off-gas streams before their release to the environment. Iodine, one of these radionuclides, is expected to be primarily released in the dissolver off-gas stream as iodine (I 2 ) or methyl iodide (CH 3 I). Sorbents that target I 2 and CH 3 I removal from the DOG stream will need to adsorb iodine under elevated temperatures and in the presence of water vapor and nitrogen oxides (NO x ). Previous studies examining the adsorption of CH 3 I and I 2 in the presence of NO x gases by silver-exchanged mordenite (AgZ), a zeolite mineral considered for use in this application, have resulted in slightly inconsistent conclusions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Iodine Retention of Long-chain Organic Iodides on Silver-based Sorbents under DOG and VOG Conditions

The aqueous reprocessing of used nuclear fuel releases four key volatile radionuclides ( 3 H, 14 C, 85 Kr, and 129 I) from the used fuel into the off-gas streams of a reprocessing facility. Some semi-volatile radionuclides such as 106 Ru may also be released into the gas streams. Compliance with US regulations may require removal of these radionuclides from the off-gas streams before their discharge to the environment (Jubin et al. 2017). Iodine is released during multiple unit operations within a plant and can be found in gas streams such as the shear off-gas, dissolver off-gas, vessel off-gas (VOG), and waste solidification off-gas. To achieve DFs >1,000, treatment of the plant off-gas streams must include, at minimum, removal of both the dissolver off-gas and VOG. A 2015 analysis showing that the speciation of iodine in the VOG is primarily composed of organic alkyl iodides and that abatement technology for organic iodides is not well developed has produced increased interest in removing iodine from VOG. The lack of knowledge surrounding iodine removal from the VOG prompted the Office of Nuclear Energy within the US Department of Energy to initiate experimental efforts targeted at understanding organic iodide removal from prototypic VOG streams. In 2018 a joint test plan was developed and issued by Oak Ridge National Laboratory and Idaho National Laboratory. This test plan is intended to guide a multiyear experimental effort that will provide substantial amounts of information about the removal of organic iodides from VOG streams. This document reports on the progress of Idaho National Laboratory and Oak Ridge National Laboratory in the execution of the joint test plan as of the end of fiscal year 2019. Silver-based sorbents are the primary removal technology being characterized, and this report includes data on iodine adsorption by reduced silver-exchanged mordenite (also called silver-exchanged zeolite [AgZ]) (as a baseline iodine sorbent) and silver-functionalized silica aerogel (AgAero or Ag Aerogel) (as an advanced iodine sorbent). Conclusions are preliminary in nature and reflect the ongoing execution of the test plan through close collaboration between the two laboratories.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Testing of an Iodine and Tritium Capture System for an NO₂-Based Tritium Pretreatment Process

The reprocessing of used nuclear fuel would release volatile radionuclides into the off-gas streams of a processing plant, including ³H, ¹⁴C, ⁸⁵Kr, and ¹²⁹I. One potential simplification to the management of the off-gas streams could be achieved through an efficient tritium pretreatment (TPT) step in which the UO₂ fuel is oxidized by either air or NO₂ before dissolution. The oxidation of the UO₂ fuel matrix will result in the release of tritium from the fuel. Upfront release of tritium from the fuel in a pretreatment step with subsequent tritium abatement can minimize or eliminate the distribution of tritium throughout a plant. This can decrease or eliminate the need for tritium capture on multiple off-gas streams and prevent distribution to the aqueous inventory. The use of NO₂ as the oxidant in an advanced tritium pretreatment (ATPT) allows for the oxidation to be performed at lower temperatures and may also result in the quantitative release of iodine from the fuel. The ATPT off-gas will contain up to 75 vol% NO₂ gas. Spencer et al. identified the most promising iodine sorbent as silver nitrate-impregnated alumina (AgA) and the most promising tritium sorbents as 3Å molecular sieve (3Å MS) and silica gel for radionuclide capture from ATPT off-gas streams. An initial series of tests were conducted in fiscal years 2017–2018 with the intent of demonstrating the recovery of iodine and tritium using these sorbents from a recirculating gas stream that simulated the NO₂ recycle loop envisioned for the ATPT system. These initial tests showed low tritium recoveries and significant variations in the iodine recovery on the AgA. Ultimately it was concluded, following disassembly of the system, that corrosion within the system was partially the cause of the poor recovery of both species. All components of that system were disposed of at the end of the analysis. One of the conclusions drawn from the initial tests pointed to the reconsideration of the materials of construction. Based on that recommendation a new test bed for the advanced TPT off-gas system, that addresses the issues identified in the fiscal years 2017 and 2018 scoping tests, was designed and constructed. The test bed used high nickel alloys wherever possible to address the previously observed corrosion issues, a redesigned surge tank to permit ease of purging, an improved feed injection system and a more modular system design that allowed testing of incremental increases in system complexity to allow the isolation of any element that results in changes to recovery of target species. Accompanying that design, a multifaceted test plan was completed. The overarching goals of this test series were two-fold. The first goal was to demonstrate the ability to recover both the iodine and tritium that would be released during TPT in a manner that the releases from the fuel can be quantified. The second goal was to demonstrate that the combined recovery system could operate in any of the three proposed TPT modes (once-through air or O₂, recirculating air or O₂, or recirculating NO x ). A total of 22 tests were completed. Ten tests examined tritium behavior under varying operating parameters, 8 tests examined iodine behavior under varying operating parameters, and 4 tests examined both tritium and iodine behavior. Silica gel was used for the tritium sorbent, and AgA or Ag-mordenite (AgZ) was used as the iodine sorbent. The following conclusions were drawn: Full recovery is achieved for both sorbates when no sorbent is in place indicating no accumulation within the test system. In even the simplest of the configurations (i.e., no sorbents in the columns), iodine is more difficult to transport and recover from the system than tritium. Analysis of the AgA iodine sorbent beds from the integrated tritium and iodine tests indicate quantitative iodine recovery can be achieved (within anticipated experimental errors). This system may provide a means for the quantification of the iodine released by the ATPT process within the experimental uncertainties. This would support 0.33 to 1.00 kg demonstrations of the ATPT process with actual used nuclear fuel. Iodine penetrated further into AgZ than into AgA when operated in gas recirculation mode. Tritium adsorbs to and cannot be fully recovered from the 10-cm column of silica gel at regeneration temperatures up to 140 °C.; Tritium adsorbs to and cannot be recovered from the 10-cm column of AgA at desorption temperatures up to 200 °C. Co-adsorbed tritium was recovered to a greater extent from AgZ than from AgA, but recovery was not complete. No visible corrosion was observed in the test system.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Design of, and Test Plan for, an Iodine and Tritium Capture System for a NO 2 -Based Tritium Pretreatment Process

The reprocessing of used nuclear fuel would release volatile radionuclides into the off-gas of a processing plant, including 3 H, 14 C, 85 Kr, and 129 I. One potential simplification to the management of the off-gas streams could be achieved through an efficient tritium pretreatment (TPT) step in which the UO 2 fuel is oxidized either by air or by NO2 before dissolution. Oxidation of the UO2 fuel matrix results in the release of tritium contained within. Upfront removal of tritium from the fuel in a pretreatment step, followed by the abatement of tritium, can minimize or eliminate the distribution of tritium throughout the plant, also decreasing or eliminating the need for tritium capture on multiple off-gas streams. The use of NO 2 as the oxidant in an advanced tritium pretreatment (ATPT) allow the oxidation to be performed at lower temperatures and may result in the quantitative release of iodine from the fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Quantify the Extent of Physisorption on Silver Based Sorbents under VOG Conditions

US regulations govern release limits for volatile radionuclides contained in the gaseous effluents of used nuclear fuel reprocessing facilities. Of the four volatile radionuclides that are most restricted by the release limits ( 3 H, 14 C, 85 Kr, and 129 I), 129 I will require the greatest degree of abatement. Within a reprocessing facility, the vessel off-gas stream will likely contain 1%–5% of the total iodine at parts per billion (ppb) concentrations. Studies conducted by the authors have now investigated both I 2 and methyl iodide (CH 3 I) adsorption by two silver-bearing sorbents, hydrogen-reduced silver-exchanged mordenite (Ag 0 Z) and silver functionalized aerogel (AgAerogel) at a range of concentrations up to 1,000 ppb. Throughout this suite of tests, and particularly in the case of CH3I adsorption tests, there was a significant discrepancy in the amount of iodine recovered on sorbent beds compared to the amount of iodine that was believed to be delivered to the test system.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Analysis of Krypton-85 Legacy Waste Forms: Part II

During a removal of legacy materials from one hot cell at the Idaho National Laboratory in 2010, five metal capsules and some loose zeolite material were identified as krypton (Kr) immobilization test specimens produced in the late 1970s under the Airborne Waste Management Program (AWMP). This AWMP research and development effort examined the encapsulation of 85Kr within a collapsed zeolite structure for use as a potential waste form for long-term storage. The recovered capsules appeared to have been placed to the side and remained untouched after the AWMP was halted in the mid-1980s. These reclaimed capsules and loose material presented a unique opportunity to study a potential 85 Kr waste form after three half-lives had elapsed. The first phase of this study included two parts: The first was to assess the physical condition of the capsule walls, and the second was to examine the Kr-containing material within the capsules. The first part of this study was previously reported and noted that substantial corrosion was observed throughout each capsule wall of the two previously breached capsules that were examined. One of these capsules had been hot isostatic pressed (HIPed) and one was not HIPed. The second part of the study examined the materials contained in the two previously breached capsules. There appears to be a relatively uniform distribution of Kr and rubidium throughout the pellets examined. The chemical composition of the pellets appears to be consistent with 5A molecular sieves. The material contained within the HIPed capsules showed ~1 at. % lead (Pb). The origin of the Pb is currently indeterminate. X-ray diffraction analysis shows a significant shift from the 5A structure, most likely due to the Kr encapsulation/sintering process that occurred when the samples were made. Calculations based on the energy dispersive spectrometry elemental analysis show a residual Kr level within the pellets that is within a factor of 2 of the reported Kr capacities for this type of processed material. This provides a clear indication that a significant fraction of the Kr initially encapsulated in the material remained within the waste form even following a significant breach of the capsule wall. As a result, it would appear that this Kr immobilization method, even in non-HIPed form, is very promising as a waste form for long-term storage. The successful analysis of these two breached capsules forms a solid basis for the future analysis of the remaining unbreached capsules, which offers the opportunity to provide an even more complete understanding of the long-term Kr retention performance of this promising waste form.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Testing of an Integrated Iodine Scrubber and Polishing Bed System

In 2016 an initial engineering evaluation and design of the off-gas abatement systems required for a hypothetical 1000 t/yr used nuclear fuel (UNF) reprocessing facility treating 5 yr–cooled, 60 GWd/tIHM UNF was completed. In this study two types of silver-based iodine sorbents were considered. The first was a silver-exchanged mordenite (AgZ), and the second was a silver-functionalized silica aerogel. In the initial design of the dissolver off-gas (DOG) iodine capture beds, the sorbent capacity was assumed to be 40 mg I/g sorbent. The total iodine released from the fuel, used as input for the design of the DOG system, was 1.635 kg/day. Tramp halogens increased this to ~5.1 kg/day on an iodine equivalent basis. The daily consumption of iodine sorbent was ~166 kg (including the mass transfer zones that have lower iodine loading). The iodine capture system was designed to utilize five beds in parallel. In this design each bed was ~1 m in diameter and 1.5 m long. This design allowed the beds to remain on line for 20 days, but at that point all five beds would need to be replaced, resulting in considerable material handling. It was proposed that the bed life could be extended and the number of parallel beds reduced if an aqueous iodine scrubber preceded the solid sorbent iodine capture beds. The testing described in this report was intended to provide an evaluation of an integrated system in which bulk iodine would first be removed by an aqueous NaOH scrubber with a target iodine decontamination factor (DF) of 10 to 50. This would reduce the sorbent usage by 90 to 95% and significantly reduce the associated frequent remote handling of the iodine filter beds. The effluent from the scrubber would then be passed through an AgZ sorbent bed to remove residual iodine. The integration of these unit operations was intended to demonstrate an iodine DF of >1000, which would facilitate regulatory compliance with regards to total volatile radionuclide emission from a reprocessing facility. Initial baseline performance testing of the scrubber system includes the characterization of CO 2 removal by the aqueous NaOH scrubber as a function of temperature, caustic concentration, packing length, liquid-to-gas mass ratio, and liquid flow rate. It was found that when the column was well wetted, very high CO 2 DFs were achieved (>650 and potentially as high as 15,000), preventing the ability to elucidate the effects of each specific variable tested. The L/G ratio in this system was not representative of typical L/G ratios found in industrial-scale scrubber systems. By significantly lowering the liquid recirculation rate to the point that column wetting was marginal, some significant variations in the CO 2 DF or CO 2 effluent concentrations could be observed. The additional tests conducted under these more adverse conditions still showed CO 2 DFs >100. The only operational parameter with significant effects was determined to be column length, with increased column length resulting in higher CO 2 DFs. Following these CO 2 tests, a single iodine scrubber test was performed deliberately at a condition indicated by the CO 2 demonstration to result in poor column performance. This was intended to establish a lower performance bound for iodine removal by the aqueous scrubber. The result showed that even under the adverse operating conditions, an iodine DF of >100 could be achieved. Finally, the aqueous scrubber and a AgZ polishing bed were integrated. This simple caustic scrubber system achieved an iodine DF of >12,000 for just the scrubber portion. Using this iodine DF, the iodine loading on the polishing bed was reduced by 99.993%. The performance of that integrated system was compared to a system including only a AgZ sorbent bed. The system without the scrubber also showed iodine DFs >3000 until breakthrough was observed. The loading on the saturated portion of the bed averaged 87.2 mg I 2 /gm AgZ. Comparing the penetration of iodine into the sorbent beds for these two systems showed a marked difference; the penetration with the scrubber was only 0.65 cm at a maximum loading of 0.11 mg I 2 /gm AgZ, whereas for the case without the caustic scrubber, the bed was saturated for the first 7 cm and breakthrough of the 13.3 cm bed occurred.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Preparation of Four Large-format Hot Isostatically Pressed I-AgZ Waste Form Samples for Performance Testing

Hot isostatic pressing (HIP) is being considered as a process to directly convert 129 I-bearing materials to a durable radiological waste form. Zeolites, specifically silver-exchanged mordenite (AgZ), have been studied extensively as potential radioactive iodine sorbents and will contain 129 I as chemisorbed AgI, a relatively insoluble compound with a high melting point. Oak Ridge National Laboratory has conducted several recent studies on the HIP of both I–AgZ and other iodine-bearing zeolites, resulting in an inventory of samples prepared with a suite of zeolites with varied iodine incorporation methods, pressing conditions, and sizes. These samples have been made available to researchers at other national laboratories in support of test method development to assess the stability of heterogenous iodine-bearing waste forms. The work described here generated four large-format HIPed I–AgZ samples. These samples are 1.5 in. diameter and 2 in. length and contain 49 g of I–AgZ. Two samples were prepared at an iodine loading of 64 mg I/g I– AgZ, and two samples were prepared at an iodine loading of 135 mg I/g I–AgZ. These two sets of duplicate samples will be made available upon request in support of iodine waste form durability method development efforts.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Design of Laboratory System to Recover Tritium from Zirconium Recycle and Plan to Test System

The objective of the tritium separations task is to develop a viable process to separate tritium from the zirconium recycle off-gas stream. In support of this long-term objective, the goal of the present work is to design a test system and prepare a test plan for an alternate tritium capture method suitable for, and compatible with, recycle of the reactive gas (i.e., chlorine) in the zirconium recycle process. The zirconium recycle process is under development to recover zirconium from the Zircaloy® cladding component of used nuclear fuel. Small quantities of all isotopes of hydrogen (all H) are trapped in the Zircaloy as zirconium hydride. Processing releases and converts this hydrogen to hydrogen chloride, including tritium-substitu ted hydrogen chloride, 3 HCl (a.k.a., TCl). This compound of tritium must be removed from the zirconium recycle process off-gas and sequestered to satisfy regulations governing emissions of tritium.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Extended Elemental Iodine Adsorption by AgZ under Prototypical Vessel Off-Gas Conditions

U.S. regulations will require the removal of 129 I from the off-gas streams of any used nuclear fuel (UNF) reprocessing plant prior to discharge of the off-gas to the environment. Multiple off-gas streams within a UNF reprocessing plant combine prior to environmental release, and each of these streams contains some amount of iodine. For an aqueous UNF reprocessing plant, these streams include the dissolver off-gas (DOG), the cell off-gas (COG), the vessel off-gas (VOG), the waste off-gas (WOG), and the shear off-gas (SOG). To achieve regulatory compliance, treatment of multiple off-gas streams within the plant must be performed. Of these remaining streams, the VOG is expected to be one of the major contributors to the balance of the residual iodine releases. The VOG will most likely contain iodine at parts-per-billion (ppb*) concentrations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Joint Test Plan for the Evaluation of Iodine Retention for Long-Chain Organic Iodides

A number of reports have identified four volatile radionuclides that arise from the reprocessing of nuclear fuel ( 3 H, 14 C, 85 Kr, and 129 I) that require controls limiting their environmental release from reprocessing facilities in order to meet US regulatory requirements. Of these, 129 I has the longest half-life and highest potential biological impact.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Testing of an Iodine and Tritium Removal System for Advanced Tritium Pretreatment Off-Gas

The reprocessing of used nuclear fuel would release volatile radionuclides into the off-gas of a processing plant, including 3 H, 14 C, 85 Kr, and 129 I. For a reprocessing plant sited within the United States and governed by US regulations, the abatement of some or all of these radionuclides from the plant off-gas would be required before discharge of that gas to the environment. A potential simplification of the off-gas management system can be achieved through an efficient advanced tritium pretreatment (ATPT) step in which the UO 2 fuel is oxidized by NO 2 prior to dissolution. Oxidation of the UO 2 fuel matrix results in the release of tritium contained within. Up-front removal of tritium from the fuel in a pretreatment step, followed by the abatement of tritium from the advanced tritium pretreatment off-gas (ATPTOG) stream, can minimize or eliminate the distribution of tritium throughout the plant, also decreasing or eliminating the need for tritium capture on multiple off-gas streams. The use of NO 2 as the oxidant allows tritium pretreatment to be performed at lower temperatures and may result in the quantitative release of iodine from the fuel. A total of five tests examined AgA as a potential iodine sorbent at an operating temperature of 150°C and both 3A MS and silica gel as potential tritium sorbents with an operating temperature of 40°C. 3A MS and silica gel are intended for use as regenerative sorbents, in which the adsorbed tritium (as tritiated water or tritiated nitric acid) is loaded onto the sorbent at operating temperature and then subsequently desorbed at high temperature into a small-volume gas stream for recovery and conversion to a waste form. This testing leaves many fundamental questions regarding the ATPTOG iodine and tritium abatement systems unanswered. These include questions regarding sorbent capacity and sorbate desorption. Overall, this testing indicates that tritium and iodine abatement from an ATPTOG stream by solid sorbents is currently at a low stage of technological development and that deployment of such an abatement system would require substantial additional research and development.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Techno-economic Analysis of Advanced Zeolite Membranes for the Concentration of Tritiated Water

This report describes the techno-economic analysis of advanced molecular sieve zeolite membranes to separate and concentrate tritiated water (HTO) from dilute HTO-bearing aqueous streams. In the first phase of this effort, several monovalent and divalent cation-exchanged silicoalumino phosphate (SAPO- 34) molecular sieve zeolite membranes were synthesized on disk supports and characterized with gas and vapor permeation measurements. In the second phase, Linde Type A (LTA) zeolite membranes were synthesized on disk and tubular supports. The pervaporation process performance was evaluated for the separation and concentration of tritiated water. Techno-economic analysis (TEA) on SAPO-34 and LTA membrane based technologies was completed. However, compared to the SAPO-34 membranes, LTA zeolite membrane performance both with respect to separation factor and permeance was superior and encouraging. LTA zeolite membranes were selected as the preferred option for comparison with the Combined Electrolysis and Catalyst Exchange (CECE) process for the concentration of tritiated water from dilute HTO-bearing aqueous solutions. It is estimated that the total energy cost to process 10 L/min of tritiated water for the membrane cascade system is substantially lower compared to the CECE process. A preliminary capital cost estimate for the membrane based system and the CECE process is also reported.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Design and Test Plan for an Integrated Iodine Scrubber and Polishing Bed System

The capture and subsequent immobilization of four regulated volatile radionuclides ( 3 H, 14 C, 85 Kr, and 129 I) and relevant semivolatile species from the off-gas streams of a used nuclear fuel (UNF) reprocessing facility has been a topic of significant research interest on the part of the US Department of Energy and other international organizations. Significant research and development has been conducted over the past decade. In 2016 an initial engineering evaluation and design of the off-gas abatement systems required for a hypothetical 1000 t/yr UNF reprocessing facility treating 5 yr–cooled, 60 GWd/tIHM UNF was completed. One of the key findings of that report was that the consumption rate of silver-based iodine sorbents in the dissolver off-gas primary iodine capture bed is very high and may warrant the evaluation of alternative methods to capture the bulk of the iodine that could significantly reduce the associated frequent remote handing of the iodine filter beds. This report is intended to describe the design of an experimental system that can be used to examine the use of aqueous scrubbing to remove the bulk of the iodine from the dissolver off-gas stream prior to a silver-based solid sorbent that would be used to provide the final iodine capture or polishing step. This report also provides a description of the initial series of tests that are proposed for this system.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Hot Isostatic Pressing of Engineered Forms of I-AgZ

Hot isostatic pressing (HIP) is being considered for direct conversion of 129 I-bearing materials to a radiological waste form. The removal of volatile radioactive 129 I from the off-gas of a nuclear fuel reprocessing facility will be necessary to comply with regulatory requirements regarding reprocessing facilities sited within the United States, and any iodine-containing media or solid sorbents generated by offgas abatement will require disposal. Zeolite minerals such as silver-exchanged mordenite (AgZ) have been studied as potential iodine sorbents and will contain 129 I as chemisorbed AgI. Oak Ridge National Laboratory (ORNL) has conducted several recent studies on the HIP of both iodine-loaded AgZ (I-AgZ) and other iodine-bearing zeolite minerals. The goal of these research efforts is to achieve a stable, highly leach resistant material that is reduced in volume as compared to bulk iodine-loaded I-AgZ. Through the use of HIP, it may be possible to achieve this with the addition of little or no additional materials (waste formers). Other goals for the process include that the waste form will be tolerant to high temperatures and pressures, not chemically hazardous, and that the process will result in minimal secondary waste generation. This document describes the preparation of 27 samples that are distinct from previous efforts in that they are prepared exclusively with an engineered form of AgZ that is manufactured using a binder. Iodine was incorporated solely by chemisorption. This base material is expected to be more representative of an operational system than were samples prepared previously with pure minerals.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Analysis of Krypton-85 Legacy Waste Forms: Part I

In 2010, five samples were reclaimed at the Idaho National Laboratory (INL). These samples were generated by R&D performed in the 1970’s relating to the long-term storage of 85 Kr and presented a unique opportunity to study a potential 85 Kr waste form after over three half-lives have elapsed. The container material of two of the reclaimed 85 Kr legacy waste form samples was examined by optical microscopy and by SEM-EDS. Substantial corrosion was observed throughout each sample container. The bulk of the container material was identified as carbon steel, while stainless steel was identified as the weld material used in container manufacture and/or sealing. The material used for Kr encapsulation was found adhered to the walls of each container and had a chemical composition consistent with zeolite minerals. Kr was found coincident with the adhered material, demonstrating that the encapsulation method used in the original experiments was effective in the long-term retention of Kr. In conclusion, the sectioning, mounting, and initial analysis of these legacy samples is an important step in the study of all five legacy 85 Kr waste forms and the information gained from the analysis of Samples 2 and 5 will be used to guide future efforts on these remaining samples.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

M3FT-17OR0301070211 - Preparation of Hot Isostatically Pressed AgZ Waste Form Samples

The production of radioactive iodine-bearing waste forms that exhibit long-term stability and are suitable for permanent geologic disposal has been the subject of substantial research interest. One potential method of iodine waste form production is hot isostatic pressing (HIP). Recent studies at Oak Ridge National Laboratory (ORNL) have investigated the conversion of iodine-loaded silver mordenite (I-AgZ) directly to a waste form by HIP. ORNL has performed HIP with a variety of sample compositions and pressing conditions. The base mineral has varied among AgZ (in pure and engineered forms), silver-exchanged faujasite, and silverexchanged zeolite A. Two iodine loading methods, occlusion and chemisorption, have been explored. Additionally, the effects of variations in temperature and pressure of the process have been examined, with temperature ranges of 525°C–1,100°C and pressure ranges of 100–300 MPa. All of these samples remain available to collaborators upon request. The sample preparation detailed in this document is an extension of that work. In addition to previously prepared samples, this report documents the preparation of additional samples to support stability testing. These samples include chemisorbed I-AgZ and pure AgI. Following sample preparation, each sample was processed by HIP by American Isostatic Presses Inc. and returned to ORNL for storage. ORNL will store the samples until they are requested by collaborators for durability testing. The sample set reported here will support waste form durability testing across the national laboratories and will provide insight into the effects of varied iodine content on iodine retention by the produced waste form and on potential improvements in waste form durability provided by the zeolite matrix.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗