Search NASA⌕ Search

Engineering topics

Kallman, J.

Publications and source records attributed to Kallman, J..

Explosive Formulation Code Naming SOP

The purpose of this SOP is to provide a procedure for giving individual HME formulations code names. A code name for an individual HME formulation consists of an explosive family code, given by the classified code dictionary, followed by a dash, -, and a number.

42 ENGINEERING↗

Plasma Modeling Results and shape control improvements for NSTX

New control implementations and dynamics studies on the National Spherical Torus eXperiment (NSTX) are summarized. In particular, strike point (SP) position, X-point height and squareness control, and two new system-identification methods / control-tuning algorithms were put into operation.The PID controller for the SP was tuned by analyzing the step response of the SP position to the poloidal coil currents, employing the Ziegler-Nichols method. The resulting SP controller was successfully employed to achieve the “snowflake” divertor configuration in NSTX. An offline system identification of the plasma response to the control inputs based on ARMAX input-output models was implemented. With this tool, rough estimates of the improvements were realized and several control improvements were identified.An online automatic relay-feedback PID tuning algorithm was implemented, which has the advantage of tuning the controller in one shot, thus optimizing the use of experimental time. Furthermore, using these new capabilities, we implemented LLD scenarios with control for theall four upper/lower/inner/outer SPs and with a combined X-point height, SP radius control. Separately, an independent squareness control was implemented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Biasing, Acquisition and Interpretation of a Dense Langmuir Probe Array in NSTX

A dense array of 99 Langmuir probes has been installed in the lower divertor region of the National Spherical Torus Experiments (NSTX). This array is instrumented with a system of elec- tronics that allows flexibility in the choice of probes to bias as well as the type of measurement (including standard swept, single probe, triple probe and operation as passive floating potential and scrape-off-layer (SOL) current monitors). The use of flush-mounted probes requires careful inter- pretation. The time dependent nature of the SOL makes swept-probe traces difficult to interpret. To overcome these challenges, the single- and triple-Langmuir probe signals are used in comple- mentary fashion to determine the temperature and density at the probe location. A comparison to mid-plane measurements is made. Work is supported by DOE contracts DE-AC02-09CHI1466 and DE-PS02-07ER07-29.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Strike Point Control for the National Spherical Torus Experiment (NSTX)

This paper presents the first control algorithm for the inner and outer strike point position for a Spherical Torus (ST) fusion experiment and the performance analysis of the controller. A liquid lithium divertor (LLD) will be installed on NSTX which is believed to provide better pumping than lithium coatings on carbon PFCs. The shape of the plasma dictates the pumping rate of the lithium by channeling the plasma to LLD, where strike point location is the most important shape parameter. Simulations show that the density reduction depends on the proximity of strike point to LLD. Experiments were performed to study the dynamics of the strike point, design a new controller to change the location of the strike point to desired location and stabilize it. The most effective PF coils in changing inner and outer strike points were identified using equilibrium code. The PF coil inputs were changed in a step fashion between various set points and the step response of the strike point position was obtained. From the analysis of the step responses, PID controllers for the strike points were obtained and the controller was tuned experimentally for better performance. The strike controller was extended to include the outer-strike point on the inner plate to accommodate the desired low outer-strike points for the experiment with the aim of achieving "snowflake" divertor configuration in NSTX.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The impact of lithium wall coatings on NSTX discharges and the engineering of the Lithium Tokamak eXperiment (LTX)

Recent experiments on the National Spherical Torus eXperiment (NSTX) have shown the benefits of solid lithium coatings on carbon PFC's to diverted plasma performance, in both L- and H-mode confinement regimes. Better particle control, with decreased inductive flux consumption, and increased electron temperature, ion temperature, energy confinement time, and DD neutron rate were observed. Successive increases in lithium coverage resulted in the complete suppression of ELM activity in H-mode discharges. A liquid lithium divertor (LLD), which will employ the porous molybdenum surface developed for the LTX shell, is being installed on NSTX for the 2010 run period, and will provide comparisons between liquid walls in the Lithium Tokamak eXperiment (LTX) and liquid divertor targets in NSTX. LTX, which recently began operations at the Princeton Plasma Physics Laboratory, is the world's first confinement experiment with full liquid metal plasma-facing components (PFCs). All materials and construction techniques in LTX are compatible with liquid lithium. LTX employs an inner, heated, stainless steel-faced liner or shell, which will be lithium-coated. In order to ensure that lithium adheres to the shell, it is designed to operate at up to 500–600 °C to promote wetting of the stainless by the lithium, providing the first hot wall in a tokamak to operate at reactor-relevant temperatures. The engineering of LTX will be discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗