Search NASA⌕ Search

Engineering topics

Kalinowska, Z

Publications and source records attributed to Kalinowska, Z.

Laser-produced aluminum plasma expansion inside a plastic plasma envelope

Previous experimental results demonstrated that the plasma pressure decreases with the growing atomic number of the target material. In this context, a question arose if the Al plasma outflow could be collimated using the plastic plasma as a compressor. To solve this problem, an experiment using a plastic target with an Al cylindrical insert was performed. The focal spot diameter substantially larger than that of the insert ensured simultaneous heating both target materials. This experiment proved that a production of Al plasma jets collimated by an action of outer plastic plasma is feasible [Kasperczuk et al., Laser Part. Beams 30, 1 (2012)]. The results of investigations presented here provide additional information on distributions of electron temperature in the outflowing plasma and time and space characteristics of ion emission, both registered at bare and constrained-flow Al targets. The experiment was carried out at the Prague asterix laser system iodine laser facility. The laser provided a 250 ps (full width at half maximum) pulse with the energy of 130 J at the third harmonic frequency ({lambda}{sub 3} = 0.438 {mu}m). A plastic target with an Al cylindrical insert of 400 {mu}m in diameter as well as a bare Al target (for comparison) was used. The focal spot diameter ({Phi}{sub L}) 1200 {mu}m ensured the lateral pressure effect of the plastic plasma strong enough to guarantee the effective Al plasma compression. The electron temperature measurements have shown that such Al plasma compression is accompanied by the increase of its temperature, dominance of which starts at distance of 0.5 mm from the target surface. Measurements of ion emission characteristics confirm the earlier numerical simulation prediction that in these conditions the plasma expansion geometry is closer to planar. The constrained Al plasma jet is very narrow and its axial velocity is considerably larger than the velocity of freely expanding Al plasma stream. It means that the plastic plasma envelope, besides the Al plasma compression, also strongly accelerates the Al plasma in its axial motion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Highly efficient accelerator of dense matter using laser-induced cavity pressure acceleration

Acceleration of dense matter to high velocities is of high importance for high energy density physics, inertial confinement fusion, or space research. The acceleration schemes employed so far are capable of accelerating dense microprojectiles to velocities approaching 1000 km/s; however, the energetic efficiency of acceleration is low. Here, we propose and demonstrate a highly efficient scheme of acceleration of dense matter in which a projectile placed in a cavity is irradiated by a laser beam introduced into the cavity through a hole and then accelerated in a guiding channel by the pressure of a hot plasma produced in the cavity by the laser beam or by the photon pressure of the ultra-intense laser radiation trapped in the cavity. We show that the acceleration efficiency in this scheme can be much higher than that achieved so far and that sub-relativisitic projectile velocities are feasible in the radiation pressure regime.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Plasma-wall interaction studies with optimized laser-produced jets

The production of the laser-produced plasma jets at burnt-through low-Z foils was optimized by using three-frame interferometry. When striking secondary targets, these jets of energetic particles represent an efficient tool for the investigation of transient phenomena at surfaces of the plasma-exposed solids. Two sets of precisely measured x-ray spectroscopic data demonstrate diagnostic potential of the collimated jets in the plasma-wall interaction studies: Blue Doppler shifts of the Al jet self-emission visualize ion deceleration in the near-wall region. Local depressions found in Al Ly{gamma} profiles emitted from Al/Si(PMMA) targets indicate charge exchange between the Al XIII and fully stripped C ions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Interaction of Cu and plastic plasmas as a method of forming laser produced Cu plasma streams with a narrow jet or pipe geometry

This brief communication is aimed at investigations of interaction of axially symmetrical light (plastic) plasma with heavy (copper) plasma. The use of axially symmetrical target compositions consisting of materials with low and high atomic numbers makes it possible to create different plasma stream configurations (e.g., very narrow jet or pipe). In the paper certain their applications are suggested.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experimental evidence of thermonuclear neutrons in a modified plasma focus

The PF-1000 plasma focus was modified by adding the cathode disk 3 cm in front of the anode. This modification facilitated the evaluation of neutron energy spectra. Two neutron pulses were distinguishable. As regards the first neutron pulse, it lasted 40 ns during the plasma stagnation and it demonstrated high isotropy of neutron emission. A peak neutron energy detected upstream was 2.46{+-}0.02 MeV. The full width of neutron energy spectra of 90{+-}20 keV enabled to calculate an ion temperature of 1.2 keV. These parameters and a neutron yield of 10{sup 9} corresponded to theoretical predictions for thermonuclear neutrons.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Fast-Neutron Source Based on Plasma-Focus Device

This paper describes investigations of neutrons produced by small plasma focus device PF-6 operating in the Institute of Plasma Physics and Laser Microfusion, Warsaw, Poland. Main parameters of neutron radiation have been measured by scintillation probe, and by activation technique. Current derivative probe has also been applied to measure dI/dt signal. Simultaneously neutron transport calculations have been carried out by Monte Carlo method. Finally, experimental measurements and numerical calculations have allowed concluding that plasma focus devices can be useful pulse neutron sources for different applications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗